Savant CPT-1212 User manual

The Component Profile Tool (CPT-1212) is a general purpose tool for
creating, testing, and modifying the .xml Profiles used in the RacePoint
Blueprint® software. The CPT-1212 kit includes all the tools described in
the Box Contents section below set in a durable carry case.
The CPT-1212 works with both the Profiler and IR Translator applications
to create new or modify existing .xml Profiles. This Quick Reference
Guide describes each of the tools in the kit along with general
information on connecting the system. For information on using the
Profiler and IR Translator software to test, modify, or create .xml Profiles,
refer to the Profiler and Component Profile Tool Reference Guide
009-1037-xx on the Savant Customer Community.
Box Contents
(1) SmartControl 12 (SSC-0012-xx)
(1) Installation Kit SmartControl 12 (075-0180-xx)
(1) SmartControl Mounting Plate (074-0577-xx)
(1) 12V DC 1.5A Power Supply (025-0166-xx)
(4) 6-pin Screw Down Plug-in Connector (028-9352-xx)
(1) Cable Tie (014-0071-xx)
(4) RJ45 to DB-9F Serial Control Adapters
(1) DB9 Gender Changer
(1) IR Learner (064-0224-xx)
(1) Keyspan High-Speed USB to Serial Adapter (064-0225-xx)
(2) Ethernet Cable - 2.0 ft (60.96 cm) (064-0059-xx)
(1) IR Repeater Cable (064-0020-xx)
(1) IR Learner (064-0224-xx)
(1) Technicians Screwdriver (015-0075-xx)
(1) Carry Case
(1) Quick Reference Guide (this Document)
Specifications
Environmental
Environmental
Temperature
32° to 104° F (0° to 40° C)
Humidity
10% to 80% RH (non-condensing)
Dimensions and Weight (Carry Case with all Components)
Dimensions and Weight (Carry Case with all Components)
Height
12.25 in (31.12 cm)
Width
16.0 in (40.64 cm)
Depth
5.5 in (13.97 cm)
Weight
Net: 4.25 lb (1.93 kg)
Shipping: 5.00 lb (2.27 kg)
Power (SSC-0012 Controller)
Power (SSC-0012 Controller)
Input Power
12V DC 1.5A
Max Power
18 watts
Compliance
Compliance
Safety and Emissions
FCC Part 15 | CE Mark | C-Tick
RoHS
Compliant
Minimum Supported Release
Minimum Supported Release
Savant OS
da Vinci 7.0
SSC-0012 Controller
The main component in the CPT-1212 kit is the SSC-0012 controller. The
Profiler software first transmits the command data to the controller. The
controller then converts the data and transmits this data to the Unit
Under Test (UUT). Dependent on the UUT, the data sent to the UUT can
be IR, RS-232, or IP.
Front Panel
A
Reset Button
Press and hold for 5 seconds while powered
on to clear network settings. The Status LED
will blink rapidly when controller starts its
boot sequence.
B
Status LED
Off:No power
Blinks Once: Access Point Provisioning Mode
Blinks Twice: Waiting for a Host Connection
Blinks Three Times: Connecting To Host
Solid: Connected to Host
Rear Panel
Note: Connections not identified in the diagram above are not used
when using the Component Profile Tool to create, test and modify .xml
Profiles.
A
Ethernet
• 10/100 Base-T auto-negotiating port with Link
and Activity LEDs.
• 8-Pin RJ-45 female.
• Connects to either a local unmanaged switch/hub
or directly into the Ethernet port on the SDE/
MacBook. Refer to the Diagram section.
B
Link LED
•Off:Ethernet link is not established.
•Green Solid: Ethernet link is established.
•Green Blinking: Ethernet activity is occurring
C
Data Rate
LED
•Off:10 Mbps data rate
•Green: 100 Mbps data rate
D
RS-232
• When selected in software, the RS-232 port
transmits and receives command codes between
the SSC-0012 and Unit Under Test. Refer to
Diagram section.
• 8-pin RJ-45 female.
• Ports 1 or 2 are selectable in the Profiler software.
E
IR
• When selected in software, the IR port transmits
command codes to the Unit Under Test (UUT).
• IR Repeater/Flasher connects to the required port
on the 6-pin Screw Down Plug-in Connector.
• IR Ports 1 - 6 are selectable in Profiler software.
F
Input
Power
• 12V DC 1.5A - Connect to included power supply.
G
Cable
Lance
• Used with included cable tie to secure power
supply connection.
