Sensear SM1R User manual

DOC00076 – REV 01.0
ENGLISH
FRANÇAIS
ESPAÑOL
PORTUGUÊS

HEADSET INFORMATION
ENGLISH

DOC00076 SM1R Headset Information rev 01.0
2
English
FORWARD
Product Safety and RF Exposure Compliance:
This product is designed to be used in isolation or in conjunction with a
two way radio. Before using this product with a two-way radio, read the
operating instructions for safe usage contained in the Product Safety
and RF Exposure booklet enclosed with the two-way radio.
FCC COMPLIANCE STATEMENT
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for
help.

DOC00076 SM1R Headset Information rev 01.0
3
English
SPECIFICATIONS
SPECIFICATION
SM1R
Weight
400g
14.1oz
Operational Temperature
-20°C to
+45°C
32°F to
113°F
Power consumption
See radio cable documentation
Housing Material
PC, ABS + TPE
RoHS Compliant
Yes
NRR AND SLC80
The SM1R has been certified to International hearing protection
standards including AS/NZS 1270-2002, ANSI S3.19-1974, ANSI
S12.6-2008, EN352-1, EN352-3, EN352-4, and EN352-6. The following
passive attenuation ratings were observed:

DOC00076 SM1R Headset Information rev 01.0
4
English
PASSIVE ATTENUATION (ANSI S3.19 -1974)
SM1R measured in accordance with ANSI S3.19 -1974.
Headband mount-SM1RB001
Frequency (Hz)
125
250
500
1000
2000
3150
4000
6300
8000
NRR
Mean
attenuation (dB)
22.1
24.4
31.1
35.1
35.8
37.0
39.9
40.7
40.7
27 dB
Standard
deviation (dB)
3.1
2.4
2.0
2.5
3.2
3.0
3.3
2.7
2.9
Behind the neck mount-SM1RE001
Frequency (Hz)
125
250
500
1000
2000
3150
4000
6300
8000
NRR
Mean
attenuation (dB)
18.9
22.4
28.6
33.6
33.5
35.3
37.3
38.8
37.4
24 dB
Standard
deviation (dB)
3.5
3.4
2.6
2.8
2.3
3.5
4.0
2.9
3.4
Helmet mount-SM1RH001
Frequency (Hz)
125
250
500
1000
2000
3150
4000
6300
8000
NRR
Mean
attenuation (dB)
18.6
20.8
27.3
33.6
37.1
35.5
35.3
37.1
35.0
23 dB
Standard
deviation (dB)
3.2
2.7
3.1
3.9
2.3
3.1
3.8
3.8
3.4

DOC00076 SM1R Headset Information rev 01.0
5
English
PASSIVE ATTENUATION (ANSI S12.6 - 2008)
SM1R measured in accordance with ANSI S12.6 - 2008.
Headband mount-SM1RB001
Frequency (Hz)
125
250
500
1000
2000
4000
8000
NRR (SF)
Mean attenuation
(dB)
21.4
21.9
29.8
33.7
35.8
37.2
38.5
27 dB
Standard
deviation (dB)
3.0
2.1
1.7
2.8
1.5
1.9
2.8
APV 80
18.9
20.1
28.4
31.3
34.5
35.6
36.1
Behind the neck mount-SM1RE001
Frequency (Hz)
125
250
500
1000
2000
4000
8000
NRR (SF)
Mean attenuation
(dB)
18.7
19.9
28.0
34.1
31.5
35.6
35.3
24.3 dB
Standard
deviation (dB)
3.0
2.5
2.2
1.7
3.2
3.4
4.1
APV 80
16.2
17.8
26.2
32.7
28.8
32.7
31.9
Helmet mount-SM1RH001
Frequency (Hz)
125
250
500
1000
2000
4000
8000
NRR (SF)
Mean attenuation
(dB)
15.0
17.7
25.2
30.4
33.9
34.5
33.8
19.1 dB
Standard
deviation (dB)
6.5
6.7
6.6
4.0
3.3
5.9
5.1
APV 80
9.5
12.1
19.7
27.0
31.1
29.5
29.5

