Sega 2SPICY User manual

OWNER'S MANUAL
IMPORTANT
•  Before using this product, read this manual carefully to understand the
contents herein stated.
•  After reading this manual, be sure to keep it near the product or in a
convenient place for easy reference when necessary.
OWNER'S MANUAL2SPICY 420-7031-01
Nissay Aroma Building, 5-37-1, Kamata, Ohta-ku, Tokyo 144-8721, Japan
Phone: [phone] Facsimile: [phone]
© SEGA
420-7031-01
1ST PRINTING

TABLE OF CONTENTS
i
TABLE OF CONTENTS
E0-0703 420-7031-01
BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING:
TABLE OF CONTENTS ....................................................................................... i
INTRODUCTION ................................................................................................ iii
1HANDLING PRECAUTIONS ......................................................................... 1
2PRECAUTIONS REGARDING INSTALLATION LOCATION........................ 4
2-1 LIMITATIONS OF USAGE ................................................................................................4
2-2 OPERATION AREA ..........................................................................................................6
3PRECAUTIONS REGARDING PRODUCT OPERATION ............................. 7
3-1 BEFORE OPERATION ....................................................................................................7
3-2 DURING OPERATION (PAYING ATTENTION TO CUSTOMERS) ..................................9
4PART DESCRIPTIONS................................................................................ 10
5ACCESSORIES ........................................................................................... 11
6ASSEMBLYAND INSTALLATION .............................................................. 13
7PRECAUTIONS WHEN MOVING THE MACHINE...................................... 37
8GAME DESCRIPTION ................................................................................. 39
9EXPLANATION OF TEST AND DATA DISPLAY......................................... 52
9-1 SWITCH UNIT AND COIN METER ................................................................................54
9-2 SYSTEM TEST MODE ...................................................................................................55
9-3 GAME TEST MODE .......................................................................................................56
10 CONTROL UNIT (GUN)............................................................................... 67
11 MONITOR (LCD DISPLAY) ......................................................................... 72
11-1 SAFETY PRECAUTIONS WHEN HANDLING THE MONITOR...................................72
11-2 CLEANING THE SCREEN SURFACE .........................................................................73
11-3 ADJUSTMENT METHOD .............................................................................................74
12 COIN SELECTOR........................................................................................ 77
13 FLUORESCENT LAMP REPLACEMENT................................................... 79
14 PERIODIC INSPECTION ............................................................................. 82
15 TROUBLESHOOTING................................................................................. 84
15-1 TROUBLESHOOTING TABLE.....................................................................................84
15-2 FUSE REPLACEMENT ................................................................................................86
15-3 ERROR DISPLAY ........................................................................................................87

ii
TABLE OF CONTENTS
16 GAME BOARD ............................................................................................ 91
16-1 REMOVING THE LINDBERGH RED ...........................................................................92
16-2 COMPOSITION OF THE GAME BOARD ....................................................................94
17 DESIGN-RELATED PARTS......................................................................... 95
18 PARTS LIST................................................................................................. 96
19 WIRE COLOR CODE TABLE.................................................................... 142
20 WIRING DIAGRAM.................................................................................... 143

