SECO-LARM ENFORCER SD-962AR-36M User manual

11/16”
(18mm)
Installation Manual
SD-962AR-36M
Modern Flat Rim-Type Exit Bar
Features:
What It Does:
SECO-LARM’s SD-962AR-36M exit device, when mounted on the inside of a door to block entry to a protected premises,
securely locks the door from outside access while allowing users inside the protected premises to exit. The hardy
aluminum enclosure protects the exit device from abuse, yet easily unlocks the door from the inside by users who require
exit. It can be connected to a rim cylinder lock on the outside of the door in order to allow entry by authorized personnel.
Dimensions:
31/8”
(80mm)
Sturdy aluminum construction.
Allows exit from inside while locked from outside.
Reversible non-handed design.
For metal or wood doors up to 13/4” thick.
Includes all needed hardware for typical
installation.
Works with rim cylinder locks (not included).
Fits doors from 36” to 48” wide.
351/8” (892mm)
71/2”
(190mm)
25/8”
(67mm)
15/8”
(42mm)
22”
(559mm)

ENFORCER Modern Flat Rim-Type Exit Bar
2SECO-LARM U.S.A., Inc.
Fig. 3 –Possible Applications
Fig. 2 –Parts Description
Chassis cover
Chassis
Mechanism housing
Push bar
Dogging device –
Use Allen key to lock
in the open position
so the door can be
opened from outside
the protected
premises.
End cap
Strike
End cap bracket
Single Door
Double Door
with Mullion
Double Door
without Mullion
Door
Exit device
17/16”
Rim Cylinder
Rim Cylinder
Rim Cylinder
Door
Door
Exit device
Exit device
17/16”
Double-door strike
(not included)
Rim Cylinder
Rim Cylinder
Rim Cylinder
17/16”
Door
Exit device
Door
Exit device

ENFORCER Modern Flat Rim-Type Exit Bar
SECO-LARM U.S.A., Inc 3 SECO-LARM U.S.A., Inc. 33 3
Fig. 4 –Mounting
Location
Fig. 5 –Using the
Template
Fig. 6 –Mounting the
Strike
Door
Draw line here
41”
Fig. 7–Final Installation
1. Mark the vertical center line of the exit bar by drawing a line across the door at 41” above the floor.
See fig. 4.
2. Fold the included template, and align the center lines on the template with the center line just drawn on
the door. Then mark the position of the mounting holes for the latch assembly. See fig. 5.
3. Move the template against the door stop and then mark the mounting holes for the strike.
4. Drill the holes as marked on the door and the mullion. See fig. 6.
Toothed lock
washer
Toothed lock
washer
Hex nut
Hex head
screw

ENFORCER Modern Flat Rim-Type Exit Bar
4SECO-LARM U.S.A., Inc.
Specifications :
Construction
Aluminum
Hand
Non-handed
Latch bolt
Steel 19mm throw
Spring
Stainless steel
Chassis
Aluminum
Cover
Aluminum
Rail assembly
Aluminum
End cap
Aluminum
Dimensions
351/8”x71/2”x25/8” (892x190x67 mm)
Weight
6-lb, 7-oz (2.9kg)
WARNING: Incorrect mounting that leads to exposure or moisture inside the enclosure could damage the device and will void the warranty.
PITDW1
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a period of one (1) year from the
date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned,
transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal
usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in
material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damages of any kind to the
purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is one of continual development and
improvement. For this reason, SECO-LARM reserves the right to change specifications without notice.
SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2011 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of
SECO-LARM.
SECO-LARM U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: [phone]
Website: www.seco-larm.com
E-mail: [e-mail]
MiSD-962AR-36I_1107.docx
Parts List:
1xRim-Type Exit Device
1xManual
3 x Mounting templates
Screws Included:
1xEnd cap bracket
1xPlate spacer for strike (3.2mm)
1xPlate spacer for strike (1.6mm)
1xStrike
1xEnd cap
1xHex wrench
Mounting chassis to door:
2 x Hex head screws (for the outside holes)
2 x Hex nuts (for the outside holes)
4 x Mounting screws (for the inside holes—wood doors)
4 x Mounting screws (for the inside holes—metal doors)
4xToothed lock washers (for the inside holes)
Connecting cover to chassis:
2 x Set screws
Connecting end cap to end cap bracket:
2xSet screws
Mounting end cap bracket to door:
2 x Mounting screws (wood doors)
2 x Mounting screws (metal doors)
4 x Toothed lock washers
Mounting strike to door:
2 x Mounting screws (wood doors)
2 x Mounting screws (metal doors)
2xToothed lock washer