DOC00076 SM1R Headset Information rev 01.0
6
English
PASSIVE ATTENUATION (AS/NZS 1270:2002)
SM1R measured in accordance with AS/NZS 1270:2002.
Headband mount-SM1RB001
Frequency (Hz)
125
250
500
1000
2000
4000
8000
SLC (80)
Mean attenuation
(dB)
20.3
21.7
30.3
33.2
35.2
36.6
37.3
31dB,
Class 5
Standard deviation
(dB)
4.3
3.1
2.7
3.0
2.7
2.5
3.3
Mean attenuation –
Standard deviation
(dB)
16.0
18.6
27.6
30.2
32.5
34.1
34.0
Behind the neck mount-SM1RE001
Frequency (Hz)
125
250
500
1000
2000
4000
8000
SLC (80)
Mean attenuation
(dB)
19.3
20.0
27.0
33.7
30.5
33.9
33.0
27 dB,
Class 5
Standard deviation
(dB)
5.1
4.1
3.7
2.4
4.5
3.8
5.2
Mean attenuation –
Standard deviation
(dB)
14.2
15.9
23.3
31.3
26.0
30.1
27.8
Helmet mount-SM1RH001
Frequency (Hz)
125
250
500
1000
2000
4000
8000
SLC (80)
Mean attenuation
(dB)
15.6
19.1
24.7
29.7
34.0
34.5
33.4
26 dB,
Class 5
Standard deviation
(dB)
5.7
5.5
5.2
3.9
3.0
5.5
5.0
Mean attenuation –
Standard deviation
(dB)
9.9
13.6
19.5
25.8
31.0
29.0
28.4

DOC00076 SM1R Headset Information rev 01.0
7
English
PASSIVE ATTENUATION (EN352-1 AND EN352-3)
SM1R measured in accordance with EN352-1 and EN352-3.
Headband mount-SM1RB001 (EN352-1)
Frequency (Hz)
125
250
500
1000
2000
4000
8000
H
M
L
SNR
(dB)
Mean attenuation (dB)
22.5
24.5
31.5
34.9
35.8
38.0
39.8
35
30
24
33
Standard deviation (dB)
4.8
2.6
2.3
3.1
2.5
2.1
2.7
Mean attenuation –
Standard deviation
(dB)
17.7
21.9
29.2
31.8
33.3
35.9
37.1
Behind the neck mount-SM1RE001 (EN352-1)
Frequency (Hz)
125
250
500
1000
2000
4000
8000
H
M
L
SNR
(dB)
Mean attenuation (dB)
20.7
21.3
27.7
34.0
33.3
35.3
36.1
32
27
21
30
Standard deviation (dB)
5.1
3.3
3.1
2.5
2.9
2.3
2.6
Mean attenuation –
Standard deviation
(dB)
15.6
18.0
24.6
31.5
30.4
33.0
33.5
Helmet mount-SM1RH001 (EN352-3)
Frequency (Hz)
125
250
500
1000
2000
4000
8000
H
M
L
SNR
(dB)
Mean attenuation (dB)
20.4
22.2
28.2
33.5
36.9
38.0
37.5
34
28
22
31
Standard deviation (dB)
3.6
3.3
3.3
3.6
2.3
3.9
3.0
Mean attenuation –
Standard deviation
(dB)
16.9
18.8
24.9
29.8
34.6
34.1
34.6

