Securam ScanLogic B22 User manual

ScanLogic B22 Operation Instructions
Model No: FPC-1701A-B22-II
Version No: V1.0
1.0 System Installation
1.1 System Components
1.2 Pairing the EntryPad with the Lock
1.3 Lock and EntryPad Installation
1.4 Installing Battery
1.5 Test Lock Operation
2.0 Lock Operation
2.1 Opening the Lock
3.0 Set Date and Time
3.1 Set Clock Time
4.0 Code/Fingerprint Management
4.1 Change Code
4.2 Enroll Manager 2
4.3 Enroll New User
4.4 Delete One User
4.5 Delete All Users
4.6 Add Finger
4.7 Delete Finger
5.0 Smartphone Management
5.1 Pair Phone
5.2 Delete Phone
6.0 System Identification
6.1 System Info
7.0 Lock Settings
7.1 Factory Reset (Firmware)
7.2 Show Audit Trail
7.3 Enable/Disable Vibration Sensor
7.4 Security Level
7.5 Set Vibration Sensitivity
7.6 Set Battery Efficiency
8.0 Data Management
8.1 Encryption Key Set
9.0 Recovering the System –Reset to Default
9.1 Recovery Code Set
9.2 Recover System
9.3 Mechanical Reset
10.0 Shortcut Operations
10.1 Add User
10.2 Delete User
11.0 Menus
12.0 Specification
13.0 Precaution
14.0 Certification
15.0 Packing List
16.0 FCC Warning

ScanLogic B22 Operation Instructions
2
1.0 System Installation
1.1 System Components
The system consists of (1) EntryPad –Part # FPC-1701A-B22 plus (1) Lock body as follows:
SwingBolt –Part # EL-0601 (not recommended as door closed notifications will not be accurate)
SwingBolt with Status–Part # EL-0601-S
DeadBolt –Part # EL-0701
SpringBolt –Part #EL-0801
1.2 Pairing the EntryPad and the Lock
SECURAM safe lock systems can operate in two different modes depending upon the type of EntryPad
being used with the lock body. The ScanLogic B22 is a digital lock system and therefore the lock must
also be programmed in digital mode. Both modes follow the same steps to reset / set which is done by
following the steps detailed below:
Step 1: Ensure the battery is connected to the Entry Pad.
Step 2: Ensure the lock cable is disconnected from the lock body.
Step 3: Locate the Reset Hole on the back of the lock (under the QC sticker).
Step 4: Using a paper clip press the reset button, inside the reset hole, 3 times to dissipate any
latent energy in the lock.
Step 5: Now press the reset button and hold.
Step 6: While continuing to press the reset button, connect the lock cable to the lock body.
Step 7: Continue to hold down the reset button for 5 seconds and then release.
Step 8: Verify that the pairing is complete by opening the lock with the default code 111111.
Step 9: Press any button on the EntryPad to initiate a lock communication test. The EntryPad
will display the following information:
Followed by:
Enter a valid code to test the lock.
The Default codes are as follows:
Super Code* (ID00) is 111111
Manager Code (ID01) is 123456
To open, enter the default code followed by pressing the Menu/Ok button.

ScanLogic B22 Operation Instructions
3
*Note: In many cases, the Super Code (ID00) is changed from default and maintained by the safe
manufacturer as a reset code for your security.
If you have difficulty resetting the lock, please call SECURAM Tech Support at [phone] or email
[e-mail].
1.3 Lock and EntryPad Installation
Included within your installation kit are (2) shoulder bolts and (3) lock mounting bolts.
Install the shoulder bolts on the safe door in the pre-drilled holes above and below the spindle
hole.
Now insert the lock cable (attached to the EntryPad) through the spindle hole.
On the backside of the safe door, you will see the lock mounting plate and the predrilled lock
mounting holes.
Connect the lock cable to the lock body and position the lock body appropriately on the lock
mounting plate.
Ensure that the lock cable is positioned so that it lies in the channel on the back of the lock. This
channel is provided to protect the lock cable from damage or crimping during installation.
Using the provided lock bolts, secure the lock body to the mounting plate.
Note: It is very important to ensure that there is an adequate gap between the lock bolt and the bolt
work. This gap must be 0.125”.
1.4 Installing the Battery –SureLock Battery Compartment (removable battery compartment)
Locate the SureLock Battery Compartment at the 5 o’clock position of the EntryPad. See Fig. 3.
Release the latch of the battery compartment, by pulling lever downward. See Fig 4.
Pull out the battery compartment from the bottom of the EntryPad. See Fig 5.
Install a new 9V alkaline battery (Duracell or Energizer brands are recommended) into the
compartment. The battery compartment will only receive the battery when the positive and
negative terminals are oriented correctly. See Fig. 6
Put the battery compartment back into the EntryPad. Push the latch of the battery
compartment up until it snaps closed. See Fig. 3