TABLE OF CONTENTS
iii
INTRODUCTION
This manual is intended to provide detailed descriptions together with all the necessary information covering the
general operation of electronic assemblies, electro-mechanicals, servicing control, spare parts, etc. for the product,
"2SPICY."
This manual is intended for the owners, personnel and managers in charge of operation of the product.
Operate the product after carefully reading and sufciently understanding the instructions.
In the unlikely event that the product does not function correctly, DO NOT allow anyone other than a technician
to touch the internal system. Turn off the power to the machine, making sure to unplug the electrical cord from the
outlet, and contact the ofce listed below or the point of purchase for this product.
Use of this product is unlikely to cause physical injuries or damage to property. However, points that require special
attention are indicated by bold text, the word "IMPORTANT" and the symbol below.
Indicates important information that, if ignored, may result in the mishandling of
the product and cause faulty operation or damage to the product.
Sega Amusements U.S.A., Inc.
800 Arthur Avenue, Elk Grove Village, IL 60007-5215, U.S.A.
TEL: [phone]
TOLL FREE: 1-888-877-2669
FAX: [phone]
SEGA AMUSEMENTS EUROPE, LTD.
Suite 3a, Oaks House 12-22, West Street, Epsom, Surrey, KT18 7RG, United Kingdom
Telephone: [phone] Facsimile: [phone]
e-mail: [email protected] http://www.sega-amusements.co.uk
SPECIFICATIONS
Installation space:
Width: 865.5 mm (34.1 in.)
Depth: 1,664 mm (65.5 in.) <Recommended>
1,290 mm (50.8 in.) <Minimum>
Height: 2,176 mm (85.7 in.)
Weight: Front Cabinet: 128 kg (282.2 lbs) (Including billboard)
Rear Cabinet: 63 kg (138.9 lbs) (Including pedal unit)
Power, maximum current: 470 W, 2.7 A (AC 220 V, 50 Hz Area)
440 W, 2.6 A (AC 220 V, 60 Hz Area)
470 W, 2.6 A (AC 240 V, 50 Hz Area)
Power, current: 445 W, 5.18 A, (Max.) (AC 110 V, 60 Hz; Taiwan)
343 W, 4.05 A, (Min.) (AC 110 V, 60 Hz; Taiwan)
Monitor: 32 Type LCD Monitor
NOTE: The contents herein described are subject to change without notice.

iv
INTRODUCTION
Denition of ‘Site Maintenance Personnel or Other Qualied Individuals’
Parts replacement, maintenance inspections and troubleshooting should be carried out by site maintenance personnel
or other qualied professionals. This manual includes directions for potentially dangerous procedures which should
only be carried out by professionals with the appropriate specialized knowledge.
The site maintenance personnel or other qualied professionals mentioned in this manual are dened as follows:
Site maintenance personnel:
Individuals with experience in maintaining amusement equipment, vending machines, etc., working under the
supervision of the owner/operator of this product to maintain machines within amusement facilities or similar
premises by carrying out everyday procedures such as assembly, maintenance inspections, and replacement of units/
expendable parts.
Activities to be carried out by site maintenance personnel:
Amusement equipment/vending machine assembly, maintenance inspection and replacement of units/expendable
parts.
Other qualied professionals:
Persons employed by amusement equipment manufacturers, or involved in design, production, testing or
maintenance of amusement equipment. The individual should have either graduated from technical school or hold
similar qualications in electrical/electronics/mechanical engineering.
Activities to be carried out by other qualied professionals:
Amusement equipment/vending machine assembly, repair/adjustment of electrical/electronic/mechanical parts.
Procedures not described in this manual or marked as 'to be carried out by site
maintenance personnel or other qualified professionals' should not be carried
out by personnel without the necessary skill or technology. Work carried out by
unqualied persons may cause serious accidents, including electrocution.

