Steelcase Duo Tall Storage Mounted on Montage User manual

Page 1 of 8
939500188 Rev C
Duo™Tall Storage Mounted on Montage®
If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
©2006 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
3/32" DIAMETER
DRILL BIT

1c
Page 2 of 8
939500188 Rev C
1. With a pencil, mark the measurements as
indicated (1a). Align the mounting bracket as
shown and mark the hole locations (1b). Using
a 3/32" drill bit, drill two (2) holes 1/4" deep (1c).
Attach the mounting bracket to the side of the
tall storage unit using two (2) #8-18 x 3/4"
screws (1d).
1a 1b
5"
9"
18"
C
L
C
L
MOUNTING
BRACKET
1d
USING A 3/32" DRILL BIT,
DRILL TWO (2) HOLES 1/4" DEEP
#8-18 X 3/4" SCREWS

Page 3 of 8
939500188 Rev C
2. Align column base to column. 3. Attach using four (4) 1/4-20 x 1" flat head screws (2b).
2
COLUMN
BASE
COLUMN
1/4-20 x 1" FLAT
HEAD SCREWS
3

Page 4 of 8
939500188 Rev C
4. Flip the tall storage unit
over and mark with a pencil the
measurements as shown.
5. Align the column perpendicular
to the wall. Adjust distance from
wall according to the tall storage
length being used.
Underside of Tall Storage Unit
(Column End)
5
9"
18"
6"
4
C
L

Page 5 of 8
939500188 Rev C
6. Lower the tall storage unit into place (6a) by
sliding the mounting bracket into the slots on the
wall (6b) and placing the other end of unit upon
the column (6c).
7. Make sure the tall storage is centered
with the column according to the
measurements drawn in
step 4 on page 4.
6c
A
6a
6b
7
PENCIL
MARKS
CENTERED
NOTE: If installing a cantilevered
worksurface under the tall storage
unit, install the cantilever and the
mounting plate before step 6.

9a
9b
Page 6 of 8
939500188 Rev C
8. Attach tall storage unit to the duo column
by drilling six (6) 3/32" dia. holes, 1/4" deep
(8a). Attach using six (6) #8-18 x 5/8" flat
head screws (8b).
9. Adjust the height of the tall storage
unit by twisting the column (9a)
until level (9b).
Underside of Tall Storage Unit
(Column End)
8a
DRILL SIX (6) HOLES
USING A 3/32" DIA. DRILL BIT,
1/4" DEEP
8b
#8-18 x 5/8"
FLAT HEAD SCREWS

10d
Page 7 of 8
939500188 Rev C
10. Place the mounting bracket
against the panel and underneath the
tall storage unit (10a). With a pencil,
mark the two (2) hole locations of the
bracket onto the underside of the tall
storage unit (10b). Remove the bracket
and drill two (2) 3/32" dia. holes, 1/4"
deep (10c). Replace the bracket and
attach using two (2) #10-16 x 1" pan
head screws (10d).
MOUNTING
BRACKET
#10-16 x 1"
PAN HEAD SCREWS
UNDERSIDE OF
TALL STORAGE UNIT
10a
10b
10c
DRILL TWO (2)
3/32" DIA. HOLES,
1/4" DEEP

Page 8 of 8
939500188 Rev C
11. Install worksurface.
12. With the worksurface installed
and resting upon the mounting
bracket (12a) drill two (2) 3/32" dia.
holes, 1/4" deep (12b). Attach
worksurface to the mounting bracket
using two (2) #10-16 x 1" pan head
screws (12c).
MOUNTING
BRACKET
UNDERSIDE OF
WORKSURFACE
UNDERSIDE OF
TALL STORAGE UNIT
PANEL
12a
12b
12c
#10-16 x 1"
PAN HEAD SCREWS
DRILL TWO (2) HOLES
USING A 3/32" DIA.
DRILL BIT,
1/4" DEEP