Saxby Lighting Equinox Bollard Manual

Instruction leaflet
Equinox Bollard
49911
www.saxbylighting.com
For your safety, always switch off the supply before changing lightbulbs, or cleaning.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities
exist. Check with your Local Authority or retailer for recycling advice.
Recycling advice
Safety information
Saxby Lighting Ltd. BH23 3PE
This bulb is protected by a shade. This part must be replaced immediately should the shade become
cracked or damaged. This fitting must not be used without the shade in place.
Replace Cracked
Shade Iss 2 27032014
When changing a bulb, always switch off at the mains
and allow the bulb to cool before handling. Dispose of
used bulbs carefully.
Do not exceed the wattage stated or use a different
shape bulb from that indicated on the fitting.
To access the bulb, simply unscrew the shade. Unscrew
the old bulb from the lampholder and replace with a new
one. Then screw the shade back in place.
Fitting/replacing bulb
Commissioning
• Pushtheterminalblockupintoofthetube.
• Standtheproductinplaceinlineoverthemounting
holes and use a suitably sized screwdriver to tighten
them so that they hold the fitting securely to the
mounting surface.
• Replacefuse or circuitbreakerandswitchon.Your
light is now ready for use.
Care and Cleaning
23W ES Energy Saver
Do not use solvents or abrasive cleaners as these could
damage the finish.
In normal circumstances, stainless steel is very resistant
to corrosion. It does however require maintenance to
preserve the high quality appearance. Wash the product
with warm soapy water, removing all surface deposits.
Rinsewithclearwaterandwithasoftcloth,wipedry.
In some cases, surface corrosion may arise after
installation. This is normally caused by tiny iron particles
left behind after the brushing process when finishing.
Wash and dry as detailed above. Then with a soft cloth
soaked with a protective oil, wipe all over.
However if the product is subject to extreme
environmental conditions such as marine locations,
industrial pollution and acid rain these maintenance
procedures should be carried out around four times a
year. For severe corrosion, non-abrasive cream cleaners
or proprietary stainless steel cleaners should be used to
remove the corrosion. Wash and dry as detailed above.
Then with a soft cloth soaked with a protective oil, wipe
all over.
Glassparts-Removeandwashinwarmwaterorjust
use a damp cloth. Do not use abrasive materials as
thesewilldamagethefinish.Glassparts-Removeand
wash in warm water or just use a damp cloth. Do not
use abrasive materials as these will damage the finish.
Do not clean the units with a pressure washer.

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and
satisfactory operation of this product. Please retain these instructions for future reference.
Warning
This is a Class 1 product and must be earthed.
Please read these instructions carefully before
commencing any work.
This unit must be fitted by a competent and qualified
electrician.
Install in accordance with IEE Wiring regulations and
currentBuildingRegulations.
To prevent electrocution switch off at mains supply
before installing or maintaining this fitting. Ensure
other persons cannot restore the electrical supply
without your knowledge. If you are in any doubt,
please consult a qualified electrician.
This light fitting should be connected to a fused circuit.
If replacing an existing fitting, make a careful note of
the connections.
Always use the correct type and wattage bulb. Never
exceed the wattage stated.
When changing a bulb, always switch off at the mains
and allow the old bulb to cool down before handling.
Dispose of used bulbs carefully and responsibly.
Waste electrical products should not be disposed of
with household waste. Please recycle where facilities
exist. Check with your local authority or retailer for
recycling advice.
This product is rated at IP44.
The entire unit gets hot whilst on for a period of time.
Specification
Voltage: 240V 50Hz a.c.
Lamp: 1 x Max. 23W E27 PL
IP rating: 44
Layout
Installation
• Planthedesiredlayoutofthisfittingcarefully,
ensuring the cables will reach the distance between
the junction box and the light fitting
• Avoidlocatinganycablesinpositionsthatwould
cause a hazard. Position cables and junction boxes
(not supplied) away from areas where they may be
at risk from being cut, trapped or damaged
• Cablesinwallsmustbeprotectedusingsuitable
conduit or plastic trunking.
• WerecommendthatyouuseH05RN-Fspecification
cable (not supplied) which is an outdoor grade,
rubber sheathed cable. The mains supply cable must
have a minimum cross sectional area of 1.0mm²
• Thesefittingmustbemountedoneitheraconcrete
surface or a paving slab that has been concreted in
position.
Existing fittings must be completely removed before
installation of a new product. Before removing the
existing fitting, carefully note the position of each set
of wires.
• Usingthebaseplateasatemplate,markthefixing
holes onto the mounting surface.
• Drillholestothenecessarysizeanddepth-taking
care not to damage any concealed pipes or wiring
below the mounting surface.
• Thisproductcomescompletewithscrewand
rawl plugs (A & B) which are suitable for use on
most surfaces, however alternative fixings may be
required.
• Pushtherawlplugsintothemountingholes.
Wiring
Having correctly identified the wiring from your existing
light fitting, pull the wire through the hole and connect
to the connection block inside the product in the
following way:
• Pullterminalblock(C)frominsideoftube.
• Unscrewthe4screwswhichattachtheblackbox
to the spacing strip. Open the black box and pull out
the terminal block.
• ConnectLiveinputwiretobrownwireonproduct
(or terminal on terminal block marked ‘L’).
• ConnectNeutralinputwiretobluewireonproduct
(or terminal on terminal block marked ‘N’).
• ConnectInputEarthwire(Green/yellow)toEarth
wire on fitting,
• Checkthatyouhavecorrectlyidentifiedthesupply
wires, the connections are tight and that no loose
strands have been left out of the connection block.
• Pushterminalblockbackintotheblackbox.
Re-attachtheblackboxtothemountingbracket.