Savant S2 User manual

SHR-S2-00 | 009-1907-01 | 200127
Copyright 2020 Savant Systems, LLC
45 Perseverance Way, Hyannis, MA 02601
Savant.com | 508.683.2500
1 of 2
Front Panel
Reset Status
A B
AReset Button
To clear all Ethernet settings and revert them
back to their factory defaults, press and hold the
reset button for five seconds until the LED blinks
red rapidly; then release.
B
Status LED
O: Disconnected from power supply.
Amber: Host is booting/rebooting and is
disconnected from the network.
Amber Blinking: Host is in provisioning mode
and ready to be added to a network. Host is not
assigned an IP Address.
Green: Connected to the local network and is
assigned an IP Address.
Box Contents
(1) Savant® S2 Host Rack Mountable - (SHR-S2-00)
(1) Install Kit (075-0221-xx)
(1) Mounting Plate (074-0577-xx)
(1) 5V DC 3A Power Supply
with Quick Change AC Adapters ( 025-0216-xx)
(2) 6-pin Screw Down Plug-in Connector Black (028-9352-xx)
(2) 3-pin Screw Down Plug-in Connector Black (028-9351-xx)
(1) 4 inch Cable Tie (014-0071-xx)
(1) Product and Regulatory Insert (009-1782-xx)
Specifications
Environmental
Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 90% Relative Humidity (non-condensing)
Cooling 10 CFM
Maximum BTU 51.5 BTU/hr
Dimensions and Weights
Height 1.4 in (3.5 cm)
Width 6.00 in (15.2 cm)
Depth 3.20 in (8.1 cm)
Weight Net: 0.5 lb (0.22 kg)
Shipping 1.5 lb (0.68 kg)
Rack Space 1U
Power
Input Power 5V DC 3A
Maximum Power 15 watts
Standards
Wireless
Wi-Fi (802.11 a/b/g/n 2.4/5.0 GHz)
IMPORTANT! 802.11r (fast roaming) is not
supported
Security WPA™, WPA2™, WPA/WPA2™
Regulatory
Safety and
Emissions
FCC Part 15 CE C-Tick ICES-003
FCC ID Z64-WL18DBMOD
IC 451I-WL18DBMOD
RoHS Compliant
Minimum Supported Release
Savant Software da Vinci 9.1.3
Studio 3.0.2
Chassis Installation
The S2 Host can be installed on a solid, flat, level surface such as a
table, cabinet, or shelf. The location should be dry, well ventilated, and
out of direct sunlight.
Rack
The optional RCK-3000-xx provides a ventilated shelf for mounting
S2 Hosts. This rack is compatible with all standard 19-inch National
Electrical Manufacturers Association (NEMA) rack mounts.
Mounting Plate
A mounting plate (074-0577-xx) is supplied with the SHR-S2. This
mounting plate is used to mount the Host to a wall or existing
structure. To mount the Host, follow the instructions below.
1. Position the mounting plate onto the wall where the Host will be
located. Position the bracket so the tabs that hold the Host are
positioned horizontally.
2. Mark the two mounting holes on the wall.
3. Install wall anchors and screw mounting plate to the wall.
4. Snap the SHR-S2 Host into the bracket so the tabs on the mounting
bracket seat into the slots on the side of the Host.
Host
Mounting
Bracket
Tab fits
into slot
Further Product Information
To view available documentation, detailed product specs, and more:
–Visit the Savant Knowledge tab via the Savant Customer
Community to search all Savant documentation.
Savant® S2 Host Rack Mountable
Quick Reference Guide

SHR-S2-00 | 009-1907-01 | 200127
Copyright 2020 Savant Systems, LLC
45 Perseverance Way, Hyannis, MA 02601
Savant.com | 508.683.2500
2 of 2
Control Connections
RS-232 Wiring
Pin 1: No Connection Pin 5: RXD (Receive)
RJ-45 Connector
(Gold pins facing up)
Pin 1 Pin 8
Pin 2: No Connection Pin 6: TXD (Transmit)
Pin 3: No Connection Pin 7: CTS (Flow Control)
Pin 4: GND (Ground) Pin 8: RTS (Flow Control)
IMPORTANT!
–Wire colors are included to identify the pins used for this
connection. Colors shown do not represent any wiring standard.
–When wiring, DO NOT connect any wires within the cable that are
not required for communications.
–Pins 7 & 8 are only required for CTS/RTS handshaking.
