Saxby Lighting Lille Wall Manual

• Whenchangingabulb,alwaysswitchoffatthe
mainsandallowthebulbtocoolbeforehandling.
Usedbulbsshouldnotbedisposedofwithhousehold
waste.Pleaserecyclewherefacilitiesexist.
• Alwaysusethecorrecttypeandwattagebulb.Using
theincorrectwattagebulbwilldamagethebulband
ballast.
Commissioning
Fitting/replacing bulbs
Instructionleaflet
Lille Wall
43699&43753
www.saxbylighting.com
Foryoursafety,alwaysswitchoffthesupplybeforechanginglightbulbs,orcleaning.
Wasteelectricalproductsshouldnotbedisposedofwithhouseholdwaste.Pleaserecyclewherefacilities
exist.CheckwithyourLocalAuthorityorretailerforrecyclingadvice.
Recycling advice
Safety information
SaxbyLightingLtd.BH233PE
Werecommendcleaningwithasoftdrycloth.
Donotusesolventsorabrasivecleanersasthesecould
damagethefinish.
Glassparts–Removeandwashinwarmwaterorjust
useadampcloth.Donotuseabrasivematerialsas
thesewilldamagethefinish.
This bulb is protected by a plastic shade. This part must be replaced immediately should the plastic
shade become cracked or damaged. This fitting must not be used without the plastic shade in place.
Replace Cracked
Shade
• Ensure that there are no bare or loose strands of
wire exposed, and cover all exposed areas of the
connectionblockwithtwolayersofinsulationtape.
• Refit the plastic shade, and secure using the side
screws(B).
• Refitthecover,andsecureusingscrew(A).
• Replacefuseorcircuitbreaker and switchon.Your
lightisnowreadyforuse.
Iss.230052014
18W G24d-2 2 PIN PLC

Thankyouforpurchasingthislightfitting.Pleasereadtheinstructionscarefullybeforeusetoensuresafeand
satisfactoryoperationofthisproduct.Pleaseretaintheseinstructionsforfuturereference.
Warning
This light fitting is Class 1 and must be connected to
an Earth circuit
Pleasereadtheseinstructionscarefullybefore
commencinganywork.
Thisunitmustbefittedbyacompetentandqualified
electrician.
InstallinaccordancewithIEEWiringregulationsand
currentBuildingRegulations.
Topreventelectrocutionswitchoffatmainssupply
beforeinstallingormaintainingthisfitting.Ensure
otherpersonscannotrestoretheelectricalsupply
withoutyourknowledge.Ifyouareinanydoubt,
pleaseconsultaqualifiedelectrician.
Thislightfittingshouldbeconnectedtoacircuitwitha
30mARCDfitted.
Ifreplacinganexistingfitting,makeacarefulnoteof
theconnections.
Alwaysusethecorrecttypeandwattagebulb.Using
theincorrectwattagebulbwilldamagethebulband
ballast.
Whenchangingabulb,alwaysswitchoffatthemains
andallowtheoldbulbtocooldownbeforehandling.
Disposeofusedbulbscarefullyandresponsibly.
Wasteelectricalproductsshouldnotbedisposedof
withhouseholdwaste.Pleaserecyclewherefacilities
exist.Checkwithyourlocalauthorityorretailerfor
recyclingadvice.
ThisproductisratedatIP44.
Thisproductisnotsuitablefordimming.
Thisproductisnotsuitableforlocationinorneara
marineorseaenvironment.
Theentireunitgetshotwhilstonforaperiodoftime.
TheseproductsshouldnotbefittedtoPIRcircuitsor
shortdurationtimedswitches.Shouldyouwishto
connectthisunittoatimedsystempleaseconsultthe
manufacturerbeforeinstallation.
Specification
Voltage: 240V50Hza.c.
Lamp: 1x18WG24d-2PLC
IPrating: 44
Layout
Installation
Havingcorrectlyidentifiedthewiringfromyourexisting
lightfittingandconnecttotheconnectionblockinside
theproductinthefollowingway:
Wiring
Check that...
• Youhavecorrectlyidentifiedthewires.
• Theconnectionsaretight.
• Noloosestrandshavebeenleftoutoftheconnection
block.
• Planthedesiredlayoutofthisfittingcarefully,
ensuringthecableswillreachthedistancebetween
thejunctionboxandthelightfitting
• Avoidlocatinganycablesinpositionsthatwould
causeahazard.Positioncablesandjunctionboxes
(notsupplied)awayfromareaswheretheymaybe
atriskfrombeingcut,trappedordamaged
• Cablesinwallsmustbeprotectedusingsuitable
conduitorplastictrunking.
• Themainssupplycablemusthaveaminimumcross
sectionalareaof1.0mm²
• Thisproductmustonlybefittedwiththelampholder
facingupwards.
• Thisproducthasspecialprotectionagainstthe
ingressofmoistureandisIP44rated.
Existingfittingsmustbecompletelyremovedbefore
installationofanewproduct.Beforeremovingthe
existingfitting,carefully note the position of each set
of wires.
• Undothebottomscrew(A),liftoffthetopcoverand
setaside.
• Undothesidescrews(B)andremovetheplastic
shade.
• Holdthewallbackinplaceandmarkthepositionof
theholes.Ensurethattheproductislevel.
• Ensurethewalliscapableofholdingtheweightofthe
product.Takecaretoavoiddamaginganyconcealed
wiringandpipes.Thecorrectfixingsshouldbeused
forbrick,cavitywallsorplasterboard.
• Piercegrommetandpassthesupplycablethrough
theholeinthewallback.
• Fixthewallbackintopositionusingthesupplied
screws(C).
NEUTRAL
EARTH (GREEN/YELLOW)
SWITCHED LIVE
BLUE (N)
GREEN/YELLOW
BROWN (L)
SUPPLY LIGHT FITTING
A
B