Scell-it ESSENTIAL E-312NP User manual

PNEUMATIC RIVET
NUTS SETTING TOOL
E-312NP
OPERATION MANUAL
ESSENTIAL RANGE
M3-M12
ALUMINIUM - STEEL - STAINLESS STEEL
EN

E-312NP / User manual
2
EN
TOOL CAPACITY
blind rivet nuts M3 – M4 – M5 – M6 – M8 – M10 – M12 - All materials and styles
TOOL SPECIFICATIONS
Air supply pressure : 0,5Mpa ~ 0,7Mpa
Output traction power: 21,000 N ~ 29,400 N
Stroke : 1 mm ~ 7 mm ajustable
Net weight: 1,91 kg
GENERAL SAFETY INSTRUCTIONS AND PRINCIPLES
•This tool should be used exclusively
to apply blind rivet nuts prescribed
as TOOL CAPACITY. It can’t be used
for other purposes, such as hammer,
etc…
•This tool must be used with treated
compressed air supply in a pressure
range 0.5MPa-0.7MPa.
•The tool must be, during any
kind of maintenance or repair,
DISCONNECTED from the source of
compressed air..
• DO NOT use the tool when you are
tired or under the influence of drugs,
alcohol or medication. One moment
of inattention when working with the
tool can result in serious injuries.
• DO NOT use the tool in the
environment described as below:
- fuel and combustion air.
- temperature rapidly rising.
- humidity, rain, water, storm and
thundering.
The tool is not designed for explosive
environment.
•When the tool is suspended by the
operation hook during use, be sure
the tool will not fall.
•When using the tool, always
carry safety shoes, protective
goggles, protective gloves, safety
helmet, ear protectors and other
necessary protections. It is highly
recommended for safety reason.
•Remove the setting tools or
wrenches before switching on the
pneumatic tool. A wrench connected
to a rotating part of the tool can
result in injuries.
•Do not allow persons who have not
read these instructions or who are
not familiar with the tool to use it.
•Keep children and other persons
away when you are working with
the tool. If distracted, you may lose
control over the tool.
•Have your tool repaired only by
qualified specialist personnel and
only with original spare parts. If in
doubt, always return the tool to the
distributor.
•Any alterations of the tool, its
accessories or spare parts remain in
sole responsability of the customer.
•The tool must be kept in top
condition and regularly tested for
damage and proper operation. Check
that moving parts function correctly
and do not jam and that parts are
not broken or damaged in such a
way that the function of the tool
is impaired. Have damaged parts
repaired before using the tool.
•Never aim with the tool at another
person.
•Oxygen or other flammable gasses
from pressure cylinders must not
serve as a driving agent.
•Avoid unnecessary contact with the
hydraulic fluid to prevent possible
allergy reaction of the skin.
•After the service life, discard the tool
according to the applicable disposal.
•The pressure regulator has to be
equipped with a filter to avoid
impurities and water.
READ THIS MANUAL CAREFULLY BEFORE USING THE TOOL !
It is IMPORTANT to follow the safety instructions for adequate
protection against injuries.
ENGLISH

E-312NP / User manual 3
EN
Please refer to the TOOL EXPLOSIVE ILLUSTRATION and the PARTS LIST in this manual in order to have a
good understanding of the tool parts described. The descriptions of the tool parts appear in this manual are
in italics.
1) This pneumatic powered tool should be worked with compressed air supply. It is recommended to use the air
hose with diameter bigger than 8 mm.
2) To check the compressed air pressure within the specified range between 0,5Mpa and 0,7Mpa, and to connect
the air hose adaptor onto the tool air adaptor. The air adaptor has its different versions in different countries
and areas, normally the tools are equipped with the correct version as default, in case the air adaptor does not
apply in your air supply hose adaptor, contact the tool distributor(s).
3) To change and use correct cap screw and anvil according to the size of the rivet nut to be set. This tool is
equipped with cap screws and anvils from M3 up to M12 in the tool kit. For convenience, 7 identical locknuts
provided in the tool kit for each size of the cap screw and anvil in pairs. The steel grade for the screw puller
must be 12.9.
GETTING START TO WORK
a) To remove the anvil from the tool and the locknut
(spanner from the tool kit):
c) To remove the adaptor sleeve, the screw puller,
drive bar (M3 to M8) and drive bar washer (M3 to
M8) (17mm standard spanner + spanner from the
tool kit):
b) To remove the retaining ring and nose sleeve:
d) To assemble the spring into the drive bar
(M3 to M8), the drive bar (M3 to M8) into the cap
head of cap screw, the drive bar washer (M3 to M8)
on to the cap screw and the adaptor sleeve:
f) To install the nose sleeve and screw on the retaining
ring:
g) To screw on the locknut and anvil
(spanner from the tool kit):
e) To screw on adaptor sleeve tight with spring house
with spanners (17mm standard spanner + spanner
from the tool kit):
DRIVE BAR WASHER APPLICABLE
M3-M8 USED ONLY
ADAPTOR SLEEVE
ON THE CAP SCREW
SPRING INTO DRIVE BAR, AND DRIVE BAR
INTO THE CAP HEAD OF CAP SCREW

