Schlage BE365 User manual

Installation Instructions
BE365
P515-481
A. Keypad Assembly
B. Deadbolt
C. Mounting Plate
D. 9V Battery
E. Mounting Screws
F. Thumbturn Assembly
G. Thumbturn Screws
H. Deadbolt/Strike Screws
J. Strike
K. Dust Box
L. Reinforcement Screws
M. Reinforcement Plate
N. Rounded-corner Faceplate
P. Square-corner Faceplate
Q. Drive-in Faceplate
Install Lock
Remove Template From Programming Booklet
1
OR
Tools for Installation
E
D
F
B
C
A
H
G
J
K
L
M
2Check Door Holes
Note: If door holes do not match template, visit
www.schlage.com for door drilling instructions.
QP
N
2
A. Key
1.Turnson the backlight.
2.Indicates lock status (programming
mode,low battery,etc.)and success
or failure of an operation.
3. Confi
rms a menu entry during
programming (see page 8).
4.U
sed to exit programming or to clear
an incorrect entry.
B.Keypad
1.U
sed to unlock the lock byentering a
valid four-digituser code.
2.U
sed to program the lock.
(See page 8.)
C. KeyOverride (See page11.)
Used to unlock the lock in the following
situations:
1. Lock has failed electronically.
2.Battery is dead.
3. User code is not known.
D.Outside Knob/Lever
To minimize damage from vandalism,
the outside knob/leverrotates but does
not retract latch evenwhen lock is
locked.
E.Inside Knob/Lever
The inside knob/lever is always
unlocked forimmediate exit.
FE575 Features
A. Key
B. Keypad
C.KeyOverride
D.O
utside Knob/Lever
E.Inside Knob/Lever
2³⁄₈”(60mm) To Door Edge
CUT HERE
2³⁄₄” (7 0mm) To Door Edge
1⁵⁄₈"
For 1³⁄₈"
Thick Door
For 1³⁄₄"
Thick Door
⁷⁄₈”
(22 mm)
Hole
Template for FE575, FE595,BE365
ForUse With
OR
2¹⁄₈”
(54 mm)
Hole
OR
Match to Door Edge Door Edge
2³⁄₈”or 2³⁄₄”
R
o
t
a
t
e
T
e
m
p
l
a
t
e
t
o
M
a
t
c
h
D
o
o
r
5¹⁄₂”
Minimum
2³⁄₈” (60mm)ToDoor Edge
R
o
t
a
t
e
T
e
m
p
l
a
t
e
t
o
M
a
t
c
h
D
o
o
r
2³⁄₄” (7 0mm)ToDoor Edge
OR
2¹⁄₈”
(54 mm)
Hole
2³⁄₈”or 2³⁄₄”
Door Edge
Te m plate for FE575, FE595,BE365
For1³⁄₈"
Thick Door
For1³⁄₄"
Thick Door
1⁵⁄₈"
⁷⁄₈”
(22 mm)
Hole
For Use With
OR
Match toDoor Edge
CUT HERE
Keep the programming
booklet with you while
installing lock. Without
the user codes, you can
get locked out.
STOP

For U.S.A.– Choose Appropriate Deadbolt
For Canada– See bottom of page.
3
2³⁄₈”
OR
2³⁄₄”
For Canada ONLY: If Needed, Adjust Deadbolt
OR
2³⁄₈”2³⁄₄”
Move to Step 4
Rotate Faceplate 180°
Actual Size
Actual Size
Rounded Corner
Use
Move to Step 5
Choose Deadbolt Faceplate
4
Install Deadbolt
IMPORTANT: Make sure “top” is pointing up.
5
Square Corner
Install
Drive-in
Install
Actual Size
Wood Block
(Not included)
OR
OR
OR
To p
To p

67Install Inside Mounting Plate
IMPORTANT: Pull excess wire through mounting plate.
Install Keypad Assembly
IMPORTANT: Cable passes over top of deadbolt.
8Check Cam Orientation and Install Screws
Actual Size
Cam tip MUST
point down
Deadbolt MUST
be retracted
STOP

Install Battery and Connect Cables Install Thumbturn
9 11
©2006 Schlage Lock Company
Printed in U.S.A.
P515-481 Rev. 6/06 CD
Route and Tuck Cables
IMPORTANT: Cable must be routed and tucked as shown.
10 Install Strike, Dust Box and Reinforcer 12
Actual Size
Actual Size
Point away
from door edge
Door Edge
Actual Size
ab
cd