Schischek ExReg-V CT Series User manual

EXPLOSIONPROOF
ExReg - V-...
ExReg - V-... - A
ExReg - V-... - B
ExReg - V- ... - CT
ExReg - V- ... - OCT
ExReg - V- ... - VA
ExReg - V- ... - OVA
...Reg-V...-CT ...Reg-V...-VA Offshore ...-OVA ExReg-V + ExMax-...-CY
www.schischek.com
Schischek GmbH Germany, Mühlsteig 45, Gewerbegebiet Süd 5, 90579 Langenzenn, Tel. [phone], Fax [phone], E-Mail [email protected]
ExReg-V_en
V02 – 23-Sep-2016
Subject to change!
Compact. Easy installation. Universal. Cost effective. Safe.
Product views and applications
Description Highlights
Electrical, explosion-proof volume flow controller (CAV / VAV)
in conjunction with ExMax-...-CY... actuators only
24 VAC/DC supply, adaptive PID controller, alarm contact
EC type-approved in acc. with ATEX directive 2014/34 /EU for zone 1, 2, 21, 22
ExReg-V Volume flow controller 0...300 Pa
Type Sensor Supply Range Connection / Interface (analogue) Alarm contact Wiring diagram
ExReg- V-300 Diff. pressure 24 VAC/DC 0...300 Pa 1 × actuator, 1 × set point Relay contact 30 V / 0.1 A SB 1.0
ExReg- V-300 - A Diff. pressure 24 VAC/DC 0...300 Pa 1 × actuator, 1 × set point, 1 × actual value, 1 × position actuator Relay contact 30 V / 0.1 A SB 1.1
ExReg- V-300 - B Diff. pressure 24 VAC/DC 0...300 Pa 1 × actuator, RS485 communication Relay contact 30 V / 0.1 A SB 1.2
ExReg- V- ... - CT Types as above with aluminium housing and seawater resistant coating (cable glands M16 brass nickel-plated, screws in stainless steel)
ExReg- V- ... - OCT Types as above, offshore version with aluminium housing and seawater resistant coating (stainless steel tubes for clamping ring connection,
cable glands M20 brass nickel-plated, screws in stainless steel)
ExReg- V- ... - VA Types as above with stainless steel housing for aggressive ambient (cable glands M20 brass nickel-plated, screws in stainless steel)
ExReg- V- ... - OVA Types as above, offshore version with stainless steel housing for aggressive ambient (tubes for clamping ring connection and screws in stainless steel,
cable glands M20 brass nickel-plated)
►For all type of gas, mists, vapours and dust for use in zone 1, 2, 21 and 22
►Power supply 24 VAC /DC
►Sensor and controller in one housing
►Direct connection of actuator to the controller’s integrated Ex-e terminal box
►No addional Ex-i module in panel required
►No intrinsically safe wiring/ installation between sensor and panel required
►No intrinsically safe wiring/ installation and no space in the panel required
►Relay output with adjustable alarm monitoring
►Scalable analogue input and output (selectable für setpoint, actual value, et al.)
►Optional analogue output for controller feedback
►Adjustable k-factor, universially applicable for any dampers
►Display with backlight, can be switched off
►Password locking
►Down to −20 °C ambient temperature applicable
►Compact design and small dimension
►Robust aluminium housing (optional with seawater resistant coating) or in stainless steel
►IP66 protection
►Offshore versions with pressure tube connection for clamping ring Ø 6 mm
The ExReg-V... flow controller is an indispensable integrant in Building
Management Control Equipment for Chemical, Pharmaceutical, Industrial
and Offshore plants for use in hazardous areas of zones 1, 2 (gas) and
21, 22 (dust).
Highest protection class (ATEX) and IP66 protection, small dimensions,
universal functions and technical data as well as an optional stainless
steel housing guarantee safe operation even in harsh environments.
ExReg-V... is used directly in hazardous areas for control of air flows in
ventilation systems. To complete the technical solution an additional
damper actuator type ExMax-...-CY or ExMax-...-CYF (with Fail Safe
spring return) is required and also a ventilation damper with orifice plate
and a known shield factor (called k-factor).