–CTS/RTS handshaking is supported for flow control based on the
profile used in the Blueprint configuration.
–RS-422/485 is not supported
–Refer to the RS-232 Conversion to DB9 and RS-422/485 Pin-out
Application Note on the Savant Customer Community for more
information on RJ-45 to DB9 adapters oered by Savant.
Relay Wiring
Both Normally Open
and Normally Closed
outputs are available.
Pin 1: NC
(Normally Closed)
32
1
NC NOC / /
Pin 2: Common
Pin 3: NO
(Normally Open)
GPIO - General Purpose Input/Output
–GPIO’s configured
as an output can
be used to trigger
an action within
the system such as
switching a device.
–GPIO configured
as an input can
detect a state
change and trigger
a workflow.
Pin 1: GND (Ground)
32
1
GPIO 1
Standard
GPIO Using
PD Jumper
Gnd
I/O
PD
Pin 2: GPIO 1
Pin 3: PD (Pulldown)
–GPIO pins configured as an input are pulled high to (+12V) during
the boot process. To force the GPIO signal low during a boot-up.
Connect the PD pin to the GPIO pin. This forces the GPIO output to
(< 0.8V) during the processor boot times.
IR Wiring (Infrared)
–Ensure the all IP emitters
are within 15 feet (4.6
meters) from the
controllers location.
–Use of 3rd party
flashing IR emitters
with Talk Back is not
recommended. These
types of emitters can
draw voltage away from
the IR signal that can
degrade IR performance.
Pin 1: IR 1 -
1
IR1
+-+-+-
2
IR2
3
IR3
4 5 6
Use White Stripe
for Positive (+)
Pin 2: IR 1 +
Pin 3: IR 2 -
Pin 4: IR 2 +
Pin 5: IR 3 -
Pin 6: IR 3 +
–IR connections IR4 to IR6 (not shown in diagram) follow the same
wiring as connections IR1 to IR3.
Rear Panel
USB Audio Ethernet RS232-1 RS232-2
+
2
+
-1-
IR
3
-+C
Relay
NC NO
++
-4-5+ -61
GPIO
G PD
5VDC
A B C D E
F
G
H
A
Audio
96k / 24 bit fixed volume TOSLink (Optical)
digital audio output. Connect to digital optical
audio input on switcher for using the Audio
Interrupt Service (AIS).
BEthernet
8-pin RJ-45 female.
10/100/1000 Base-T auto negotiating port.
Connecting to this port will disable Wi-Fi
settings.
C
RS-232
8-pin RJ-45 female.
Used to transmit and receive serial binary data to
and from serial controllable devices.
Ports 1-2 RS-232 - CTS/RTS handshaking. CTS
RTS handshaking availability is based on the
component profile.
See RS-232 Wiring section for pin-outs.
D
IR
6-pin Screw Down Plug-in Connector. Used to
send IR signals to control devices with an IR input
or IR receiver via an IR flasher (5V tolerant only).
See IR Wiring section for important precautions
regarding IR functionality before making
connections.
E
Relay
3-pin Screw Down Plug-in Connector. See Relay
Wiring section for pin-outs.
Normally Open (NO) / Normally Closed (NC) to
control devices requiring basic on/o operation.
DC Voltage Max: 30V DC 1A
F
USB Not Used
GGPIO
3-pin Screw Down Plug-in Connector. See GPIO
Wiring section for pin-outs.
GPIO Input - When configured as an input, the
processor will look for a low (<0.8V DC) or a high
(>2.4V DC) state. Minimum 0V DC / Maximum
12V DC.
GPIO Output - When configured as an output,
the port provides a binary output of 0-12V DC
150mA max.
H5V DC
5V DC 3A - Connect included wall wart power
supply between the 5V DC connection and a 115-
240V AC surge protected outlet.
Network Configuration
To ensure the IP Address will not change due to a power outage, a
static IP Address or DHCP reservation should be configured. Savant
recommends using DHCP reservation within the router. By using this
method, static IP Addresses for all devices can be managed from a
single UI, avoiding the need to access devices individually.
Setting DHCP reservation varies from router to router. Refer to the
documentation for the router to configure DHCP reservation.
Refreshing the IP Connection
After connecting to a new network, changing routers, or if the IP
Address range in the router was changed, the IP connection should be
refreshed. To refresh the IP connection, do one of the following:
–Hot Plug the Ethernet (LAN) Connection
–Cycle power