Seizmik 08072 User manual

1
Installation & Operations Manual
Kubota RTV X 900 1120D - 2 Piece Hood Rack
Part Number
#08072
Seizmik makes Windshields, Doors, Tops, Hood Racks, Brush Guards, and other great accessories for utility
vehicles & side x sides. Our products are engineered tough for long life and tested under the harshest of conditions.
Always observe the warnings and precautions in this manual when using your Seizmik products. For best results,
carefully follow the instructions in this manual and make no modifications.
Seizmik products are designed, developed and manufactured by Vialink Corp. If you have any questions,
comments, need assistance, or are missing parts, please call 1-866-838-3366 between 9:00AM and 5:00PM EST.
You can email us at [email protected]
Installation information:
• This product has an installation rating of: Easy
• Approximate installation time: 30 Minutes
• This product is easiest to install with: 2 people

2
A
B
D
C
G
H
E F
I
J
Parts List
Parts:
A. 2 Piece Basket
B. Front riser/Light Mounting
Plate
C. Bumper Mount
D. Front clamp (2)
E. Rear clamp (2)
F. Hood Rack Bracket (L,R)
G. Extendable Tubes (2)
H. Front riser stem(2)
I. Front riser caps (2)
J. Kubota Bumper
extenders (2)
Hardware:
(16) M6 16mm Socket Head Bolts
(1) M6 30mm Socket Head Bolt
(1) M6 35mm Socket Head Bolt
(16) M6 Flat washers
(18) M6 Lock Nuts
(2) M8 x 25 Hex Head Bolts
(2) M8 Lock Nuts
Basket Assembly
M6x35mm
M6x30mm
x1
x1
1. Assemble two sides of rack. Secure the back of the
rack with a single M6 35mm Socket Head bolt and lock
nut. Secure the front of the rack with a single M6 30mm
Socket Head bolt and lock nut.
2. Insert the two (G) Extendable Tubes in the ends of
the hood rack. Tighten bolts at the ends with a 6mm
Hex key just enough to hold tube in place. Fully tighten
all bolts before use.

4. Attach the Kubota bumper extenders (J) to the bumper mount using (2) M8 x 25 Hex Head Bolts. Set the assembly
onto the Kubota bumper and attach using the factory bolts on the Kubota.
3
1 2
Important Notes
To open a clamp, lift up on both levers in the order
above. Orient all clamps so the first clamp lever
opens towards the front of the vehicle. To increase
clamping force, spin the lever clockwise; to decrease
the clamping force, spin the lever counter-clockwise
before locking.
Spin lever to
adjust clamping
force
Clamp Orientation and adjustment
Front of Vehicle
Bumper Mount and Front Clamp Assembly
3. Attach the two front clamps (D) to the bumper mount (C)
using (4) M6 x 16mm bolts, (2) washers and (4) locknuts.
Make sure all clamp levers open away from the vehicle.
6. Attach the Rear Clamp (E) to the Hood Rack
brackets using (2) M6 x 16mm bolts, (2) washers, and
(2) locknuts as shown above. The clamps should open
towards the front of the vehicle.
M6x16mm
x4
Rear Bracket and Clamp Assembly
5. Install the Hood Rack Brackets (F) to the front roll
cage with four M6 x 16mm socket head bolts (4)
washers and (4) locknuts for each side. Point the
bracket towards the front of the vehicle. Do not fully
tighten bolts yet as you may need to adjust when you
put the basket in place.
M6x16mm
x4
M6x16mm
x4
M8x25mm x2

4
Riser Assembly
Locking Bolt
7. Note the riser orientation shown above. Insert the 2 Front riser stems into the front riser/light mounting plate a
few inches in. Tighten the locking bolt at the top of the tube with hex key just enough to hold the riser stems in
place. You will tighten after final assembly.
Basket Installation and Adjustment
8. Attach the riser assembly to the front of the hood rack and bolt the two front riser caps in place. Snug the cap
bolts, but keep them loose enough to allow rotation. Make sure all 4 clamps are open, then set the rack in place.
9. Adjust the width of the extendable tubes so they stick out just past the clamps. The hood rack angle can be
adjusted by loosening the bolt on the front riser stems and lifting up or pushing down on the front of the rack.
Adjust clamps and brackets as necessary, then tighten all bolts. We recommend no more than 5% of slope to
the hood rack.
Locking Bolt

5
How to get Help - If you have any questions, comments, need assistance, or are missing parts, please call
1-866-838-3366 between 9:00AM and 5:00PM EST. You can email us at [e-mail], visit
www.seizmik.com to download installation guides and product info, or contact your powersports dealer where you
purchased your Seizmik product if you need additional assistance.
Congratulations –You have now finished the installation of your Seizmik Hood Rack.
Lights or a light bar can be attached to the hood rack by drilling holes in the light mounting plate. We
recommend our 13” 60 Watt Siezmik Light Bar with 5,400 Lumen output. Part Number #12037
Attaching Other Accessories to your hood rack.