All controllers are programmable on site with menu guide. The internal
PID control structure is simple to use and automatically configured for
standard applications. The display shows the current status during
operation for the actual value, setpoint and actuator position (can be
disabled if required).
...Reg-V...-OCT and ...-OVA offshore versions are equipped with stain-
less steel tubing Ø 6 mm.
ExMax-...-CY... – see additional data sheet
NICHT freigegeben !
Volume flow controller
1 / 8

EXPLOSIONPROOF
www.schischek.com
Schischek GmbH Germany, Mühlsteig 45, Gewerbegebiet Süd 5, 90579 Langenzenn, Tel. [phone], Fax [phone], E-Mail [email protected]
ExReg-V_en
V02 – 23-Sep-2016
ExReg-V...
Special options ...-CT ...-OCT ...-VA ...-OVA
Technical data
Approbations Special solutions and accessories
...-CT Types in aluminium housing with seawater resistant coating,
parts nickel-plated
...-OCT Offshore version in aluminium housing with seawater resistant coating,
parts nickel-plated
...-VA Types in stainless steel housing, parts nickel-plated
...-OVA Offshore version in stainless steel housing, parts nickel-plated
ExMax-...-CY Control actuator, 4...20 mA Input, 0...10 V output
ExMax-...-CYF Control actuator, 4...20 mA Input, 0...10 V output with spring return
ExBox-Y/S Ex-e terminal box, 4 × M20 × 1.5 mm cable glands Ø 6 .. 13 mm
MKR Mounting bracket for round ducts up to Ø 600 mm
Kit-S8-CBR
2 cable glands M16 ×1,5 mm, Ex-e, brass nickel-plated, for cable Ø5...10 mm
Kit 2 Flexible pressure tube, 2 m, inner Ø 6 mm, 2 connection nipples
Kit-PTC-CBR 2 connecting tubes for tube fittings Ø 6 mm, stainless steel 316 L
Supply voltage / frequency 24 VAC / DC ± 15 % (20,4...27,6 VAC/DC), frequency 50...60 Hz
Current, power consumption 150 mA, ~ 3 W, internal fuse 500 mAT, without bracket, not removable
Galvanic isolation Supply for analogue in- and outputs min. 1,5 kV, supply for relay output min. 1,5 kV
Electrical connection Terminals 0,14...2,5 mm² at integrated Ex-e terminal box, stripping length 9 mm, torque 0,4…0,5 Nm, equipotential bonding 4 mm²
Cable glands 2 × M16 × 1,5 mm, Ex-e approved, for cable diameter ~ Ø 4...10 mm
Cable glands ...-CT 2 × M16 × 1,5 mm, Ex-e approved, brass nickel-plated, for cable diameter ~ Ø 6...10 mm
...-VA, ...-OCT, ...-OVA 2 × M20 × 1,5 mm, Ex-e approved, brass nickel-plated, for cable diameter ~ Ø 6...13 mm
Protection class Class I (grounded)
Display LCD matrix display with backlight, display for configuration, user guidance, parameter and actual value indication
Control elements 3 buttons for configuration
Housing material Aluminium die-cast housing, coated. Optional with seawater resistant coating (...-CT/...-OCT) or stainless steel housing,
№1.4581 / UNS-J92900 / similar AISI 316Nb (...-VA /...-OVA)
Dimensions (L × W × H) Aluminium housing ~ 180 × 107 × 66 mm, stainless steel housing ~ 195 × 127 × 70 mm (each without connectors)
Weight ~ 950 g aluminium housing, stainless steel version ~ 2,5 kg
Ambient temperature −20...+50 °C, storage temperature −35...+70 °C
Ambient humidity 0...95 % rH, non condensing
Sensor circuit Internal intrinsically safe circuit
Sensor Piezo pressure transmitter