HANDLING PRECAUTIONS
1
1
HANDLING PRECAUTIONS
When installing or inspecting the machine, be very careful of the following points and pay attention to ensure that
the player can enjoy the game safely.
Non-compliance with the following points or inappropriate handling running counter to the cautionary matters
herein stated can cause personal injury or damage to the machine.
• Before performing work, be sure to turn the power off. Performing the work
without turning the power off can cause an electric shock or short circuit. In the
case work should be performed in the status of power on, this manual always
states to that effect.
• To avoid an electric shock or short circuit, do not plug in or unplug quickly.
• To avoid an electric shock, do not plug in or unplug with a wet hand.
• Donotexposepowercordsorearthwiresonthesurface,(oor,passage,
etc.). If exposed, the power cords and earth wires are susceptible to damage.
Damaged cords and wires can cause an electric shock or short circuit.
• Toavoidcausingareoranelectricshock,donotputthingsonordamagethe
power cords.
• When or after installing the product, do not unnecessarily pull the power cord. If
damaged,thepowercordcancauseareoranelectricshock.
• In case the power cord is damaged, ask for a replacement through where the
productwaspurchasedfromortheofcehereinstated.Usingthecordasis
damagedcancausere,anelectricshockorleakage.
• Be sure to perform grounding appropriately. Inappropriate grounding can
cause an electric shock.
• Besuretousefusesmeetingthespeciedrating.Usingfusesexceedingthe
speciedratingcancauseareoranelectricshock.
• BesurethatconnectionssuchasICBDaremadeproperly.Insufcientinsertion
can cause an electric shock.
• Specicationchanges,removalofequipment,conversionand/oraddition,not
designated by SEGA are not permitted.
-Failuretoobservethismaycauseareoranelectricshock.Non-compliance
withthisinstructioncanhaveabadinuenceuponphysicalconditionsofthe
players or the onlookers, or result in injury during play.
- SEGA shall not be held responsible for damage, compensation for damage to
athirdparty,causedbyspecicationchangesnotdesignatedbySEGA.
• If work or parts replacement not indicated in this manual is carried out, an
accident may occur. If it is necessary to carry out work not indicated in this
manual,besuretohaveitdonebytheofceindicatedinthismanualorbythe
point of purchase. Also, please inquire regarding details of the work involved.
• Be sure to perform periodic maintenance inspections herein stated.
1

2
HANDLING PRECAUTIONS
1
• For the IC board circuit inspections, only the logic tester is allowed. The use of a
multiple-purpose tester is not permitted, so be careful in this regard.
• Static electricity from your body may damage some electronics devices on the
IC board. Before handling the IC board, touch a grounded metallic surface so
that the static electricity can be discharged.
• Do not turn the power on and off continuously. Repeatedly turning the power on
and off may cause product malfunction or parts damage.
• Somepartsarenotdesignedandmanufacturedspecicallyforthisgame
machine.Themanufacturersmaydiscontinue,orchangethespecicationsof
such general-purpose parts. If this is the case, SEGA cannot repair or replace a
failed game machine whether or not a warranty period has expired.

HANDLING PRECAUTIONS
3
1
CONCERNINGTHESTICKERDISPLAY
This SEGA product has stickers attached describing
the product manufacture No. (Serial No.) and Electrical
Specications. It also has a Sticker describing where to
contact for repair and for purchasing parts.
When inquiring about or asking for repairs, mention
the Serial No. and Name of Machine indicated on
the Sticker. The Serial Number indicates the product
register. Identical machines could have different
parts depending on the date of production. Also,
improvements and modications might have been made
after the publication of this manual. In order to ensure
you order the correct parts, mention the Serial No. when
contacting the applicable places.
CONCERNINGWARNINGDISPLAYS
This SEGA product has warning displays on stickers,
labels and/or printed instructions adhered/attached to or
incorporated in the places where a potentially hazardous
situation could arise. The warning displays are intended
for accident prevention for customers and for avoiding
hazardous situations relating to maintenance and
servicing work. Some portions of the cabinet contain
high voltage and may cause accidents if touched. When
performing maintenance, be very careful of the warning
displays. It is especially important that any complex
repair and replacement work not mentioned herein
should be performed by those technical personnel who
have knowledge of electricity and technical expertise.
In order to prevent accidents, caution any customer
ignoring the warnings to cease and desist immediately.
440-CS0323-EG
440-WS0164-EG
Serial No. Display
Electrical Specifications Display
Serial No. Display
440-WS0300-EG
440-WS0300-EG
440-CS0186-EG
440-WS0165-EG
440-WS0165-EG
440-WS0002XEG
440-WS0281-EG