CPT-1212-00 | 009-1276-01 | 160805
45 Perseverance Way, Hyannis, MA 02601
Copyright © 2016 Savant Systems, LLC
1 of 2
Savant.com | 508.683.2500
Component Profile Tool
Quick Reference Guide
For Product Info

RS-232 Connections
When the Profiler software is configured for RS-232, the command
codes sent from the Profiler software are sent out the RS-232 ports on
the SSC-0012 controller to the Unit Under Test (UUT). The table below
displays the pinout of the two RJ-45 connections on the controller. The
image in the table below follows the 568B format but either 568A or
568B is acceptable as long as the same standard is used on both ends
(Straight-thru).
Pin 1: (Not Used)
Pin 5: RXD (RS-232)
Pin 2: (Not Used)
Pin 6: TXD (RS-232)
Pin 3: (Not Used)
Pin 7: CTS (RS-232)
Pin 4: GND (RS-232)
Pin 8: RTS (RS-232)
Note: Pins 7 and 8 are only required for CTS/
RTS handshaking
Note: Pins 7 and 8 are only required for CTS/
RTS handshaking
IMPORTANT! When wiring to this port, DO NOT connect any wires
within the cable that are not required for communication.
RJ-45 to DB9 Adapters
When connecting between the RS-232 ports on the SSC-0012 controller
and the RS-232 port on the UUT, an RJ-45 to DB9 adapter may be
required. To make connection easy, Savant offers RJ-45 to DB9 adapters
in a variety of configurations that can be used for RS-232/422/485
control. Refer to the manufacturers support for the devices
configuration.
For information on Savant RJ-45 to DB9 adapters, see the RS-232
Conversion to DB9 and RS-422/485 Pinout application note located on
the Savant Customer Community.
IMPORTANT! If using RJ-45 to DB9 adapters not supplied by
Savant:
•Any wires required for communication/control should be
terminated within the adapter.
•Any wires NOT required for communication/control should be cut
to prevent them from shorting. DO NOT connect unused wires.
IR Connections
When the Profiler software is configured for IR, the command codes
received from the Profiler software are converted and then transmitted
out an IR port of the controller to an IR Flasher/Repeater. Connections
are made using the 6-pin Screw Down Plug-in Connectors supplied with
the CPT-1212. Connect the IR Repeater/Flasher cable by sliding the
stripped portion of each wire into the hole in the connector and locking
the wire in place by turning the screw on the top of the connector
clockwise.
IR Port Connector Pinout
Pin 1:
IR 1 -
Pin 7:
IR 4 -
Pin 2:
IR 1 +
Pin 8:
IR 4 +
Pin 3:
IR 2 -
Pin 9:
IR 5 -
Pin 4:
IR 2 +
Pin 10:
IR 5 +
Pin 5:
IR 3 -
Pin 11:
IR 6 -
Pin 6:
IR 3 +
Pin 12:
IR 6 +
Note: IR connection pairs 4 to 6 are not shown in the diagram.
GC-IRL Learner
The Global Caché IR Learner (GC-IRL) is used to capture IR commands
from 3rd Party equipment such as a remote control from the equipment
being tested. To connect the GC-IRL Learner to the MacBook (SDE),
plug the GC-IRL Learner into the Blue Adapter supplied in the CPT-1212
kit. Connect the assembly to the RS-232 port using one of the supplied
Ethernet cables.
GC-IRL IR Learner
Diagram
The Diagram below shows all the connections required when using the
CPT-1212 to test, capture, modify, or create .xml Profiles for use with
Savant RacePoint Blueprint®. Connect only what is required.
Additional Information
•The Ethernet switch/hub must be unmanaged. Features such as
setting VLANs, Spanning Tree, and SNMP could cause problems.
•Wi-Fi® must be turned offwhen working with the Profiler Software.
•If the Unit Under Test (UUT) control port is either RS-232 or IR, the
Ethernet switch/hub in the diagram does not need to be installed.
A direct connection from the MacBook (SDE) to the SSC-0012
controller will suffice.
Mounting Plate Instructions
Supplied with the CPT-1212 kit is a mounting plate (074-0577-xx) for
mounting to a wall or existing structure. This mounting plate is an option
and not required when working with the CPT-1212. However, if mounting
the SSC-0012 is required, the mounting instructions are described
below.
1. Position the mounting plate onto the wall where the controller will
be located. Orient the bracket so the mounting holes are
positioned vertically.
2. Mark on the wall the upper and lower mounting holes. Install wall
anchors and screw mounting plate to the wall.
3. Snap the SSC-0012 controller into the bracket so the tabs on the
mounting bracket seat into the slots on the side of the SSC-0012
controller.
Additional Documentation
Additional Information is available on the Savant Customer Community
•Profiler and CPT-1212 Reference Guide - 009-1292-xx
•SmartControl 12 (SSC-0012) Deployment Guide - 009-1268-xx
CPT-1212-00 | 009-1276-01 | 160805
45 Perseverance Way, Hyannis, MA 02601
Copyright © 2016 Savant Systems, LLC
2 of 2
Savant.com | 508.683.2500