Seneca Z-KEY User manual

MI00580-1-EN INSTALLATION MANUAL 1/4
DOCUMENTATION
Z-KEY-P
DOCUMENTATION
Z-KEY
INSTALLATION MANUAL
Z-KEY
Z-KEY-P
SENECA s.r.l.; Via Austria, 26 – 35127 – PADOVA – ITALY; Tel. [phone] - Fax [phone]
WARNING: The full content of this manual must be read before any operation. The module must only be used by
qualied electricians. Specic documentation is available via QR-CODE shown on page 1.
Electrical and electronic waste disposal (applicable in the European Union and other countries with recycling).
The symbol on the product or its packaging shows the product must be surrendered to a collection centre
authorized to recycle electrical and electronic waste.
The module must be repaired and damaged parts replaced by the Manufacturer. The product is sensitive to
electrostatic discharges. Take appropriate measures during any operation.
PRELIMINARY WARNINGS
The word WARNING preceded by the symbol indicates conditions or actions that put the user's safety at risk.
The word ATTENTION preceded by the symbol indicates conditions or actions that might damage the
instrument or the connected equipment. The warranty shall become null and void in the event of improper use or
tampering with the module or devices supplied by the manufacturer as necessary for its correct operation, and if
the instructions contained in this manual are not followed.
CONTACT INFORMATION
Technical support [email protected] Product information [email protected]
This document is the property of SENECA srl. Copies and reproduction are prohibited unless authorised.
The content of this document corresponds to the described products and technologies.
Stated data may be modied or supplemented for technical and/or sales purposes.

MI00580-1-EN INSTALLATION MANUAL 2/4
MODULE LAYOUT
LED STATUS LED meaning
PWR ON The device is powered correctly
COM
Z-KEY-P version only
Flashing Pronet communication active
Off No Pronet communication
TX1 Flashing Data transmission on port #1 RS485
RX1 Flashing Data receipt on port #1 RS485
TX2 Flashing Data transmission on port #2 RS485/RS232
RX2 Flashing Data reception on port #2 RS485/RS232
ETH ACT Green Flashing Packet transmission on Ethernet port
ETH LNK Yellow ON Ethernet connection present
SIGNALS VIA LED ON FRONT PANEL
17.5 mm 111 mm
Dimensions: 17.5 x 102.5 x 111 mm, Weight: 100 g; Enclosure: PA6, black
102.5 mm
TECHNICAL SPECIFICATIONS
CERTIFICA-
TIONS
https://www.seneca.it/products/z-key/doc/CE_declaration
INSULATION
ENVIRONMENTAL
CONDITIONS
Temperature: -25 °C – + 65 °C; Humidity:;30%– 90% non condensing.
Altitude: Up to 2000 m above sea level; Storage temperature: -30 °C – + 85 °C
Protection rating: IP20 (Not evaluated by UL)
ASSEMBLY IEC EN60715, 35mm DIN rail in vertical position.
POWER SUPPLY Voltage: 11 – 40 Vdc; 19 – 28 Vac 50 – 60 Hz; Absorption: Max. 1,5W
Power
Supply
1500 Vac
11..40 Vdc / 19..28 Vac (IDC10)
ETH
Comm.
Comm. RS485
RS485/232
(IDC10)