ScanLogic B22 Operation Instructions
4
1.5 Testing the Lock Operation
The ScanLogic B22 comes with two factory default codes:
•Super Code (ID00) is 111111
•Manager Code (ID01) is 123456
Enter one of the valid codes and press the Menu/OK button, to verify the communication between the
lock and EntryPad. The lock will open.
2.0 Lock Operation
Upon initial power up, the LCD screen starts a communications test as shown below:
Model Number
Software Version Number
No. of Users/ No. Users Programmed
Lock Status
After this initial power up, it will check to ensure that the system is communicating correctly. The
display will read “Link with Lock OK”.
If the Display reads: “Fail to Link with Lock” proceed to Section 1.2 entitled “Pairing the Entrypad and
the Lock”
2.1 Opening the Lock
The safe lock system has two default codes installed as follows:
•Super Code (ID00) 1-1-1-1-1-1
•Manager Code (ID01) 1-2-3-4-5-6
Step 1: Enter a valid code, then press the Menu/OK button. For example the Manager code.
The display will read “Manager or [Name] Verified” and the Lock will open.
The display will read:
The lock will relock after 6 seconds.
All codes for (ID 00 –ID 03) work in this manner.

ScanLogic B22 Operation Instructions
5
Note: with the B22 you have the opportunity to mask your code, in case someone is watching you
enter your code. On the EntryPad you can enter up to 9 digits –your 6 digit code plus up to 3
additional digits to mask your code.
For example, if your code is 1-2-3-4-5-6,
Enter 1-2-3-4-5-6 and Press Menu/OK button to open
Enter 3-4-1-2-3-4-5-6-7, where the 2 masking digits before your code (3-4) and the single
masking digit after your code (7) are concealing or masking your actual code.
If you enter less than 9 digits, you must always press the Menu/OK button to send the code to
the lock.
Note: the additional 3 masking digits can be added before and/or after your code.
3.0 Set Date and Time
3.1 Set Clock Time
Step1: Press the Menu/OK button
Step 2: At “My Menu”, press the Menu/OK button
Step 3: The display will prompt you to login. Enter a valid Super or Manager Code and press
Menu/OK; or place an enrolled finger on the fingerprint scanner.
Step 4: After logging in, the screen will show “Users”. Press Menu/OK.
Step 5: Scroll “▼” to the menu selection “Set Time” and press OK
Step 6: Each of the elements of the date and time will flash when it is available to be set. Use the
“▼”or “▲” to scroll to the correct value and press OK to move to the next element.
4.0 Code Management
The ScanLogic B22 comes with two default codes:
•Super Code (ID00) is 111111

ScanLogic B22 Operation Instructions
6
•Manager Code (ID01) is 123456
It is strongly recommended that both these default codes are changed before the lock system is put into
service.
4.1 Change Code
The B22 has 2 codes by default:
Super Code: 1 1 1 1 1 1
Manager Code: 1 2 3 4 5 6
Note: The default codes must be changed before usage; otherwise you cannot add new users or pair the
lock to the APP.
The following steps describe the Change Code process:
Step1: Press the Menu/OK button
Step 2: At “My Menu”, press the Menu/OK button
Step 3: The display will prompt you to login. Enter a valid Super or Manager Code and press
Menu/OK; or place an enrolled finger on the fingerprint scanner.
Step 4: Scroll “▼” to the menu selection “Change My Code” and Press Menu/OK
Step 6: Enter the new 6 digit code. Note: Code cannot be set to 1 1 1 1 1 1 or 1 2 3 4 5 6
Step 7: Repeat the new 6 digit code.