4
PRECAUTIONS REGARDING INSTALLATION LOCATION
2
PRECAUTIONS REGARDING INSTALLATION LOCATION
This product is an indoor game machine. Do not install it outside. Even indoors,
avoidinstallinginplacesmentionedbelowsoasnottocauseare,electric
shock,injuryand/ormalfunction.
- Places subject to rain or water leakage, or places subject to high humidity in the
proximityofanindoorswimmingpooland/orshower,etc.
- Places subject to direct sunlight, or places subject to high temperatures in the
proximity of heating units, etc.
-Placeslledwithinammablegasorvicinityofhighlyinammable/volatile
chemicals or hazardous matter.
- Dusty places.
- Sloped surfaces.
- Places subject to any type of violent impact.
-Vicinityofanti-disasterfacilitiessuchasreexitsandreextinguishers.
- Areas where the temperature exceeds the applicable temperature (ambient
temperature) range of 5 to 30 degrees centigrade.
• BesuretochecktheElectricalSpecications.Ensurethatthisproduct
is compatible with the location's power supply, voltage, and frequency
requirements.AplatedescribingElectricalSpecicationsisattachedtothe
product.Non-compliancewiththeElectricalSpecicationscancauseare
and electric shock.
• This product requires a breaker and earth mechanism as part of the location
facilities.Usingtheproductwithoutthesecancauseareandelectricshock.
• Ensure that the indoor wiring for the power supply is rated at 15 A or higher (AC
single phase 100 V ~ 120 V area), and 7 A or higher (AC 220 V ~ 240 V area).
Non-compliancewiththeElectricalSpecicationscancauseareandelectric
shock.
• Be sure to use an independent power supply equipped with an earth leakage
breaker.Usingapowersupplywithoutanearthleakagebreakercancausean
outbreakofreifapowersurgeoccurs.
• Putting many loads on one electrical outlet can cause generation of heat and a
reresultingfromoverload.
• When using an extension cord, ensure that the cord is rated at 15 A or higher (AC
100V~120Varea)and7Aorhigher(AC220V~240Varea).Usingacord
ratedlowerthanthespeciedratingcancauseareandelectricshock.
2
2-1 LIMITATIONS OF USAGE

PRECAUTIONS REGARDING INSTALLATION LOCATION
5
2
PRECAUTIONS REGARDING INSTALLATION LOCATION
Electricity Consumption:
MAX. 2.7 A (AC 220 V, 50 Hz)
MAX. 2.6 A (AC 220 V, 60 Hz)
MAX. 2.6 A (AC 240 V, 50 Hz)
MAX. 5.18 A (AC 110 V, 60 Hz) <TAIWAN>

6
PRECAUTIONS REGARDING INSTALLATION LOCATION
2
• For the operation of this machine, secure a minimum area of 1.5 m (4.9 ft) [W]
x 2.4 m (7.9 ft) [D]. The dimensions of the base periphery are established in
consideration of ventilation, maintenance and customer passage. And if they
fall and hit their head, there could be a very serious injury. Be sure to always
secure enough space as prescribed in this manual.
• Besuretoprovidesufcientspacespeciedinthismanual.Donotallowobjects
toblocktheventilationports.Itcancausegenerationofheatandare.
• SEGA shall not be held responsible for damage or compensation for damage to
a third party, resulting from the failure to observe this instruction.
2-2 OPERATION AREA
In order to transport the machine into a building, the minimum necessary
dimensionsoftheopening(ofdoors,etc.)are0.8m(2.7ft)[W]and1.8m(5.9ft)[H].
350 350 350 300 350
1500 2600
600
2402.4
2402.4
600 400 150
400 150
FIG. 2-2b
(Ref.) Recommended installation dimensions for two
units used for competitive play
FIG. 2-2a
Recommended installation
dimensions

