Savant SmartControl 3 User manual

Box Contents
(1) SmartControl 3 Controller (SSC-W003I-00)
(1) Installation Kit SmartControl 3 (075-0174-xx)
(1) Mounting Plate (074-0569-xx)
(1) 6-pin Screw Down Plug-in Connector (028-9352-xx)
(1) 5V DC 1.2A Power Supply (025-0165-xx)
(1) Cable Tie (014-0071-xx)
(1) Quick Reference Guide (this document)
Specifications
Environmental
Environmental
Temperature
32° to 104° F (0° to 40° C)
Humidity
10% to 80% RH (non-condensing)
Dimensions and Weight
Dimensions and Weight
Height
0.64 in (1.62 cm)
Width
2.70 in (6.85 cm)
Depth
2.67 in (6.78 cm)
Weight
Net: 0.25 lb (0.11 kg)
Weight
Shipping: 1.50 lb (0.68 kg)
Power
Power
Input Power
5V DC 1.2A
Max Power
6 watts
Standards
Standards
Wireless
Wi-Fi (802.11 b/g/n 2.4 GHz)
Security
WPA1™, WPA2™, WPA1™ + WPA2™, WEP
Regulatory
Regulatory
Safety and Emissions
FCC Part 15 | CE Mark | C-Tick
Contains FCC ID:
TLZ-CU277
Contains IC:
6100-CU277
RoHS
Compliant
Minimum Supported Release
Minimum Supported Release
Savant OS
da Vinci 7.0
Network Requirements
Savant requires the use of a wireless network that is configured to
make use of at least one of the supported wireless Standards listed
in the Specifications Table.
Connect all Savant devices to the same local area network (LAN) or
subnet as the host. Savant recommends not implementing any type
of traffic or packet shaping in your network topology for the Savant
devices as this may interfere with performance.
Network Configuration
To ensure that the IP Address will not change due to a power outage,
a static IP Address or DHCP reservation should be configured.
Savant recommends using DHCP reservation within the router. By
using this method, static IP Addresses for all devices can be
managed from a single UI avoiding the need to access devices
individually.
Setting DHCP reservation varies from router to router. Refer to the
documentation for the router to configure DHCP reservation.
Connecting to a Wireless Network
Refer to the SmartControl 3 (SSC-W003I) Deployment Guide
located on the Savant Customer Community to connect the SSC-
W003I to the network.
Front Panel
A
Press and hold for 5 seconds while powered On to clear
network settings. Status LED will blink rapidly when reset is
complete.
Off:No Power
On Solid: Connected/Communicating with the Savant host.
Blinks Once: In Access Point Provisioning Mode and is ready to
be provisioned onto the local network.
Blinks Twice: Is connecting to the local network.
B
Blinks Three Times: Is connecting to the host.
Short OffBlink: Firmware is updating.
Rapid Blink: The reset button was held down for at least
five seconds and the SSC-W003I is performing a factory
reset.
Rear Panel
IR
Used to send IR signals to control devices with an
IR input or IR receiver via an IR flasher (5V
tolerant only).
6-pin Screw Down Plug-in Connector
See IR Wiring for important precautions regarding
IR functionality before making any connections.
Input Power
5V DC 1.2A - Connect to included power supply.
Cable Lance
Use with included cable tie to secure power
supply connection.
SSC-W003I-00 | 009-1258-01 | 160217
45 Perseverance Way, Hyannis, MA 02601
Copyright © 2016 Savant Systems, LLC
1
of
2
Savant.com | 508.683.2500
Savant® SmartControl 3
Quick Reference Guide
For Product Info

IR Wiring
IR connections are made using the 6-pin Screw Down Plug-in
Connectors supplied with controller. See Making Connections
section below when wiring.
IMPORTANT! IR Wiring Precautions
•Ensure that all IR emitters are within 15 feet (4.6 meters) from
the controllers location.
•Use of 3rd party flashing IR emitters with Talk Back is not
recommended. These types of emitters can draw voltage away
from the IR signal that can degrade IR performance
Making Connections
1. Remove Power if power is applied.
2. Pull to remove the terminal block from the rear of the controller.
3. With a small flat bladed screwdriver, turn the screws on the top of
connector counterclockwise until the silver crimps in the front of
the connector opens enough to slide the wires into the square
slots.
4. Insert one of the stripped wires from the devices being controlled
into its respective slot in the connector. Refer to the diagram
above.
5. Turn the screw clockwise until the screw tightens around the wire.
Tug on the wire a bit to verify it is installed securely. Do not allow
more than 1/2 inch of stripped wire exit from the rear of the
connector.
6. Repeat for each wire till all wires are installed.
7. Plug terminal block back into rear of the controller.
8. Reapply power
Additional Documentation
Additional Documentation is available on the Savant Customer
Community.
•SmartControl 3 (SSC-W003I) Deployment Guide - 009-1274-xx
•Savant Controllers Family video in the Savant University pages.
Regulatory
The following statements are applicable to the Savant SmartControl
3 SSC-W003I controller.
FCC Regulations:
15.19. These devices comply with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) These devices may not
cause harmful interference, and (2) these devices must accept any
interference received, including interferences that may cause
undesired operation.
15.21. The changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to
operate the equipment.
15.105. This equipment has been tested and found to comply with the
limits for CLASS B digital device, pursuant to Part 15 of FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a residential
environment. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications, However there is no guarantee that interference
will not occur in a particular installation, If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment offand on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving circuit different from that to which
receiver is connected.
- Increase the separation between the equipment and the receiver.
- Consult the dealer or experienced radio/TV technician for help.
IC Regulations:
RSS-Gen 7.1.3. These devices comply with Industry Canada license-
exempt RSS standard(s). Operation is subject to the following two
conditions: (1) These devices may not cause interference, and (2)
These devices must accept any interference, including interference
that may cause undesired operation of the device.
RSS-21- Annexe 9: A 9.4. Le présent appareil est conforme aux CNR
d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d'en compromettre le fonctionnement.
SSC-W003I-00 | 009-1258-01 | 160217
45 Perseverance Way, Hyannis, MA 02601
Copyright © 2016 Savant Systems, LLC
2
of
2
Savant.com | 508.683.2500