ScanLogic B22 Operation Instructions
7
The New Code has now been saved and is available for use.
4.2 Enroll Manager 2
The ScanLogic B22 can add a second Manager and one User, in addition to the default codes.
Note: Manager Codes have full access to the programming menu. The User Code only has access to the
change code menu option, and cannot modify any lock settings.
Step 1: Press the Menu/OK button.
Step 2: At “My Menu”, press the Menu/OK button
Step 3: The display will prompt you to login. Enter a valid Super or Manager Code and press
Menu/OK; or place an enrolled finger on the fingerprint scanner.
Step 4: After logging in, the screen will show “Users”. Press Menu/OK.
Step 5: Next the screen will show “Enroll Manager2”. Press Menu/OK
Note - Manager2 must be enrolled before you can enroll the user code (ID03)
Step 6: The screen will ask you to place your 1st finger and then to place your 2nd finger after
successfully enrolled.
If you do not want to enroll any fingerprints, press Back button to skip this step. You can also
press Back button to skip 2nd finger enrollment.

ScanLogic B22 Operation Instructions
8
Step 7: Now screen will prompt “Set Code?” If you only want fingerprint only, you can press
Back button to skip Step 8 & 9. Otherwise, press Menu/OK to continue set up a code for
Manager2.
Step 8: Now enter a 6 digit code
Step 9: Repeat new 6 digit code
Step 10: System will verify that code has been saved.
The new code is now enrolled and available to be used to open the lock.
4.3 Enroll New User
After Manager2 has been added, you can add a User (ID03).
Step1: Press the Menu/OK button.
Step 2: At “My Menu”, press the Menu/OK button
Step 3: The display will prompt you to login. Enter a valid Super or Manager Code and press
Menu/OK; or place an enrolled finger on the fingerprint scanner.
Step 4: After logging in, the screen will show “Users”. Press Menu/OK.

ScanLogic B22 Operation Instructions
9
Step 5: Next the screen will show “Enroll New User”. Press Menu/OK
Step 6: The screen will ask you to place your 1st finger and then to place your 2nd finger after
successfully enrolled. If you do not want to enroll any fingerprints, press Back button to skip
this step. You can also press Back button to skip 2nd finger enrollment.
Step 7: Now screen will prompt “Set Code?” If you only want fingerprint only, you can press
Back button to skip Step 8 & 9. Otherwise, press Menu/OK to continue set up a code for
Manager2.
Step 8: Now enter a 6 digit code
Step 9: Repeat new 6 digit code
Step 10: System will verify that code has been saved.
The new code is now enrolled and available to be used to open the lock.
4.4 Delete One User
Step1: Press the Menu/OK button
Step 2: At “My Menu”, press the Menu/OK button
Step 3: The display will prompt you to login. Enter a valid Super or Manager Code and press
Menu/OK; or place an enrolled finger on the fingerprint scanner.

ScanLogic B22 Operation Instructions
10
Step 4: After logging in, the screen will show “Users”. Press Menu/OK.
Step 4: Scroll “▼”or “▲” to the menu selection “Delete One User” and press Menu/OK
Step 5: The user information will be displayed as indicated below.
Note: To select a different user, press the "▼" or "▲" button.
Step 6: Press the "Menu/OK" button to delete the user. You will be prompted to confirm the
deletion:
Step 6: Press Menu/OK
This User code and fingerprints are now deleted from the system.
4.5 Delete All Users
This feature is used to delete all users from the system. Upon executing this command, all users will be
deleted and Manager Code will be reset to default: Manager Code (ID01) 123456
Step1: Press the Menu/OK button

ScanLogic B22 Operation Instructions
11
Step 2: At “My Menu”, press the Menu/OK button
Step 3: The display will prompt you to login. Enter a valid Super or Manager Code and press
Menu/OK; or place an enrolled finger on the fingerprint scanner.
Step 4: After logging in, the screen will show “Users”. Press Menu/OK.
Step 5: Scroll “▼”or “▲” to the menu selection “Delete All Users” and press Menu/OK
Step 6: Press the "Menu/OK"
Step 7: Press the Menu/OK button to confirm
Now all users have been deleted.
4.6 Add Finger
This feature is to add a fingerprint to the user who logged in.
Step1: Press the Menu/OK button
Step 2: At “My Menu”, press the Menu/OK button