DOC00076 SM1R Headset Information rev 01.0
8
English
The SM1R has level dependent facilities and the criterion levels as
defined in EN352-4 are displayed below:
Model
H
M
L
(dBA)
SM1R
108.6
104.6
103.4
TWO-WAY RADIO INPUT (EN352-6)
The electrical input level for which the mean plus one standard deviation
A-weighted diffused-field related sound pressure level is equal to 82
dB(A) is an RMS voltage U = 108 mV.
MAINTENANCE AND CLEANING
The headset is an active hearing protector that allows audible contact
with your surroundings while providing protection from harmful noise.
It is recommended that the headset is fitted, adjusted and maintained in
accordance with these instructions. This headset should be worn at all
times in noisy surroundings. The headset should be regularly inspected
for serviceability.
Warning:
•If these instructions are not followed the protection of the headset
will be severely impaired.
•Noise reduction will be adversely affected by anything that impairs
the seal of the earmuff cushions against the head, such as thick
spectacle frames and balaclavas
•The reported attenuation will be obtained only if the headset is in
good condition and worn as directed (Refer to AS/NZS 1269.3
for guidance).

DOC00076 SM1R Headset Information rev 01.0
9
English
•This product should not be used where there is a risk that the
connecting cord could be caught up during use.
•This product is provided with level-dependent in-ear audio
playback. The wearer should check correct operation before use.
If distortion, or failure is detected. The wearer should refer to the
manufacturer’s advice for maintenance and/or replacement.
Warning:
•Performance may deteriorate with battery usage. The typical
period of continuous use that can be expected from the headset
will depend on the two-way radio battery.
•The output of the level-dependent circuit of this hearing protector
may exceed the daily limit sound level. This limit can be adjusted
with a Sensear programming tablet.
•This headset has been tested and approved according to the
methods described in the EN352 series of standards.
SIZE RANGES
Warning- Ear-muffs complying with EN352-1 are of ‘small size range’,
‘medium size range’ or ‘large size range’. ‘Medium size range’ ear-muffs
will fit the majority of wearers. ‘Small size range’ or ‘large size range’ ear-
muffs are designed to fit wearers for whom ‘medium size range’ ear-
muffs are not suitable. The SM1R headband, SM1R behind-the-neck and
SM1R helmet adapters may be adjusted for small, medium or large size.

DOC00076 SM1R Headset Information rev 01.0
10
English
CLAMPING FORCE
The clamping force of the SM1R has been measured in accordance with
AS/NZS 1270:
Model Part # Units
Initial
measurements
Post-flex
measurements
A
B
C
A
B
C
SM1R -
Headband
mount
SM1RB001
Newtons
(N)
11.6 11.1 11.1 11.1 10.7 11.1
Pounds
(lbs)
2.6 2.5 2.5 2.5 2.4 2.5
SM1R - Behind
the neck mount
SM1RE001
N
14.2
14.7
14.2
14.2
14.7
14.2
lbs
3.2
3.3
3.2
3.2
3.3
3.2
SM1R - Helmet
mount
SM1RH001
N
9.3
9.3
9.3
9.3
8.9
9.3
lbs
2.1
2.1
2.1
2.1
2.0
2.1
MAINTENANCE AND STORAGE OF YOUR HEADSET
This product may be adversely affected by certain chemical substances.
Further information should be sought from the manufacturer.
The headset contains replaceable cushions (Part #: SMHK0000).
Cushions are recommended to be replaced every 3-6 months to
maintain the appropriate hearing protection that the product is certified
to. Cushions should be inspected regularly for signs of damage or wear.
Cushions can be removed simply by gripping the cushion and pulling firm-
ly to unclip from the baseplate. Replacement cushions may be pushed
into the clips around the baseplate.
The headset should be stored at room temperature (between
15°C/59°F and 25°C/77°F).

DOC00076 SM1R Headset Information rev 01.0
11
English
COPYRIGHT NOTICE
This document remains the property of Sensear Pty. Ltd. All rights
reserved. No part of this document may be reproduced in any form,
either in an electronic retrieval system or otherwise, without the prior
written consent of Sensear Pty. Ltd.
IMPORTANT NOTICE
Sensear Pty. Ltd. reserves the right to make corrections, modifications,
enhancement, improvements and other changes to its products and
services and to discontinue any product or service without notice.
Whilst Sensear Pty. Ltd. makes every effort to ensure that the
information in this document is correct at the time of publication, users
and potential users should first check with Sensear Pty. Ltd. to ensure
that they have received the most up-to-date documentation.
ACCESSORIES AND SPARE PARTS
SRCK6xxx
Various models, two-way radio interface cables for most
popular two way radios.
SMHK0000
Ear muff hygiene kits
SMBE0000
Behind-the-neck replacement band
SMBB0000
Headband replacement band
SMHA0001
SM1 Helmet Adaptor – MSA Vguard
SMHA0002
SM1 Helmet Adaptor – Protector Allsafe
SMHA0003
SM1 Helmet Adaptor – Protector Tuffmaster
SMHA0004
SM1 Helmet Adaptor – Unisafe Unilite
SMBM0001
Replacement boom microphone
SMAP0001
Cooling Pads