PRECAUTIONS REGARDING PRODUCT OPERATION
7
3
In order to avoid accidents, check the following before starting the operation:
• To ensure maximum safety for the players and the customers, ensure that where
theproductisoperatedhassufcientlightingtoallowanywarningstoberead.
Operationunderinsufcientlightingcancausebodilycontactwitheachother,
hittingaccident,and/ortroublebetweencustomers.
• Be sure to perform appropriate adjustment of the monitor (projector). For
operationofthismachine,donotleavemonitor'sickeringordeviationas
is.Failuretoobservethiscanhaveabadinuenceupontheplayers'orthe
customers' physical conditions.
• It is suggested to ensure a space allowing the players who feel sick while
playing the game to take a rest.
• Check if all of the adjusters are in
contact with the surface. If they
are not, the cabinet can move
and cause an accident.
• Do not put any heavy item on this product. Placing any heavy item on the
product can cause a falling down accident or parts damage.
• Do not climb on the product. Climbing on the product can cause falling down
accidents. To check the top portion of the product, use a step ladder.
• To avoid electric shock, check to see if door & cover parts are damaged or
omitted.
• Toavoidelectricshock,shortcircuitand/orpartsdamage,donotputthe
following items on or in the periphery of the product.
Flowervases,owerpots,cups,watertanks,cosmetics,andreceptacles/
containers/vesselscontainingchemicalsandwater.
3-1 BEFORE OPERATION
Ensure that all the adjusters are
in contact with the floor.
PRECAUTIONS REGARDING PRODUCT OPERATION
3
To avoid injury and trouble, be sure to pay attention to the behavior of visitors and players.

8
PRECAUTIONS REGARDING PRODUCT OPERATION
3
• Toavoidinjury,besuretoprovidesufcientspacebyconsideringthepotentially
crowdedsituationattheinstallationlocation.Insufcientinstallationspacecan
causecontact,collisions,and/ortroublebetweencustomers.
• Every day when cleaning the gun, inspect the gun and make sure that there
are no scratches or cracks in the surface, and that the fastening screws are not
loose. If the game is played with scratches, cracks or loose screws, it can cause
injuries to the player or to people nearby.
Ensure that all connecting wires are
not damaged.
Ensure that the screws are not loose and are all present.
Ensure that the casing is free of
scratches and cracks.
Ensure that the trigger is
functioning properly.
• Players directly hold the controller with their bare hands so it is recommended
that wet towels (paper towels) be provided.
• PlacingtheLCDmonitornearhalogenlampsorothertypesoflightxtures
which emit strong light may cause a malfunction. Make sure to install the
monitor at a reasonable distance from such sources of light.

PRECAUTIONS REGARDING PRODUCT OPERATION
9
3
To avoid injury and trouble, be sure to pay attention to the behavior of visitors and players.
• For safety reasons, do not allow any of the following people to play the game.
- Those who need assistance such as the use of apparatus when walking.
- Those who have high blood pressure or a heart problem.
- Those who have experienced muscle convulsion or loss of consciousness
when playing video games, etc.
- Those who have neck or spinal cord problems.
-Thosewhoareintoxicatedorundertheinuenceofdrugs.
- Pregnant women.
- Those who are not in good health.
- Those who do not follow the attendant’s instructions.
-ThosewhocannotgrasptheControlUnitsecurelybecauseofimmobilityin
ngers,handsorarms.
- Persons who disregard the product's warning displays.
• Even players who have never been adversely affected by light stimulus might
experience dizziness or headache depending on their physical condition when
playing the game. Small children are especially likely to experience these
symptoms. Caution guardians of small children to keep watch on their children
during play.
• Instruct those who feel sick during play to have a medical examination.
• To avoid injury from falls and electric shocks due to spilled drinks, instruct the
player not to place heavy items or drinks on the product.
• To avoid electric shocks and short circuits, do not allow customers to put
handsandngersorextraneousmatterintheopeningsoftheproductorsmall
openings in or around the doors.
• To avoid falls and resulting injury, immediately stop the customer from leaning
against or climbing on the product, etc.
• To avoid electric shock and short circuit, do not allow customers to unplug the
powerplugwithoutajustiablereason.
• Immediately stop such violent acts as hitting and kicking the product. Such
violent acts can cause parts damage or cause the cabinet to fall over, resulting
in injury.
• Instruct players to hold the gun securely while playing. If the gun is dropped, it
could cause injury to the player.
• Itemssuchaslargengerringscancauseinjurytothengerswhileplaying.
Instruct players to remove all accessories that could cause an accident before
playing.
• Instruct players that a single gun is never to be held by two or more people
during play. Otherwise there could be dangerous contact or a collision.
3-2 DURING OPERATION (PAYING ATTENTION TO CUSTOMERS)

