Seenergy SVR-808e User manual

8/16-Ch NVR with Dual Display
(SVR-808e/SVR-816e)
V1.0.0 15092014
Standalone NVR
Quick Installation Guide

2
Standalone NVR Quick Guide
System Overview
Front View
Rear View

Standalone NVR Quick Guide
3
LED & Buttons Definitions

4
Standalone NVR Quick Guide
HDD Installation
1.Remove the screws on back side.
Remove the top case by pulling it toward you.

Standalone NVR Quick Guide
5
2. Install HDD on brackets with screws
Prepare HDD brackets.
Fix the HDD on bracket with screws
You can install two HDDs with brackets.

6
Standalone NVR Quick Guide
3.Install SATA Cable
Prepare SATA cable.
Install SATA cables on system, install SATA data cable.
Install power cable.
Install SATA cable on the HDD.

Standalone NVR Quick Guide
7
4. Install HDD brackets
Fix HDD brackets on system with screws.

8
Standalone NVR Quick Guide
Connect to the NVR
There are various ways you can connect to the NVR and below are
the suggested methods for different network setup:
•The NVR is placed in a network with a DHCP server: Connect
to the NVR by using “Device Search” Utility
•The NVR is placed in a network without DHCP server (or you
are connecting to it directly): Access the NVR with its default IP
Use Device Search Utility
If the NVR is placed in a corporate network or a local area network
where a DHCP server is already presented, run the “Device Search”
utility from a computer that is on the same network and locate the
NVR with its IP address that is assigned by the top-level DHCP
server.

Standalone NVR Quick Guide
9
To begin, launch the “Device Search” utility from the CD and
proceed with the installation:
Once the installation is complete, check the “Launch the Search AP”
option and click “Finish”.

10
Standalone NVR Quick Guide
The search should start automatically and its status should be dis-
played.
The NVR should be located and its IP address should be displayed.
Double-click on an NVR and the search program should
automatically access the NVR’s web administration page from your
default browser.

Standalone NVR Quick Guide
11
You should be prompted for the NVR’s username and password.
Enter its default username “admin” and password “admin” and
then click ”OK” to enter the system
Access the NVR with its default IP address
The NVR comes with a pre-configured static IP “192.168.101.50”.
However, it is only used when there is no DHCP server presented in
the network. The NVR will turn on its DHCP server function and act
as the DHCP server in the network. To connect to the NVR, use a PC
that is on the same network over a switch or hub, or connect the PC
directly to the NVR using a crossover CAT5 Ethernet cable.

12
Standalone NVR Quick Guide
The PC that is connected directly to the NVR (or within the same
local area network) should receive an IP from the NVR. Simply
access the NVR from your web browser with its IP address
Again, you should be prompted for the username and password.
Enter its default username “admin” and password “admin” and
then click ”OK” to enter the system
Set up Password

Standalone NVR Quick Guide
13
The default login username and password is admin/admin. To
change the password of the admin account, go to “Setup” -->
“System Con- figurations” --> “User Account”, click on the “admin”
account in the account list then press the “edit” button to change its
password. Finally, click “Apply” to save the change.

14
Standalone NVR Quick Guide
Camera Installation
Add a Camera -- Automatic Search
Click the “Search” button to perform the camera search.
You should be prompted to install Active Control component in order
for the search to function properly. Go ahead and click “Install”
After that, the search should begin and its status should be
displayed:

Standalone NVR Quick Guide
15
Found cameras should be listed and simply select a camera from
the list and press “Configure”
Its corresponding information should be displayed in the “Camera
Information” section. Enter its username and password and select
the channel ID and name the camera.

16
Standalone NVR Quick Guide
Click on “Detect” to establish connection between the recorder and
the camera. If connection establishes successfully, camera’s
detailed information should be polled and displayed as below.
Adjust its video format, frame rate, resolution or bitrate...etc if you
wish and then click “Add” to finish adding the camera
Add a camera manually
Simply follow the instruction described above but instead of using
the “Search” function, enter the camera’s IP address and credential
in the “Camera Information “Camera Information” manually