Screen Int MODIGLIANI Oyster User manual

INSTALLATION MANUAL
FRAME SCREEN
MODIGLIANI Oyster
MODIGLIANI VELVET Oyster
ORIGINAL INSTRUCTIONS IN ITALIAN LANGUAGE
Translation into English language

RELEASE ER2021_07_19
Mod. MODIGLIANI/MODIGLIANI VELVET
COMPONENTS INSIDE THE PACKAGING
Frame segments (A)
Projection surface (C)
Mounting brackets (E)
Steel edges with screws (B)
Rubber band (D)
Screws and wall plugs (F)
PCS. 04
PCS. 01
PCS. 02
PCS. 04
PCS. 04

RELEASE ER2021_07_19
Mod. MODIGLIANI/MODIGLIANI VELVET
INTRODUCTION
Thank you for purchasing a frame screen among the range Modigliani and Modigliani Velvet. This
screen is made entirely in Italy with rst-class materials, including a high quality projection surface to
guarantee excellent performance for your installation.
WARNINGS
Before installing the screen, please read the following instructions carefully. We would recommend
that these instructions are stored safely for future reference. When opening the packaging of the
screen, please DO NOT USE CUTTERS or OTHER SHARP TOOLS that can damage the screen
inside. During opening the packaging and during installation, it is reccomended to use work gloves.
Depending on the screen weight, it has to be handled by at least two or three persons taking care
to the following ratio KG/PERSON: MALE 25 kg. – FEMALE 15 kg.
Take care to mount the screen in the room with 20°C - 24°C temperature.
The manufacturer does not take responsibility for any damage to property or personal injury if the
screen is used outside of recommended specications or in case of incorrect/poor quality installation.
CERTIFICATIONS
Modigliani and Modigliani Velvet are CE certied.
WARRANTY
This projection screen is guaranteed 2 years from the purchase date for manufacturing defects.
Responsibility is limited to repairing or substitution of the defected components and without any
other charge at our expense.
Warranty is ofcially voided if the screen has been dismantled or it is returned with collision damage
or defective due to incorrect installation. Repairs must be carried out by an Approved ScreenInt
Certied Engineer.
Warranty is ofcially voided if (all the following cases are including but not limited): 1) defects not due
to deciencies in the material or workmanship;
2) amendments, alterations, repairs or disassembling of the Product not previously authorized in
writing by Screenint;
3) installation, use or maintenance of the Product not in compliance with Screenint‘s instructions as
set forth in this Installation Manual and/or in any other technical documentation supplied together
with the Product;
4) bad and/or improper and/or not in compliance installation, maintenance, negligence, improper
use;
5) use of non-original spare parts or not authorized in writing by Screenint;
6) normal wear and tear;
7) the screen has been damaged in transit;
8) the sticker regarding the serial number of the product has been altered, deleted, removed or
tampered.
DO NOT install this screen nearby or over heating or air conditioning systems, because PVC is a
plastic material which dilates and remains damaged if it is subjected to heat and/or cool air.
DO NOT install this screen either facing direct sun light or blocking a window as PVC could be
damaged and make waves for the explanations given above.
The PVC cloth is very sensitive to temperature range. We advise to mount the screen in environments
with an ambient temperature in the range of 20°-25°C. We advise you to WAIT 3 HOURS for the
SCREEN to ACCLIMATISE BEFORE MOUNTING the screen after delivery, especially if screen arrives
from a cold temperature.
THE SCREEN HAS TO BE STOCKED AND TRANSPORTED ALWAYS IN HORIZONTAL POSITION,
otherwise there could appear waves on the projection cloth.
DO NOT WASH the projection surface with alcohol or solvent nor with commercial cleaners. Every
now and then dust the surface with a dry and clean duster. Please, be very careful because any kind
of stain on projection surfaces is inerasable.
When the screen is not completely rolled down (as by factory setting), atness of the cloth is NOT
guaranteed and therefore not covered by warranty.
DO NOT HANG TO THE SCREEN and DO NOT HANG ANY OBJECT to it. Please take care that
children DO NOT PLAY with the screen as they can get severely injured.
The manufacturer will not accept returns of screens for repair without manufacturer’s authorization
(RMA number) and without a suitable packaging.

RELEASE ER2021_07_19
Mod. MODIGLIANI/MODIGLIANI VELVET
INSTALLATION INSTRUCTIONS
1. FRAME ASSEMBLY
The product has to be installed and used conform to the laws in force within the country where the
product is used. Lay the frame segments (A) on the oor with the anchoring cursors facing upwards; in
order to avoid scratches to the frame we advise you to lay the frame on a soft and clean cloth.
Connect the base and height segments using the supplied steel edges (B) in order to make a rectangle
(Fig. 1.1); tighten the screws on the edges, in order to make four 90° angles (Fig. 1.2). Check that the
dimensions of L1 and L2 are the same.
2. PROJECTION SURFACE ASSEMBLY
THE PROJECTION SURFACE OYSTER IS EXTREMELY DELICATE. IT
HAS TO BE HANDLED WITH CARE, AVOIDING TO BEND IT AS IT
WOULD BE DAMAGED PERMANENTLY.
Lay the frame with anchoring cursors facing upwards. Put the projection surface (C) on the frame, with
the reecting side facing downwards and be careful not to get it dirty or to scratch it.
In order to tight the screen surface (C) put the rubber bands (D) into the holes and hook them to
the cursors (see Fig.2.2 till Fig. 2.6) TAKE CARE TO START FROM THE OPPOSITE FOUR ANGLES
(Fig. 2.1).
3. WALL MOUNTING
The frame has to be mounted to the wall using the two upper frame brackets supplied (E).
The brackets have to be xed to the wall using the screws and wall plugs (F) supplied. Before drilling
the wall, please check the brackets will be positioned as follows:
- Upper left bracket: has to positioned between second and third frame cursor at the left side (Fig. 3.1);
- Upper right bracket: has to positioned between second and third frame cursor at the right side (Fig.
3.1);
In order to x properly the frame, please consider carefully the measures indicated in (Fig. 3.2).
Once the upper brackets are xed to the wall, position the frame as shown in Fig. 3.3 – Fig. 3.5
Do not tilt the frame forward or backwards otherwise the manufacturer cannot guarantee the atness
and the squareness of the frame.
Squareness of the frame is not guaranteed in case the screen is mounted in different ways (e.g. metal
chains from the ceiling ) from what is written above.
At the end of the installation, please check that the frame is perfectly levelled.
CAUTION: CHECK EVERY 6 MONTHS THAT SCREWS WALL PLUGS AND BRACKETS ARE IN
GOOD CONDITIONS AND WELL TIGHTENED.
DO NOT STAY UNDER THE PROJECTION SCREEN.
IT IS NOT SUITABLE FOR OUTDOOR USE.

RELEASE ER2021_07_19
Mod. MODIGLIANI/MODIGLIANI VELVET
L1
L2
Fig. 1.3
L1 = L2
Fig. 1.1 Fig. 1.2

RELEASE ER2021_07_19
Mod. MODIGLIANI/MODIGLIANI VELVET
Fig. 2.1
Fig. 2.2
Fig. 2.4
Fig. 2.6
Fig. 2.3
Fig. 2.5

RELEASE ER2021_07_19
Mod. MODIGLIANI/MODIGLIANI VELVET
46
88
32
42
45
90
3510
15,5
75,5
5,5
105
Max M5
46
88
42
Fig. 3.1
1 12 23 3
Fig. 3.2 Fig. 3.3
Fig. 3.4 Fig. 3.5

RELEASE ER2021_07_19
Mod. MODIGLIANI/MODIGLIANI VELVET