Warning
Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory
operation of this product. Please retain these instructions for future reference.
Installation
Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully
note the position of each set of wires.
Note that the switch is turned off before installation.
Ensure that the screws and cable entry points are sealed to maintain the IP rating of the product.
After deciding the layout of the light fittings ensure that the cables are long enough to connect to desired positions.
The appliance must be connected to a 240 volts AC supply.
The appliance can be fitted to a rewireable 3 pin plug fitted with a 3 amp fuse.
Should the fuse require replacement, it must be replaced with a fuse rated at
3 amp and approved to BS1362.
The wires in the mains lead on this appliance are coloured in accordance
with the following code:
Wiring - Plug
Layout
Plan the desired layout of these fittings carefully, ensuring the cables will reach the distances between the junction box and the
each light fitting.
Avoid locating any cables in positions that would cause a hazard. Position cables and outdoor rated junction boxes
(not supplied) away from areas where they may be at risk from being cut, trapped or damaged.
The mains supply cable must have a minimum cross sectional area of 1.0mm2.
Cables in walls must be protected using suitable conduit or plastic trunking.
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Install in accordance with the IEE Wiring regulations and current Building Regulations.
Check the pack and make sure you have all the parts listed.
To prevent electrocution switch off at the mains supply before installing or maintaining this fitting. Ensure other persons
cannot restore the electrical supply without your knowledge.
This light fitting should be connected to a fused circuit.
If you are in any doubt, please consult a qualified electrician.
If replacing an existing fitting, make a careful note of the connections.
This system contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped.
Never put anything on the product or hang anything on any part of this product.
This product is not suitable for location in or near a marine environment.
The product will not withstand long periods of immersion in water.
The distance between the cable entry and the ground surface should be at least 10cm when installing the spike.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with
your local authority or retailer for recycling advice.
This is a Class 1 product and must be earthed.
• Decide on the position of the luminaire. Depending on the
location, an approved outdoor rated plug and socket may be
required. Alternatively an approved outdoor rated external
terminal block may be used. We recommend item
90131/90132 (outdoor rated terminal block).
• Ensure that the ground is suitable for pushing the spike
into, and can support the luminaire. Do not install in very
wet or boggy areas.
• Attach the spike to the fitting using the supplied screw and
tighten securely.
• Wire as the details wiring diagram.
• Replace fuse or circuit breaker and switch on. Your light is
now ready for use.
Bezel Bulb
(not
supplied) Supplied with
3m cable
Spike
IP65-rated
fitting
Blue – Neutral
Green / Yellow - Earth
Brown – Live
E
BROWN
Live
L
N
GREEN / YELLOW
Earth
BLUE
Neutral
FUSE
3 Amps
CORD
Clamp
If not fitting to a plug, then the product must be wired to a IP68 outdoor rated terminal block. We recommend item
90131/90132(outdoor rated terminal block).
Wiring - Terminal Block
Check that...
• You have correctly identified the wires.
• The connections are tight.
• No loose strands have been left out of the
connection block.
• Ensure that all cord grips are tightly secured.
• Ensure that all seals are re-fitted correctly.
SUPPLY
NEUTRAL
EARTH (GREEN/YELLOW)
SWITCHED LIVE
LIGHT FITTING
BLUE (N)
BROWN (L)
GREEN/YELLOW