DOC00076 SM1R Headset Information rev 01.0
12
English
DECLARATION OF CONFORMITY
We, the undersigned,
Company
Sensear Pty Ltd
Address
199 Great Eastern Highway, Belmont, WA, 6104
Country
Australia
Telephone Number
[phone]
Fax Number
[phone]
Web
http://www.sensear.com
Email
[email protected]
Declare that:
Model SM1R in accordance with the following directives:
•89/686/EEC
•2014/53/EU
•2006/95/EC
•2004/108/EC
•2006/42/EC
Has been designed and manufactured to the following specifications:
•ETSI EN 352-1, EN352-3, EN352-4 and EN 352-6
•ETSI EN 301 489
•EN 55022
•EN 60950

INFORMATIONS RELATIVES AU
PROTECTEUR AUDITIF
FRANÇAIS

DOC00076 SM1R Informations relatives au protecteur auditif rev 01.0
2
Français
AVIS
Conformité du produit en matière de sécurité et d’exposition aux RF :
Ce produit est destiné à être utilisé seul ou conjointement avec un
émetteur-récepteur. Avant d’utiliser ce produit avec un émetteur-
récepteur, lisez les instructions de fonctionnement pour une utilisation
sûre contenues dans le livret Sécurité et exposition aux RF du produit
joint à l’émetteur-récepteur.
DECLARATION DE CONFORMITE FCC
Cet équipement a été testé et déclaré conforme aux limites pour un
appareil électrique de Classe B, en vertu de la partie 15 des
réglementations de la FCC. Ces limites sont destinées à fournir une
protection raisonnable contre les interférences nuisibles dans une
installation résidentielle. Cet équipement génère, utilise et peut propager
des ondes radioélectriques et, s’il n’est pas installé ou utilisé
conformément aux instructions, peut être à l’origine d’interférences
nuisibles avec les communications radio. Toutefois, il n’y a aucune
garantie qu’aucune interférence ne sera produite dans une installation
particulière. Si cet équipement est à l’origine d’une interférence nuisible
avec une réception radio ou télé, ce qui peut être vérifié en éteignant et
en allumant ledit équipement, l’utilisateur est encouragé à essayer de
corriger l’interférence à l’aide de l’une ou de plusieurs des mesures
suivantes:
•Réorienter ou repositionner l’antenne réceptrice.
•Augmenter la distance entre l’équipement et le récepteur.
•Brancher l’équipement à une prise reliée à un circuit différent
de celui du récepteur.
•Consulter le distributeur ou un technicien radio/télé
expérimenté.

DOC00076 SM1R Informations relatives au protecteur auditif rev 01.0
3
Français
SPÉCIFICATIONS
SPÉCIFICATIONS
SM1R
Poids
400g
14.1oz
Température opérationnelle
-20°C à +45°C
32°F à 113°F
Matériau extérieur
PC, ABS + TPE
Conformité RoHS
Oui
NRR AND SLC80
Le SM1R a été déclaré conforme aux normes de protection auditive
internationales, dont AS/NZS 1270-2002, ANSI S3.19-1974, ANSI
S12.6-2008, EN352-1, EN352-3, EN352-4 et EN352-6. Les taux
d’atténuation passive suivants ont été observés :