Pressure connection P+ / P− sleeves Ø 4...6 mm. OCT and OVA versions have 2 stainless steel (316L) tube connections for clamp ring fittings Ø 6 mm
Measuring range 0…300 Pa, minimum measuring range is 2 % of full scale
Sensor damping (filter) 1...50 seconds, adjustable
Accuracy of pressure ± 2,5 % full scale ± 1 Pa
Setting zero point Via menu. Short-circuit mechanically both tube connectors P+ / P− for the moment of zero point setting
Air flow Calculation via k-factor (”shield factor”); adjustable parameters: V max, V min, V rated, k-factor
Regulation Adaptive PID controller (automatic or manual mode selectable)
Control tolerance 1...5 % adjustable
Delay time 3 s
Alarm monitoring Monitoring the volume flow; adjustable functions: tolerance limit (fixed and variable value), alarm delay
Alarm contact (terminal 3) Relay; max. values: 0.1 A (30 VAC/DC), min. values: 10 mW / 0.1 V / 1 mA
Life time mechanically 10 × 106
electrically (rated) 100 × 103
Current output (terminal 6) Range 4...20 mA, invertible, basic accuracy ± 1.0 % of full scale, load < 500 Ω, influence < 0.1 %, open circuit voltage 24 V
Voltage input (terminal 8) Range 0...10 V, invertible, basic accuracy ± 1.0 % of full scale, over-voltage up to 30 V
Voltage input (terminal 9) Range 0...10 V, adjustable, basic accuracy ± 1.0 % of full scale, over-voltage up to 30 V
Voltage output (terminal 11) Range 0...10 V, adjustable, basic accuracy ± 1.0 % of full scale, load > 10 kΩ, influence < 0.1 %, short circuit proof (type ...Reg-V300-A)
Voltage input (terminal 13) Range 0...10 V, adjustable, basic accuracy ± 1.0 % of full scale, over-voltage up to 30 V (type ...Reg-V300-A)
Wiring diagram SB 1.0 / 1.1 / 1.2
Scope of delivery Sensor, 3 self-tapping screws 4,2 × 13 mm resp. in stainless steel (with ...CT and ...VA versions), short circuit tube
ATEX directive 2014/34/EU
EC type-approved EPS 11 ATEX 1 380
IECEx certified IECEx EPS 12.0028
Approval for gas II 2 (1) G Ex e mb ib [ia Ga] IIC T6 Gb
Types ...-CT, ...-OCT II 2 (1) G Ex e mb ib [ia Ga] IIB T6 Gb
Approval for dust II 2 (1) D Ex tb ib [ia Da] IIIC T80°C Db IP66
CE identification CE №0158
EMC directive 2014/34/EU
Enclosure protection IP66 in acc. with EN 60529
2 / 8

EXPLOSIONPROOF
PA
PA
PA
5
5
5
6
6
6
7
7
7
8
8
8
10
10
10
9
9
1
1
1
11
11
2
2
2
12
12
13
13
3
3
3
4
4
4
PE
PE
PE
24 VAC/DC
24 VAC/DC
24 VAC/DC
+
~
+
~
+
~
−
~
−
~
−
~
ExReg-V300 SB 1.0
ExReg-V300-B SB 1.2
ExReg-V300-A SB 1.1
www.schischek.com
Schischek GmbH Germany, Mühlsteig 45, Gewerbegebiet Süd 5, 90579 Langenzenn, Tel. [phone], Fax [phone], E-Mail [email protected]
ExReg-V_en
V02 – 23-Sep-2016
ExReg-V...
Special options ...-CT ...-OCT ...-VA ...-OVA
The controller requires a 24 VAC / DC power supply on terminal 1(−/~) and 2 (+/~). Terminals
1 and 2 are internally connected to terminals 4 and 5 and supplies the control actuator.
(Note the actuator needs to initialize about 2 A starting current for max. 1 s). The actuator
is connected directly to the controller over terminals 4–8. If there is less than 1 meter
The ExReg-V300 is the basic version and can be used for the control of constant volumetric
flow rates (CAV) and variable flow rates of (VAV). The alarm contact (terminal 3) is used
as a feedback for normal operation, an analog feedback signal is not provided for these
devices.