10
PART DESCRIPTIONS
4
PART DESCRIPTIONS
TUBE
REAR LID
AC UNIT
PEDAL
REAR CABINET
FRONT CABINET
BILLBOARD
CONTROL UNIT (GUN)
4
FIG. 4 Overall View
TABLE 4 Dimensions and Weights for Major Parts
ITEMS Width x Depth x Height Weight
BILLBOARD 865.5 mm (34.1 in) x 465 mm (18.3 in) x 455 mm (17.9 in) 12 kg (26.5 lb)
FRONT CABINET 820 mm (32.3 in) x 616 mm (24.3 in) x 1,732 mm (68.2 in) 116 kg (255.7 lb)
REAR CABINET 800 mm (31.5 in) x 370 mm (14.6 in) x 967 mm (38.1 in) 52 kg (114.6 lb)
PEDAL 622.5 mm (24.5 in) x 385.2 mm (15.2 in) x 86 mm (3.4 in) 11 kg (24.3 lb)
UPON COMPLETION
(recommended) 865.5 mm (34.1 in) x 1664 mm (65.5 in) x 2176 mm (85.7 in) 191 kg (421.1 lb)

ACCESSORIES
11
5
ACCESSORIES
Conrm that the accessories listed in the table below are present when setting up the product.
Accessories marked “Spare” in the note column are consumable items but included as spares.
KEY MASTER
220-5793-2-A001 (2)
For opening/closing
the doors
LINDBERGH RED SERVICE MANUAL
420-7032-01 (1)
Explanation of built-in game board
DESCRIPTION: OWNER’S MANUAL
Part No. (Qty.): 420-7031-01 (1)
Note: This manual
Figures:
Parts not labeled with part numbers are as yet unregistered
or cannot be registered. Be sure to handle all parts with
care, as some parts are not available for purchase separately.
PLATE LEG
APA-0003 (4)
For Front Design Plate
installation, see chapter 6 [9].
STICKER 1P2P
APA-0004 (1)
For installation,
see chapter 6 [5].
NETWORK (LAN) CABLE
600-7269-0500 (1)
For network play, see chapter 6 [5].
MICROSWITCH
509-5080 (1)
Spare, see chapter 10.
FRONT DESIGN PLATE 1P, 2P
APA-0001 (1)
APA-0002 (1)
For installation, see chapter 6 [9].
KEY
(2)
For the rear cabinet’s
cashbox door
Located inside the service
door of the rear cabinet at
time of shipment
KEY
(2)
For the front cabinet’s
cashbox door
Located inside the service
door of the front cabinet
at time of shipment
FASTENER, WASHER
FAS-290045 (4)
280-6686-01 (4)
For Front Design Plate
installation, see chapter 6 [9].
5
TABLE 5a ACCESSORIES
FUSE 250 V, 200 mA
514-5143-200 (1)
Spare, see 15-3.
FUSE 250 V, 2 A
514-5143-2000 (1)
Spare, see 15-3.
HEAT SHRINKABLE TUBING
(SUMITUBE F D 20MM)
310-5029-D20 (2)
Spare, see chapter 10.

12
ACCESSORIES
5
The parts listed in Table 5b are packaged separately, but they must always be attached when using the product. They
are attached while assembling and installing the product.
DVD WIRE FOR LINDBERGH RED (2 m)
605-0094-01 (1)
For software installation, see chapter 6 [8].
POWER CABLE
600-6729-01 (1) <Taiwan>
600-6619-02 (1) <Singapore, Malaysia>
600-6618-01 (1) <Others>
For installation, see 6-4.
DVD KIT (1)
To order the DVD-ROM by itself, use the following
part number: 610-0726-0027: DVD SOFT APA.
STICKER 845-0002D-02
443-50002D-02 (1)
Board number sticker, see chapter 6 [6].
DVD-ROM (1)
CUSHION SPONGE
601-11137 (1)
protective material
DISC CASE
KEY CHIP (1)
NOTE: Use the (2 m) wire included with this product, and
not the (1 m) wire included with the DVD DRIVE kit.
TABLE 5b
TABLE 5c XKT-1515-01: DVD DRIVE KIT FOR LBG ENG
DVD WIRE
605-0094 (1)
For software installation.
NOTE: Do not use with this product.
SERVICE MANUAL
420-6923-01 (1)
DVD DRIVE
610-0719-01-91 (1)
For software installation,
see chapter 6 [8].
845-0002D-02