ScanLogic B22 Operation Instructions
12
Step 3: The display will prompt you to login. Enter a valid Super or Manager Code and press
Menu/OK; or place an enrolled finger on the fingerprint scanner.
Step 4: After logging in, the screen will show “Users”.
Step 5: Scroll “▼”or “▲” to the menu selection “My Finger” and press Menu/OK
Step 6: The screen will show “Add Finger” and press Menu/OK
Step 7: The screen will show “Place 1st Finger” but if you have enrolled one fingerprint
previously, it will show “Place 2nd Finger”. Now please place your finger on the fingerprint
scanner until you see “Enrolled” on the screen.
Note: Now, you will be able to unlock and access system menu using your fingerprint.
4.7 Delete Finger
This feature will delete all fingerprints under this user.
Step1: Press the Menu/OK button
Step 2: At “My Menu”, press the Menu/OK button
Step 3: The display will prompt you to login. Enter a valid Super or Manager Code and press
Menu/OK; or place an enrolled finger on the fingerprint scanner.

ScanLogic B22 Operation Instructions
13
Step 4: After logging in, the screen will show “Users”.
Step 5: Scroll “▼”or “▲” to the menu selection “My finger” and press Menu/OK
Step 6: Scroll “▼”or “▲” to the menu selection “Delete Finger” and press Menu/OK
Step 7: The screen will show “Deleting” and then “Deleted” when completed.
Note: All enrolled fingerprints will be deleted for this user.
5.0 Smartphone Management
The ScanLogic B22 uses a smartphone to allow for remote management and control. Download the
SECURAM app on the App Store for iPhones or on the Google Play Store for Android.
5.1 Pair Phone
This feature is used to pair a smartphone to the system. This option will only appear after the default
code has been changed.
To begin, please download SECURAM Smart Home APP.
Step1: Press the Menu/OK button
Step 2: At “My Menu”, press the Menu/OK button
Step 3: The display will prompt you to login. Enter a valid Super or Manager Code and press
Menu/OK; or place an enrolled finger on the fingerprint scanner.

ScanLogic B22 Operation Instructions
14
Step 4: After logging in, the screen will show “Users”.
Step 5: Scroll “▼”or “▲” to the menu selection “Pair Phone” and press Menu/OK
Follow the steps on the APP to complete the pairing option.
5.2 Delete Phone
This feature is used to remove any mobile device connected to the system.
Step1: Press the Menu/OK button
Step 2: At “My Menu”, press the Menu/OK button
Step 3: The display will prompt you to login. Enter a valid Super or Manager Code and press
Menu/OK; or place an enrolled finger on the fingerprint scanner.
Step 4: After logging in, the screen will show “Users”.
Step 4: Scroll “▼”or “▲” to the menu selection “Delete Phone” and Press Menu/OK
Step 5: Press the "Menu/OK" to confirm

ScanLogic B22 Operation Instructions
15
Step1: Press the Menu/OK button
Note: If this operation is performed, the smartphone APP will not be able to open the lock. If the
operation such as opening the lock through the APP is required, it needs to be paired again.
6.0 System Info - System Identification
6.1 Check System Info
Step1: Press the Menu/OK button
Step 2: Press the "▼" button to the menu selection “System Info”
Step 3: Press “Menu/OK” and the screen will display information about the system.
This menu selection can be accessed within the root menu.
7.0 Lock Settings
7.1 Factory Reset (Firmware)
After the Factory Reset, the firmware version is restored to the Factory version with the user
information and parameter Settings remaining unchanged.
Please follow below steps to do Factory Reset:
Step1: Press the Menu/OK button
Step 2: At “My Menu”, press the Menu/OK button

ScanLogic B22 Operation Instructions
16
Step 3: The display will prompt you to login. Enter a valid Super or Manager Code and press
Menu/OK; or place an enrolled finger on the fingerprint scanner.
Step 4: After logging in, the screen will show “Users”.
Step 5: Scroll “▼”or “▲”to the menu selection “Lock Settings” and press Menu/OK
Step 6: The screen will now show “Factory Reset” press Menu/OK
Step 6: Press Menu/OK to confirm
Step 7: The screen will prompt the following and complete the factory reset.
7.2 Show Audit Trail
Step1: Press the Menu/OK button
Step 2: At “My Menu”, press the Menu/OK button
Step 3: The display will prompt you to login. Enter a valid Super or Manager Code and press
Menu/OK; or place an enrolled finger on the fingerprint scanner.
Step 4: After logging in, the screen will show “Users”.

