Benthin P1753 Parts list manual

Operation Installation – Operation – Care
Thanks to a special manufacturing process, our fabric qualities are
furnished with an antistatic finish and are therefore resistant to
dust and dirt. Occasional brushing with a soft brush or a feather
duster is usually sufficient.
When cleaning glass and the window frame, make sure that no
water or caustic cleaning agents come into contact with the pleated
blind fabric.
No guarantee can be offered for damage to fabrics that is
attributable to condensation, cleaning agents or soiling by insects.
Care
Operation
Operation Model P1751
To open and close the blind, pull the cord by the tassel inwards
(lock released) and pull the blind upwards or lower it.
To stop the blind pull the cord vertically (cord is locked).
Model
P1753, P1751, P1741, P1740
© 2014 Benthin® .Misprints, errors and changes excepted .Version 03-03-2014 .97000168
Operation Model P1741
To open the blind: Pull the cord on the tassel straight
downwards. To close the blind: Pull the tassel to the middle of the
blind and lead the cord upwards.
Operation Model P1740/P1753
Blind
open/close
Blind
fix
To open the blind:
1. Bottom: Pull the cord on the tassel straight downwards.
2. Top: Pull the cord by the tassel inwards (lock released) and
pull the blind upwards.
To stop the blind pull the cord vertically (cord is locked).
To close the blind:
1. Top: Pull the cord by the tassel inwards (lock released) and
lower the blind.
To stop the blind pull the cord vertically (cord is locked).
2. Bottom: Pull the cord by the tassel towards the centre of the blind
and lower the blind.
To stop the blind pull the cord vertically (cord is locked).
Dear Customer,
this dimensionally accurate blind was produced especially according to your
requirements. High quality materials and a design that is perfect in function
and elegance guarantee a long service lifetime and thus ensure great
pleasure in the purchased product.
Your blind Manufacturer
Please read this instructions carefully
before fitting the blind.
Blinds must be fitted by skilled personnel.
Wrong installation may result in accidents.
Alterations of the blind must be approved by the blind manufacturer.
No screws for fixing are enclosed. Always use appropriate screws and plugs
suited for the wall or ceiling material where the blind is fitted!
WARNING
• Young children can strangle in the loop of pull cords,
tapes and cords that operate window coverings.
They can also wrap cords around their necks.
• To avoid strangulation and entanglement,
keep cords out of reach of young children.
• Move beds, cots and furniture away from
window covering cords.
• Do not tie cords together.
Make sure cords do not twist and create a loop.
• Install and use the included safety devices according to the installation
instructions on these device to reduce possibility of such an accident.
According to EN 13120
1. 2.
1.
2.
P1741
P1740
P1753
P1751

Mounting Mounting Child Safety
Recommendation: DIN 7982 Ø 3,9 x 13 mm
(for wooden and synthetic frames)
Wall installation with mounting bracket and clip
Installing the window moulding with moulding locking strip and clip
Mounting window frames with holding clamps
Recommendation: DIN 7981 Ø 2,9 x 9,5 mm
(for wooden and synthetic frames)
Dismantle mounting bracket
!1.
2.
Attention: Model P1741
Mount the sloping
bottom profile (1) and then the
horizontal top profile (2).
2
2
1
1
Clip
Place the profile in the back edge of the clip and push the front of
the profile upwards (till it clicks in).
When dismounting, push the flap of the clip upwards to be able to
take the profile out of the clip.
Attention: It is recommended to mount the clip
with the flap forward (into the room). The clip can
only be mounted with the flap toward the window
or the pane respectively, in case the distance to
the rail is min. 7 mm.
>7 mm
Recommendation: DIN 7981 Ø 3,9 x 16 mm
(for wooden and synthetic frames)
Ceiling mounting with Clip
Profile
“Click”
Flap
Mount the clips 50 mm respectively from the end of the headrail,
and with a distance of max. 600 mm.
50 mm
22
16
50 mm
max. 600 mm
clip
mounting height min. 1,50 m!
min. 1,50 m!
Recommendation: DIN 7981 Ø 3,9 x 13 mm
(for wooden and synthetic frames)
1. 2. 3.