The setpoint is adjusted via terminal 9. The voltage range for the minimum and maximum
flow rate is defined by a 2...10 V signal. A voltage value of about 12 V opens the damper
below 0.2 V the damper closes completely. During these forced control functions (damper
open / close) the controller is without function.
The CAV mode is configured in menu 2 by setting “CAV”. The CAV mode is activated
when the input voltage is not connected to terminal 9. In this case, the menu 7.2 “default”
set value is used as a flow. The force control functions (damper open / close) can be
applied by 0 V (close) and +24 V (open) to terminal 9. This can be done by connecting
the supply voltage level 0 V and 24 V with two relays.
The simple VAV operation in menu 2 configured via the setting “VAV”. This configuration
allows a modulation operation in a 2...10 V signal range. In the case of 2 V it is regulated
on the minimum value set in menu 5 “flow rate” and at 10 V to the maximum value. The
intermediate values are according to the voltage level (2...10 V) linearly as setpoints
available.
ExReg-V300-A is the standard version for the control of variable volume flow (VAV). The
alarm contact (terminal 3) is used as feedback for normal operation and, in addition, the
device has an analog output (terminal 11), which outputs the actual value as a continuous
signal, and an analog feedback of the actuator position (terminal 9). This feature is primarily
used for energy efficiency.
The setpoint is adjusted via terminal 13. The voltage range for the minimum and maximum
flow rate is defined as either of 0...10 V or 2...10 V.
In addition, the positive control function can be used depending on the setting in menu
6 “set point”. When the voltage value of about 12 V is exceeded the damper opens, when
it drops below 0.2 V the damper is completely closed. When utilising these force control
(damper open / close) the controller is without function. If the input is not connected, the
flow control defaults to the set value in menu 7.2.
AK: Alarm contact
Yi: Setpoint actuator 4...20 mA
Ga: Ground Y, GND
Uu: actual value actuator 0...10 V
Bus A1
Bus A2
Bus B1 Bus B2
24 VAC/DC: Supply actuator
AK: Alarm contact
Yi: Setpoint actuator 4...20 mA
Ga: Ground Y, GND
UU: actual value actuator 0..10 V
UU: Feedback actuator 0...10 V
Ga: Ground Y, GND
Ui: actual value controller 0/2...10 V
Gr: Ground controller
US: Setpoint controller
0/2...10 V
24 VAC/DC: Supply actuator
Actuator
AK: Alarm contact
Yi: Setpoint actuator 4...20 mA
Ga: Ground Y, GND
Uu: actual value actuator 0...10 V
US: Setpoint controller 0/2...10 V
Ga: Ground Y, GND 24 VAC/DC: Supply actuator
Actuator
Actuator
Galvanic Isolation 1,5 kV
Galvanic Isolation 1,5 kV
Galvanic Isolation 1,5 kV
Bus-Topologie
▪ There must be connected to a bus only point-to-point connections
▪ Star wiring is not permitted
▪ Each device works automatically as a repeater
Electrical Connection
distance between the controller and the actuator, the actuator may be connected directly
without the use of an additional terminal box. Otherwise please order terminal box (see ac-
cessories).
Attention: Before opening the terminal box cover, the supply voltage must be shut off!
3 / 8

EXPLOSIONPROOF
P− P+
ExBox
P− P+
> 1 m
!
www.schischek.com
Schischek GmbH Germany, Mühlsteig 45, Gewerbegebiet Süd 5, 90579 Langenzenn, Tel. [phone], Fax [phone], E-Mail [email protected]
ExReg-V_en
V02 – 23-Sep-2016
ExReg-V...
Special options ...-CT ...-OCT ...-VA ...-OVA
Power supply /
signal wires
Actuator
Power supply /
signal wires
Actuator
Password input
Display, buttons and parameters
The default/delivery setup is 0000. In this configuration the password input is not
activated. To activate the password protection (menu 12) change the 4 digits into your
choosen numbers (e.g. 1234) and press ENTER.
Please keep your password in mind for next parameter change! Due to a new parameter
setup the password is requested.