MI00580-1-EN INSTALLATION MANUAL 3/4
FACTORY IP ADDRESS
The default module IP address is static: 192.168.90.101
WEB SERVER
To access the maintenance Web Server with 192.168.90.101 factory IP address:
Default user: admin, Default password: admin, http://192.168.90.101
The device may only be powered by a power supply unit with a limited energy electric circuit max.
40Vdc / 28Vac Max output in accordance with CAN/CSA-C22.2 No. 61010-1-12 / UL Std. No. 61010-1 (3rd Edi-
tion) chapter 6.3.1/6.3.2 and 9.4 or class 2 according to CSA 223/UL 1310.
ATTENTION
CONNECTIONS
3-way removable screw terminals, pitch 5 mm
Rear connector IDC10 for DIN bar 46277
RJ45 front connector
COMMUNICATION
PORTS
RS232 or RS485 switchable on terminal 10 - 11 - 12 (serial port 2)
Maximum Baud rate 115 k, maximum cable length RS232 < 3m
RS485 IDC10 rear connector: Maximum Baud rate 115 k. (serial port 1)
RJ45 front Ethernet connector: 100 Mbit/s, maximum distance 100 m
CONFIGURATION
Conguration and FW update via webserver;
Via DIP - SWITCH
Via EASY SETUP 2 conguration software
SETTING THE DIP-SWITCHES
RS232/RS485 SETTING: RS232 or RS485 conguration on terminals 10-11-12 (serial port 2)
SW2
1 ON RS232 ACTIVATION
0 OFF RS485 ACTIVATION
KEY
1 ON
0 OFF
SW2 DIP-SWITCH:
Through DIP-SWITCH-SW1 it is possible to set the IP conguration of the device:
DESCRIPTION DIP 1 DIP 2
To obtain the conguration from the Flash memory, both SW1
DIP switch selectors must be set to OFF
To reset the device to factory settings both SW1 DIP switches
must be set to ON
To force the device’s IP address to the standard value of
SENECA Ethernet products: 192.168.90.101
Reserved
IDC10 CONNECTOR
RS485GND
RS485A
RS485B
Power Supply AC / +
Power Supply AC / -
IDC 10
1
The illustration shows the meanings of the various IDC10
connector pins if signals are to be sent via them directly.
The DIP-switch settings are read only at boot time. At each change, perform a restart.
WARNING

MI00580-1-EN INSTALLATION MANUAL 4/4
INSTALLATION REGULATIONS
The module has been designed for vertical installation on a DIN 46277 rail. For optimal operation and long life,
adequate ventilation must be provided. Avoid positioning ducting or other objects that obstruct the ventilation slots.
Avoid mounting modules over heat-generating equipment. Installation in the bottom part of the electrical panel is
recommended.
These are open-type devices and intended for installation in an end enclosure / panel offering mechanical pro-
tection and protection against spread of re.
ATTENTION
ELECTRICAL CONNECTIONS
To meet the electromagnetic immunity requirements:
- use shielded signal cables;
- connect the shield to a preferential instrumentation earth system;
- separate shielded cables from other cables used for power installations (transformers, inverters, motors, etc...).
CAUTION
10
11
12
GND
A (+)
B (-)
10
11
12
GND
RX
TX
1
2
3
Vac/Vdc
Vac/Vdc
POWER SUPPLY SERIAL PORT 2: RS485
SW2 = OFF
SERIAL PORT 2: RS232
SW2 = ON
Use only copper or copper-clad aluminium or AL-CU or CU-AL conductors
ATTENTION
CAUTION
DO NOT USE DEVICES WITH THE SAME IP ADDRESS IN THE SAME ETHERNET NETWORK.
WEB SERVER
To access the maintenance Web Server with the factory IP address above, use the following credentials:
Username: admin; Password: admin
N.B.: For the Z-KEY-P version it is rst necessary to activate webserver mode
The device is normally in Pronet mode; in Pronet mode the device can be congured only through the Easy Setup 2 software.
In order to access the internal webserver it is necessary to put the device in Webserver mode using the Easy Setup 2 or Seneca
Device Discovery software. It is also possible to change the operating mode by pressing the side button following the procedure:
To force webserver mode:
• Keep the “PS1” button pressed until all LEDs are switched off
• Release the button
• The device restarts and the PWR and COM LEDs ash slowly to indicate webserver mode
To force Pronet mode:
• Keep the “PS1” button pressed until all LEDs are switched off
• Release the button
• The device restarts and the PWR and COM LEDs stop ashing slowly to indicate Pronet mode
WEB SERVER AND PROFINET MODE (Z-KEY-P)