ScanLogic B22 Operation Instructions
17
Step 5: Scroll “▼”or “▲”to the menu selection “Lock Settings” and press Menu/OK
Step 6: Scroll “▼”or “▲”to the menu selection “Show Audit Trail”
Step 6: Press Menu/OK and the screen will show the most recent event
Step 7: Scroll through the records by pressing "▼" or "▲”.
Note: The system records the 400 latest audit events in its internal memory.
7.3 Enable/Disable Vibration Sensor
The ScanLogic B22 has a built-in vibration sensor. The vibration sensor will send a notification to
the app in the event that the safe is being attacked. By default the Vibration sensor is enabled.
Step1: Press the Menu/OK button
Step 2: At “My Menu”, press the Menu/OK button
Step 3: The display will prompt you to login. Enter a valid Super or Manager Code and press
Menu/OK; or place an enrolled finger on the fingerprint scanner.
Step 4: After logging in, the screen will show “Users”.

ScanLogic B22 Operation Instructions
18
Step 5: Scroll “▼”or “▲”to the menu selection “Lock Settings” and press Menu/OK
Step 5: Scroll “▼”or “▲”to the menu selection “Disable Vibration”
Step 6: Press Menu/OK to select disable Vibration alert. Screen will prompt:
If the screen shows “Disable Vibration”: The Vibration Alert is enabled. When vibration is sensed,
the display will show Vibration Alert and the buzzer will sound. A notification will be sent to the
paired smartphone app.
If the screen shows “Enable Vibration”: The Vibration Alert is disabled: no alert is displayed.
Note: When alarming, use of a valid code to open the lock will cancel the vibration alarm on the
APP.
7.4 Security Level
The ScanLogic B22 has the ability to be set in two different security modes as follows:
Security Level 1 requires either a fingerprint or a code to open the lock or access menus.
Security Level 2 requires both a fingerprint and a code to open the lock or access menus.
Note: If Security Level 2 is active and the Super code holder does not have a fingerprint enrolled, the
Super Code overrides this feature.
Step1: Press the Menu/OK button
Step 2: At “My Menu”, press the Menu/OK button
Step 3: The display will prompt you to login. Enter a valid Super or Manager Code and press
Menu/OK; or place an enrolled finger on the fingerprint scanner.

ScanLogic B22 Operation Instructions
19
Step 4: After logging in, the screen will show “Users”.
Step 5: Scroll ▼”or “▲”to the menu selection “Lock Settings” and press Menu/OK
Step 6: Scroll “▼”or “▲”to the menu selection “Security Level 2”or “Security Level 1” and
press Menu/OK to change the security level.
7.5 Set Vibration Sensitivity
This menu will appear only if Vibration Alert is enabled. Please refer to 7.3 to enable Vibration Sensor.
There are five levels of vibration sensitivity with Level 1 requiring the least amount of movement to
trigger the alert and Level 5 requiring most movement to trigger the alert.
To set the sensitivity follow these steps:
Step1: Press the Menu/OK button
Step 2: At “My Menu”, press the Menu/OK button
Step 3: The display will prompt you to login. Enter a valid Super or Manager Code and press
Menu/OK; or place an enrolled finger on the fingerprint scanner.
Step 4: After logging in, the screen will show “Users”.
Step 5: Scroll ▼”or “▲”to the menu selection “Lock Settings” and press Menu/OK

ScanLogic B22 Operation Instructions
20
Step 6: Scroll “▼”or “▲”to the menu selection “Set VIB SENS”
Step 7: Scroll “▼”or “▲”to the select the level of sensitivity and press Menu/OK.
7.6 Set Battery Efficiency
There are two battery efficiency levels HI and LOW. When battery efficiency is set to HI, the system will
conserve power consumption and the battery will last longer. This however reduces the communication
range to the Smart Hub. If the communication signal to the Smart Hub is too weak, causing issues with
lock management and operation from the app, you may want to either move the Smart Hub closer to
the safe lock, or set the Battery Efficiency to LOW - power consumption will increase but the
communication will be more stable.
To set the Battery Efficiency follow these steps:
Step1: Press the Menu/OK button
Step 2: At “My Menu”, press the Menu/OK button
Step 3: The display will prompt you to login. Enter a valid Super or Manager Code and press
Menu/OK; or place an enrolled finger on the fingerprint scanner.
Step 4: After logging in, the screen will show “Users”.
Step 5: Scroll “▼”or “▲”to the menu selection “Lock Settings” and press Menu/OK