Display for
programming
and indication
Push button
ENTER
Push button for
level selection
Change operation – parametrisation mode
To change from operation to parametrisation mode and vice versa, push ENTER
button for minimum of 3 seconds. Back over the menu “Save” and exit.
Display in operating mode
In operating mode the current set value, the actual value and the set value are dis-
played. The red and the green LED indicate the current operating status.
When the green LED is illuminated continuously, the system is in a stable state and
indicates correct operation. If the limits of the actuator’s position are reached or an
internal fault is detected, the red LED lights up.
A flashing red LED indicates that the set point can not be achieved. The alarm func-
tion is active in this case. The yellow LEDs indicate during adjusting phase the direc-
tion of movement of the actuator. The upper LED denotes the actuator opens, the
lower LED indicates the actuator closes. The yellow LED does not flash when the
system is within the defined tolerance field (menu 12 “Controller / tolerance”).
Zero point compensation
...Reg-V-... controller are equipped with a zero point compensation to adjust the module to
the installation position. The pressure nipples P+ / P− must be connected with a short circuit
tube and the zero point compensation performed by following the menu for parametrization
(menu 3.2).
Before starting the zero point compensation, the device should be connected to power
supply for a minimum of 15 minutes to reach the uniform working temperature!
Important information for installation and operation
Installation
Hazardous area –
Zone 1, 2, 21, 22 Safe area
Control configuration
Control speed
ExMax-...-CY... – see additional data sheet
...Reg-V300 and ...-V300-A are designed for the control of volume flows. The control mode
can be set in menu 8 “Controller”. Normally, the fully automatic determination of the control
parameters (select “Auto”) is sufficient. In addition, an adaptive PID (proportional component
is calculated automatically) and a standard PID controller can be selected. These settings
should only be used by trained personnel.
In certain cases – especially in severe pressure fluctuations in the air duct – the gain of the
control loop (menu 8.2) and the control tolerance (menu 8.6) should be adjusted.
The control speed can be determined directly over the motor running time of the actuator.
The control parameters in this case must not be changed. The controller recognizes the
change automatically via the feedback signal of the actuator (terminal 7). This applies to
all controller settings. The control speed depends only on the used motor running time.
For more information see data sheet of the actuator.
A. Installation, commissioning, maintenance
All national and international standards, rules and regulations must be complied with.
For electrical installations design, selection and erection, EN/IEC 60079-14 can be
used.
Attention: Apply all Ex rules and regulation before opening the internal terminal
box. Do not open cover when circuits are live!
Draw the wiring cables through the cable glands. For connection use the internal Ex-e
approved terminal box and connect equipotential bonding.
After connection install the cables in a fixed position and protect them against mechanical
and thermical damage. Close all openings and ensure IP protection (min. IP66).
Avoid temperature transfer and ensure not to exceed max. ambient temperature! For
outdoor installation a protective shield against sun, rain and snow should be applied.
After mounting and installation a zero point compensation must be done to ensure
correct measurement results (see description).
Sensors are maintenance free. An annual inspection is recommended. For electrical
installations inspection and maintenance, EN/IEC 60079-17 can be used.
Clean with damp cloth only.
Ex sensors must not be opened and repaired by the end user.
B. Long cabling
We recommend using shielded signal wires and to connect one end of the shield to the
...Reg-... terminal box.
C. Separate ground wires
For supply and signal wires use separate grounds.
4 / 8

EXPLOSIONPROOF
www.schischek.com
Schischek GmbH Germany, Mühlsteig 45, Gewerbegebiet Süd 5, 90579 Langenzenn, Tel. [phone], Fax [phone], E-Mail [email protected]
ExReg-V_en
V02 – 23-Sep-2016
ExReg-V...
