Schlage CO-100 User manual

CO-100
OFFLINE LOCK USER GUIDE
INSTRUCTIONS FOR CORE SERIES OFFLINE LOCKS
Para el idioma español, navegue hacia www.schlage.com/support.
Pour la portion française, veuillez consulter le site www.schlage.com/support.
P516-270

2
CO-100 Offline Lock User Guide
CONTENTS
Overview........................................................................................................................................ 3
Getting Started .............................................................................................................................. 4
Construction Access Mode............................................................................................................ 4
Manual Lock Programming ........................................................................................................... 5
Credential Types........................................................................................................................ 5
Programming Legend ................................................................................................................ 5
Manual Programming Commands............................................................................................. 6
Using the Lock............................................................................................................................... 7
Error Codes ................................................................................................................................... 7
Testing ........................................................................................................................................... 7
Mechanical Testing .................................................................................................................... 7
Electronic Testing ...................................................................................................................... 7
Resetting To Factory Defaults........................................................................................................ 8
Batteries ....................................................................................................................................... 9
Installing or Replacing Batteries................................................................................................ 9
Low Battery Indications ............................................................................................................. 9
Battery Failure Mode ................................................................................................................. 9
LED Reference ............................................................................................................................ 10
Schlage Button ........................................................................................................................ 10
Optional Inside Push Button (IPB)........................................................................................... 10
Troubleshooting ........................................................................................................................... 10
FCC Statements.......................................................................................................................... 10
www.schlage.com/support
877.671.7011

3
CO-100 Offline Lock User Guide
OVERVIEW
The Schlage CO-100 is an off-line electronic lock in the CO-Series product line.
• Two factory-configured functions are available: 1) Classroom/Storeroom, and 2) Office.
• The lock is powered by four (4) AA batteries. See Batteries on page 9 for more information.
• Outside lever is normally locked.
• Inside lever always allows egress.
Outside
Schlage Button
Outside Lever
Keyway
Inside
Thumbturn
Battery
Compartment
Inside Push
Button
Inside Lever
Keypad
CO-100-CY
CO-100-MS
CO-100-MD CO-100-993

4
CO-100 Offline Lock User Guide
GETTING STARTED
Follow these steps when setting up a new lock.
1. Install the lock. See the installation guide that came with the lock, or visit
www.schlage.com/support, for more information.
2. Test the lock for proper mechanical and electronic operation. See Testing on page 7 for more
information.
3. When ready to set up for normal use, enter a new programming code, then program the user
credentials. See Manual Lock Programming on page 5-6 for more information.
4. Familiarize yourself with the information in this guide.
! Save this user guide for future reference.
CONSTRUCTION ACCESS MODE
Construction Access Mode is used to allow access before the lock has been programmed, and for
testing purposes. Construction Access Mode is enabled by default.
Offline locks with keypads, have a default PIN of 13579
and “#”, which can be used for installation, testing and
construction access.
• To test, enter the default PIN (13579 and “# ”).
• The Schlage button will blink and the lock will unlock.
• The default PIN is automatically deleted when a new
programming credential is created.
TIP
If you press the Default PIN code on a
new lock and the code is not accepted,
the lock has already been programmed.
If the new PIN is not known, or to put
the lock back into construction access
mode, reset the lock to factory settings.
See Resetting To Factory Defaults on
page 8 for more information.

5
CO-100 Offline Lock User Guide
MANUAL LOCK PROGRAMMING
Left LED Right LED
Credential Types
Credential Type Function Description Default PIN
Programming Used to program the lock – does not
unlock the lock Five-digit code 97531 and
Normal Use Unlocks the lock PIN (3 - 6 digits) 13579 and
Toggle Changes the state of the lock unless in
Freeze state PIN (3 - 6 digits)
Freeze Maintains the lock in current state until
Freeze PIN is entered again PIN (3 - 6 digits)
Pass-Through Unlocks a lock momentarily, regardless
of state PIN (3 - 6 digits)
Programming Legend
Symbol Description
[Programming Code]1Five-digit code, identical to programming credential
code listed in the Credential Types table.
[PIN] Three- to Six-digit code. A PIN can be any of the PIN
code types listed in the Credential Types table.
Asterisk key on the keypad
- Number keys on the keypad
Schlage button
1 Programming codes such as 1-1-1 or 1-2-3-4 can be easily selected by non-authorized
users and should not be used.
TIP
Use the same
programming code
for all locks in the
facility.

6
CO-100 Offline Lock User Guide
Manual Programming Commands
Commands are confirmed by five alternating green blinks of the Schlage button.
The right LED on the Schlage button will blink green to indicate an incorrect entry. To interpret
blink patterns, refer to Error Codes on page 7.
Function Press
Wait For
Confirmation1
Change
[Programming Code]
[Programming Code] Wait for
to stop flashing
between each
step.
New [Programming Code]
New [Programming Code]
Add Normal Use
PIN
[Programming Code] Wait for
to stop flashing
between each
step.
New [PIN]
add another PIN OR to finish
Add Toggle PIN
[Programming Code] Wait for
to stop flashing
between each
step.
New [PIN]
add another PIN OR to finish
Add Freeze PIN
[Programming Code] Wait for
to stop flashing
between each
step.
New [PIN]
add another PIN OR to finish
Add Pass-Through
PIN
[Programming Code] Wait for
to stop flashing
between each
step.
New [PIN]
add another PIN OR to finish
Delete a PIN
[Programming Code] Wait for
to stop flashing
between each
step.
[PIN] to be deleted
to finish
Change Relock
Time
[Programming Code] Wait for
to stop flashing
between each
step.
to add 1 second AND/OR to add 5 seconds
to finish
Disable/Enable
Beeper
[Programming Code] Wait for
to stop flashing
between each
step.
to disable beeper OR to enable beeper
1 Other lights may show before the final confirmation. Wait for final confirmation before continuing to the next step.