E-312NP / User manual
4
EN
MANDREL PROTRUDING SET FOR BLIND NUT
STROKE SETTING
1) To set the length of the cap screw
protruding out of anvil according to blind
rivet nut length, by positioning of the
locknut and anvil locking each other:
1) It is very important step to define the stroke to be set on the
tool, by measuring the rivet nut and calculating in formula:
Stroke = A – ( B + C )
a) The tool stroke can be set from 1mm up to 7mm, and it shows by the indicate line pointing on to the graduation scale
precisely.
b) To increase the stroke: slide the stroke setting slider in the direction of the tool front (cap screw), turning the stroke setting
knob anti-clock wise, release the stroke setting slider back (to be sure the small needle tip seated back into the hole on the
edge of the stroke setting knob) and checking the indicate line pointing.
c) Repeat the operation until the indicate line pointing at the defined stroke; To reduce the stroke: operate in the same way but
turning the stroke setting knob clock wise.
2) Never to set the cap screw protruding length too long nor
too short according to the rivet nut to be set:
A= depth of the rivet nut (inside of the rivet nut non-threaded and no upset
part of the nut when setting)
B= total thickness of work piece(s)
C= rivet nut head thickness (if countersunk head rivet nut, then C = 0)
2) To set the stroke on the tool :

E-312NP / User manual 5
EN
TO SET RIVET NUTS
3) Checking the set stroke by initial rivet nuts setting. It is extremely important to have precise stroke setting and
trial set on work piece and refer to the illustration below to see if you got a nice set up:
1) After start-up preparations, stroke setting and initial trial setting, to put the rivet nut into work piece hole
(pre-drilled), to insert the cap screw of the tool into the rivet nut and press the button of the tool, the operation
of the rivet nut setting will be automatically finished.
2) The tool, after the button pressed, the tool will automatically insert into the rivet nut and set the rivet nut on the
work piece then released automatically.
3) If users have not had the stroke setting correctly, the tool might can not be released, then follow the process
described below to release the tool:
4) If the tool operator used a bad quality rivet nut or improper stroke setting, the tool might be blocked on the set
rivet nut and work piece and can not be released according to the above 3) described, then to use the anti-
block sticker in the tool kit, insert into the slot-shaped hole on the nose sleeve, then turning the tool with force
anti-lock wise to release the tool.
a) Slightly press the release button at the rear of the tool.
b) Press the button of the tool, then the tool will be release from the set rivet nut.
A
YES NO
B
NO
C
A
B
C
Correctly set
Not fully set
Over-set. Do not pull the nut up
too tightly as you may strip the
thread in the nut or damage the
tool mandrel.

E-312NP / User manual
6
EN
2) To connect the air supply and to cover some cloth over
the hole where the screw removed, then to press the
button and the oil will be leaked out from the tool :
3) To screw the oil inject adaptor (on oil injection tube
set in the accessories pack) into the hole where screw
removed :
4) To use the oil injection tube (in the accessories pack)
to inject the oil slowly until not able to refill, to remove
the injection tube and its adaptor, then clean the oil on
the tool and tightly screw on the screw back to the tool:
5) To test the tool stroke. If the stroke still not enough
as it should be, it means there could be some air in the
oil cylinder when you refilling the oil to the tool. Then
the extra air needs to be released from the tool.
To connect the tool with air supply, to pull the tool button 6 or 7 times,
then loosen the screw , let the extra air leaking out, then screw on the
screw tight again:
TOOL MAINTENANCE
1) To remove the screw by hexagon wrench:
If there is no lubricating device connected in the air distribution,
daily and before starting work, for better performance of the tool,
add a few drops of hydraulic oil on the inlet of the air adaptor of
the tool in order to reduce the frictions of the tool parts since the
oil will be blown inside the tool when tool operates.
After certain period of use, the tool stroke might be reduced,
it shows the hydraulic oil of the pneumatic tool is necessary
to be refilled or changed:

E-312NP / User manual 7
EN
TOOL EXPLOSIVE ILLUSTRATION

E-312NP / User manual
8
EN
The manufacturer :
Declares hereby that the following product :
Manual pneumatic hydraulic rivet nuts setting tool type E-312NPP
Complies with the following relevant conditions :
EC Machinery Directive 2006/42/EC Annex I
If the machine is modified without our knowledge and consent, this EC Declaration of
conformity will be voided
Most important applied harmonized standards :
EN ISO12100:2010 + EN ISO11148-1:2011
Name of documentation officer : Nadia FAYTRE
Address of documentation officer : see address of manufacturer
Lesquin, 30/07/2019
___________________________________________________________________
Franck DEBRUYNE
(Directeur général)
SCELL-IT
28 RUE PAUL DUBRULE
59810 LESQUIN
FRANCE
Tél.: [phone]
WARRANTY CONDITIONS
EC CERTIFICATE OF CONFORMITY – EC DIRECTIVE
2006/42/EC ANNEX II 1A
During the warranty period, the customer must not perform any alterations other than those permitted by the
manufacturer (maintenance). The repairs must be done by an authorized service center.
To admit warranty repair, the customer must return the defective tool to the service center of the manufacturer
with the proof of purchase. Warranty is valid only if the tool is in its warranty period (12 months from the date of
purchase confirmed by the proof of purchase) and if the conditions of use have been respected.
Warranty is not valid if worn spare parts have to be replaced (further to a normal use of the tool).

Scell-it UK Ltd, Unit 7, Beacon Business Park, Weston Road, Stafford ST18 0DG, UK.
TEL: [phone]
www.scellit.co.uk