ASSEMBLY AND INSTALLATION
13
6
• Thisworkshouldbecarriedoutbysitemaintenancepersonnelorotherqualied
professionals. Work performed by non-technical personnel can cause a severe
accident such as electric shock. Failing to comply with this instruction can
cause a severe accident such as electric shock to the player during operation.
• Perform assembly work by following the procedure herein stated. Failure to
comply with the instructions can cause electric shock.
• Perform assembling as per this manual. Since this is a complex machine,
incorrectassemblingcancauseanelectricshock,machinedamageand/or
improperfunctioningasperspeciedperformance.
• When assembling, more than one person is required. Depending on the
assembly work, there are some cases in which working by one person alone
can cause personal injury or parts damage.
• Ensure that connectors are properly connected. Improper connections can
cause electric shock.
• Be careful not to damage the wires. Damaged wires may cause electric shock
orshortcircuitorpresentariskofre.
• Do not carelessly push on the monitor. This could cause it to fall over.
• Providesufcientspacesothatassemblingcanbeperformed.Performing
work in places with narrow space or low ceiling may cause an accident and
assemblyworktobedifcult.
• To perform work safely and avoid serious accident such as the cabinet falling
down, do not perform work in places where step-like grade differences, a ditch,
or slope exist.
• Do not use connectors other than those connected to and used by the game
board at the time of shipment. Do not connect wires to unused connectors. This
could cause the generation of heat or smoke, or a burnout.
ASSEMBLY AND INSTALLATION
6
• Wearappropriateworkclothingsothatworkcanbeperformedsafely.Use
gloves and safety shoes to prevent accidents or injuries.
• Wheninstallingawireprotectioncoveroveraoor,useamaterialshaped
sothatnoonepassingbywillstumbleoverit.Usingamaterialthatcouldbe
stumbled over might lead to an accidental fall.
• Be careful in handling plastic parts. Be sure not to tighten screws or nuts
too tightly. If such parts are exposed to excessive loads or impact, they
might become damaged, resulting in fragments or cracks that could cause
accidental injury.

14
ASSEMBLY AND INSTALLATION
6
Use the following tools for assembly work.
- Philips screwdrivers (for M4,M6,M8)
- Sockets for hexagon bolts and nuts (for M8)
- Socket wrench
- 24 mm spanner
- MASTER KEYS (Accessory)
- ALLEN WRENCH (2.5 mm)
24mm
Installation and assembly of this product should take place in the following sequence.
1 Installation of Billboard
2 Connection of Front Cabinet, Rear Cabinet, and Tube
3 Fixation to Installation Site
4 Installation of Pedal
5 Preparation of Two Units for Competitive Play (1P: left side, 2P: right side)
6 Preparation for Software Installation
7 Connection of Power and Ground
8 Engagement of Power Supply and Software Installation
9 Installation of Front Design Plate
10 Engagement of Power Supply after Installing Software
11 Assembling Check

ASSEMBLY AND INSTALLATION
15
6
1
Attach the billboard plate to the billboard
box with four screws.
2
Two people lift up the billboard, and place it on the top of the front cabinet.
3
Slide the billboard forward, pushing it into
the gap.
FIG. 6-1b
FRONT CABINET
BILLBOARD
FIG. 6-1c
➡
FIG. 6-1d
HEXAGONSOCKETSCREW(4)
M4x6,specialwasherused
FIG. 6-1a
1 INSTALLATION OF BILLBOARD