7
CO-100 Offline Lock User Guide
USING THE LOCK
After PIN credentials have been programmed, enter a PIN to operate the lock as follows:
Credential Action
Press a valid PIN Green LED will blink and access granted
The “#” key is used as ENTER key for PINs with fewer than six digits.
If the PIN credential is entered incorrectly, press “*”to start over.
ERROR CODES
All error codes are indicated on the Schlage button by a solid red LED and a blinking green LED.
The number of green blinks indicates the error code.
Number of
Green Blinks Error Code Description
1 Computer programming error (not complete).
2 Too long user/master code entered. Code length cannot exceed 8 digits.
3 Memory full, too many codes. Delete some codes.
4 Master code cannot be deleted, only changed.
5 Master code entries do not match. Master code not changed.
6 Invalid command. Invalid function code entered.
7 Code not found.
8Code too short. Minimum master code length is five (5) digits, minimum user code
length is three (3) digits.
9 Not a unique code.
10 Manual programming not allowed.
TESTING
If you encounter problems while performing any of the following tests, review the installation guide
and correct any problems.
Mechanical Testing
1. Rotate the inside lever or depress the push bar to open the door. Operation should be smooth,
and the latch should retract.
2. Insert the key into the keyway and rotate the key and the outside lever to open the door.
Operation should be smooth, and the latch should retract.
Electronic Testing
1. Press any number key. The lock will beep. Use the default PIN (13579 and “#”) to verify access.
Error code functions have not been verified by Underwriters Laboratories Inc.

8
CO-100 Offline Lock User Guide
RESETTING TO FACTORY DEFAULTS
! All information in the lock will be deleted and reset to factory defaults!
In the factory default reset state, offline locks have a default PIN of 13579 and “#”, which can be used
for installation and testing.
Follow these steps to reset to factory defaults.
1. Remove the top inside cover.
2. Remove one battery from the battery pack to disrupt power. Wait 5 to 10 seconds for power to run
out in the lock.
3. Press and hold the Schlage button while reconnecting the battery
into the battery pack to resupply power.
4. Continue holding the Schlage button, and wait for two beeps to
sound and two green blinks of the Schlage button.
5. Release the Schlage button.
6. Press and release the Schlage button three (3) times within 10
seconds of the beeps and blinks at step 4. One beep will sound and
one red blink will occur with each press.
7. The Schlage button will light green for one second and a one-second
beep will sound, indicating that the lock has been reset.
If the Schlage button is not pressed 3 times within 10 seconds,
two beeps and two red blinks indicate timeout.
8. Replace the top inside cover.
To test, enter 13579 and “#”. The Schlage button will blink and the lock will unlock.
TIP
If the Schlage button is
not pressed and held
while reconnecting the
battery, then the lock
is ready for normal
operation (as after a
power-on reset).

9
CO-100 Offline Lock User Guide
BATTERIES
Installing or Replacing Batteries
1. Remove the battery cover.
2. Remove the Battery Bracket.
3. Install the new batteries. Observe polarity. (Install only new AA Alkaline batteries.)
4. Install the Battery Bracket.
5. Connect the batteries.
6. Reinstall the battery cover.
! CAUTION! Danger of explosion if batteries are incorrectly replaced! Replace only with
new AA alkaline batteries. Dispose of used batteries according to the manufacturer’s
instructions.
CY, MS, & MD 993
!Plug MUST Be on Right
Low Battery Indications
Changing batteries does not affect any programmed data.
Condition Indicator Solution
Batteries Low After credential PIN is pressed, 9 red
blinks of Schlage button, then normal
indicator.
Replace batteries immediately to
avoid battery failure. Lock is intended
to operate for 500 cycles in low
battery condition.
Battery Failure No LED or beeps
Valid credentials do not grant access
Replace batteries immediately.
Mechanical override key must be
used to unlock lock.
Battery Failure Mode
In the event of battery failure, the lock will fail As-Is (lock remains in current state, locked or unlocked,
until batteries are replaced).

10
CO-100 Offline Lock User Guide
LED REFERENCE
Schlage Button
Condition Lights
Access denied 2 red blinks
Factory default reset One-second solid green with one-second beep
Low battery indicator, AA batteries 9 left red blinks
Momentary unsecured access 1 green blink, then one red blink on relock
Optional Inside Push Button (IPB)
Action Lights
Office Mode
Press IPB to lock 1 red blink
Press IPB to unlock11 green blink
1 Unlocking the lock with the IPB will cause the lock to remain unlocked until the IPB is depressed again.
TROUBLESHOOTING
For troubleshooting, visit to www.schlage.com/support.
FCC STATEMENTS
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired
operation.

11
CO-100 Offline Lock User Guide

© 2010 Ingersoll-Rand Company
P516-270 ENG online Rev. 08/10-b