Special options ...-CT ...-OCT ...-VA ...-OVA
Menu 1 Language
Select the language
Menu 2 Application
Selection of application
2.1 VAV
Selecting standard VAV application
(factory setting)
Menu 3 Sensor
Configuration menu for sensor settings
3.1 Filter
Selection filter/damping of sensor
measurement
3.2 Zero point compensation
Short circuit P+ and P−
in final position
3.3 Status
Indication measurement value in Pa
Menu 4 Actuator
Config menu actuator
4.1 Invers
Select inverse mode
4.2 Test
Test actuator position manually
4.3 Status
Indication of position actuator
Menu 5 Air volume
Configuration menu for air volume
5.2 k-Factor
Input k-factor
5.3 V nominal
Input nominal air volume
5.4 V maximum
Input maximum air volume
5.5 V minimum
Input minimum air volume
Menu 6 Actual value
Configuration menu for actual value
6.1 Range
Select output value
6.2 Status
Indication actual value in m³/h
1: Language
English
2: Application
VAV
Device’ll be recon-
figurated. Continue?
3: Sensor
Filter
3.1: Filter
20 s
Start 0-point
compensation?
3.3: Status
87 Pa
4: Antrieb
Invers
4.1: Invers
off
4.2: Test
20 %
4.3: Status
20 %
5: Air volume
k-factor
5.2: k-factor
50
5.3: Vnom
1000 m³/ h
5.4: Vmax
800 m³/ h
5.5: Vmin
200 m³/ h
6: actual value
6.1: Range
0...10 V
6.2: Status
100 m³/ h
Deutsch, English, Français, Italiano, Espanol, back
VAV, back
no
no
yes
yes
Filter, 0-point comp., status, back
select filter time
Invers, test, status, back
off, on, back
position actuator 0 ... 100 %
k-factor, V nominal, V maximal, V minimum, back
adjust k-factor
adjust nominal value
adjust max. Value
adjust min. value
Range, status, back
0...10 V, 2...10 V, 0/2...10 V, back
Parametrisation and commissioning
Menu Function ENTER Indication Select ENTER Description
position actuator 0 ... 100 %
5 ... 300 Pa
To change from operation to parametrisation mode push “ENTER”
button for minimum 6 seconds.
If password protected: type password and push .
Back over to menu “Save” and exit.
Operation →Parametrisation
push for 6 s
5 / 8

EXPLOSIONPROOF
www.schischek.com
Schischek GmbH Germany, Mühlsteig 45, Gewerbegebiet Süd 5, 90579 Langenzenn, Tel. [phone], Fax [phone], E-Mail [email protected]
ExReg-V_en
V02 – 23-Sep-2016
ExReg-V...
Special options ...-CT ...-OCT ...-VA ...-OVA
Menu 7 Nominal value
Configuration menu for nominal value
7.1 Range
Select output value
7.2 Value
Adjust setpoint for CAV modus
7.3 Status
Indication of setpoint m³/h
Menu 8 Controller
Configuration menu for the controller
8.1 Type
Select controller type
8.2 Gain
Adjust gain of control loop
8.3 P-ratio
Adjust P-ratio
8.4 I-ratio
Adjust I-ratio
8.5 D-ratio
Adjust D-ratio
8.6 Tolerance
Adjust contoller tolerance
Menu 9 Switch
Configuration menu for the alarm relay
9.1 Alarm function
Adjust alarm function
9.2 Limit (%)
Set alarm limit in %
9.3 Limit (abs)
Set alarm limit in m³/h
9.4 Delay time
Set delay for alarm relay
Menu 10 No function
(Menu will be skipped)
Menu 11 Diagnostics
Electrical test of all in- and outputs
11.1 Input 1
Indication of status terminal 8
11.2 Input 2
Indication of status terminal 9
11.3 Input 3
Indication of status terminal 13
11.4 Output 1
Test output value terminal 6
11.5 Output 2
Test output value terminal 11
7: Nominal value
7.1: Range
0...10 V
7.2: Value
500 m³/h
7.3: Status
100 m³/ h
