Schwinn Tone 1 Owner's manual

Important Handlebar Grip Replacement Supplement
Refer to the tone owner’s manual that came with your product for complete warnings and instrucons.
Parts
Included
Remove the EXISTING
handlebar grips
❶ Remove both exisng grips (1a and 1b)
by turning the le grip counter-
clockwise and the right grip clockwise.
❷ Remove both washers (2a and 2b).
❸ Loosen the hex screws (3a and 3b) on
both thumb levers.
❹ Remove the thumb levers (4a and 4b)
from the handlebar.
AachtheNEW
handlebar grips
❶Slide the new clamps
(1a and 1b) onto each side
of the handlebar.
❷ Route the wires (2a and 2b)
into each clamp slot.
❸Slide the thumb levers
(3a and 3b)onto each side of
the grips.
❹Insert the new grips
(4a and 4b) completely
through the thumb levers
and clamps.
R
R
L
L
LThin side
faces in
Thick side
faces out
Thin sideThick side
3 mm
4 mm
5 mm
Clamps
Hex key Replacement handlebar grips
View from underside of the handlebars
Note: Discard the washers,
and exisng grips, they are
no longer needed.
Aer
Before
Rotate the left grip
clockwise and the right
grip counter-clockwise
until fully tightened.
❺Confirm the L and R sticker
(5a and 5b) on the end of
each new grip matches the
correct side.
❻Tighten the hex screws
(6a and 6b) on the clamps
using the 4 mm hex key.
❼Tighten the hex screws
(7a and 7b) on the thumb
levers using the 3 mm
hex key.
R
WARNING! Grips may loosen or fracture and may cause lose of control if the grips are not replaced!
1a
1a
3a
3a
2a
4a
4a
4b
4b
5a 5b
2a
6a 6b
7a 7b
2b
1b
1b
3b
3b
2b

© 2021 Pacic Cycle Inc.
4902 Hammersley Rd.
Madison, WI 53711
Remove the EXISTING handlebar grips
❶ Remove both exisng grips (1a and 1b)by turning the
le grip clockwise, and the right grip counter-clockwise.
❷ Remove both washers (2a and 2b).
❸ Loosen the hex screw on the thumb lever and remove
the thumb lever.
❹Loosen the hex screw on the hand brake and remove the
hand brake.
AachtheNEWhandlebargrips
❶ Slide the new clamps (1a and 1b) onto each side of the
handlebar until it meets the center control panel.
❷ Route the wire into the clamp slot.
❸ Slide the thumb lever onto the right-hand grip until it meets
the clamp.
❹ Slide the hand brake onto the left-hand grip until it meets
the clamp.
❺ Insert the new grips (5a and 5b) completely through the
brake and clamps. Rotate the left grip clockwise and the
right grip counter-clockwise until fully tightened.
❻ Confirm the L and R sticker (6a and 6b) on the end of each
new grip matches the correct side.
❼ Tighten the hex screws (7a and 7b)on the clamps using the
4 mm hex key.
❽Tighten the hex screw in the thumb levers using the 3 mm
hex key.
❾Tighten the hex screw in the hand brake using the 5 mm
hex key.
Note: Discard the washers,
and exisng grips, they are
no longer needed.
R
L
❸
❸
❽
❷
❹
❾
R
L
Thin side
faces in
Thick side
faces out
❹
❸
Aer
Before
1a
1a
2a 2b
1b
1b
5a 5b
6b
7b
7a
6a