8: Controller
8.1: Type
Auto
8.2: Gain
100 %
8.3: P-ratio
10
8.4: I-ratio
2.0 s
8.5: D-ratio
1.0 s
8.6: Tolerance
2.0 %
9: Switch contact
9.1: Alarm function
on
9.2: Limit (%)
2.0 %
9.3: Limit (abs)
20 m³/ h
9.4: Delay time
20.0 s
11: Diagnostics
11.1: Input 1
10.0 V
11.2: Input 2
10.0 V
11.3: Input 3
10.0 V
11.4: Output 1
20.0 mA
11.5: Output 2
10.0 V
Range, status, back
0...10 V, 2...10 V, 0/2...10/12+ V, back
adjust CAV value
Type, gain, P-, I-, D, tolerance
Auto, PID adaptive, PID norm
gain 1 ... 100 %
P-ratio 1 ... 100
I-ratio 1 ... 10 s
D-ratio 0 ... 10 s
Tolerance 1 ... 5 %
Alarm function, limit %, limit abs, delay time
On, off, back
Limit 0 ... 10 %
Limit 0 ... 240 m³/h
Delay time 10 ... 200 s
Input 1, input 2, input 3, output 1, output 2, switch, back
Set 4 ... 20 mA
Set 0 ... 10 V
Menu Function ENTER Anzeige Select ENTER Description
Parametrisation and commissioning
CAV modus is automatically activ if no input signal
connected terminal 9 resp. 13 (...-A version)
6 / 8

EXPLOSIONPROOF
www.schischek.com
Schischek GmbH Germany, Mühlsteig 45, Gewerbegebiet Süd 5, 90579 Langenzenn, Tel. [phone], Fax [phone], E-Mail [email protected]
ExReg-V_en
V02 – 23-Sep-2016
ExReg-V...
Special options ...-CT ...-OCT ...-VA ...-OVA
Menu 11.6 Switch
Test relay function terminal 3
Menu 12 Password
Configuration menu for the passwords
12.1 Level 1
Level 1 password
User level
12.2 Level 2
Level 2 password
Installation level
12.3 Level 3
Level 3 password
Manufacturer level
Menu 13 Indication
Configuration menu for the indication
13.1 Display
Set display function
13.2 Contrast
Set display contrast
13.3 Brightness
Set brightness for backlight
13.4 Short menu
Use short menu
Menu 14 Parameter
Menu for parameter administration
14.1 Save
Save parameter
14.2 Use
Edit parameter
14.3 Activate
Define active parameter
14.4 Erase
Delete parameter
Menu 15 Leave menu
Leave menu and save
11.6: Switch
Function: open
12: Password
12.1: Level1
0000
12.2: Level 2
0000
12.3:Level 3
0000
13: Indication
13.1: Display
on, lighted
13.2: Contrast
60.0 %
13.3: Brightness
100 %
13.4: Short menu
off
14: Parameter
14.1: Save
P1 (active)
14.2: Use
P1 (active)
14.3: Activate
P1 (occupied)
14.4: Erase
P1 (occupied)
Function open / close status open / close
Level 1, level 2, level 3, back
Password
Password
Password
Display, contrast, brightness, short menu, back
On lighted, on, off, back
0 ... 100 %
0 ... 100 %
On, off, back
Save, use, activate, erase, back
P1, P2, P3, back
P1, P2, P3, back
P1, P2, P3, back
P1, P2, P3, back
Parametrisation and commissioning
Menu Function ENTER Indication Select ENTER Description
15: Leave menu
Back, yes
Short menu „on“ reduces the parameterization to a minimum.
Detail settings are not possible.
Save up to 3 different parameters to test the controller.
7 / 8

EXPLOSIONPROOF
69
81.3
126.3
Ø 4.5
182.7 181.7 2
4.5
~ 61
70
102
~ 226
123.3
~ 194
59
21.5
...Reg-V...-OCT
68
157,5
117
138
166
80
107
55
66
~ 180
Ø 4,5
Ø 4,5
Ø 4,5
170
213
...Reg-V...-OVA
www.schischek.com
Schischek GmbH Germany, Mühlsteig 45, Gewerbegebiet Süd 5, 90579 Langenzenn, Tel. [phone], Fax [phone], E-Mail [email protected]
ExReg-V_en
V02 – 23-Sep-2016
ExReg-V...
Special options ...-CT ...-OCT ...-VA ...-OVA
Dimensions [mm]
Aluminium housing
Stainless steel housing
8 / 8