DOC00076 SM1R Informations relatives au protecteur auditif rev 01.0
4
Français
ATTENUATION PASSIVE (ANSI S3.19 -1974)
SM1R mesuré en conformité avec ANSI S3.19 -1974.
Port avec serre-tête-SM1RB001
Audiofréquence
(Hz)
125
250
500
1000
2000
3150
4000
6300
8000
NRR
Atténuation
moyenne (dB)
22.1
24.4
31.1
35.1
35.8
37.0
39.9
40.7
40.7
27 dB
SD (dB)
3.1
2.4
2.0
2.5
3.2
3.0
3.3
2.7
2.9
Port derrière le cou-SM1RE001
Audiofréquence
(Hz)
125
250
500
1000
2000
3150
4000
6300
8000
NRR
Atténuation
moyenne (dB)
18.9
22.4
28.6
33.6
33.5
35.3
37.3
38.8
37.4
24 dB
SD (dB)
3.5
3.4
2.6
2.8
2.3
3.5
4.0
2.9
3.4
Port avec casque-SM1RH001
Audiofréquence
(Hz)
125
250
500
1000
2000
3150
4000
6300
8000
NRR
Atténuation
moyenne (dB)
18.6
20.8
27.3
33.6
37.1
35.5
35.3
37.1
35.0
23 dB
SD (dB)
3.2
2.7
3.1
3.9
2.3
3.1
3.8
3.8
3.4

DOC00076 SM1R Informations relatives au protecteur auditif rev 01.0
5
Français
ATTENUATION PASSIVE (ANSI S12.6 - 2008)
SM1R mesuré en conformité avec ANSI S12.6 - 2008.
Port avec serre-tête-SM1RB001
Audiofréquence
(Hz)
125
250
500
1000
2000
4000
8000
NRR (SF)
Atténuation
moyenne (dB)
21.4
21.9
29.8
33.7
35.8
37.2
38.5
27 dB
SD (dB)
3.0
2.1
1.7
2.8
1.5
1.9
2.8
APV 80
18.9
20.1
28.4
31.3
34.5
35.6
36.1
Port derrière le cou-SM1RE001
Audiofréquence
(Hz)
125
250
500
1000
2000
4000
8000
NRR (SF)
Atténuation
moyenne (dB)
18.7
19.9
28.0
34.1
31.5
35.6
35.3
24.3 dB
SD (dB)
3.0
2.5
2.2
1.7
3.2
3.4
4.1
APV 80
16.2
17.8
26.2
32.7
28.8
32.7
31.9
Port avec casque-SM1RH001
Audiofréquence
(Hz)
125
250
500
1000
2000
4000
8000
NRR (SF)
Atténuation
moyenne (dB)
15.0
17.7
25.2
30.4
33.9
34.5
33.8
19.1 dB
SD (dB)
6.5
6.7
6.6
4.0
3.3
5.9
5.1
APV 80
9.5
12.1
19.7
27.0
31.1
29.5
29.5

DOC00076 SM1R Informations relatives au protecteur auditif rev 01.0
6
Français
ATTENUATION PASSIVE (AS/NZS 1270:2002)
SM1R mesuré en conformité avec AS/NZS 1270:2002.
Port avec serre-tête-SM1RB001
Audiofréquence
(Hz)
125
250
500
1000
2000
4000
8000
SLC (80)
Atténuation
moyenne (dB)
20.3
21.7
30.3
33.2
35.2
36.6
37.3
31dB,
Class 5
SD (dB)
4.3
3.1
2.7
3.0
2.7
2.5
3.3
Atténuation
moyenne - SD (dB)
16.0
18.6
27.6
30.2
32.5
34.1
34.0
Port derrière le cou-SM1RE001
Audiofréquence
(Hz)
125
250
500
1000
2000
4000
8000
SLC (80)
Atténuation
moyenne (dB)
19.3
20.0
27.0
33.7
30.5
33.9
33.0
27 dB,
Class 5
SD (dB)
5.1
4.1
3.7
2.4
4.5
3.8
5.2
Atténuation
moyenne - SD (dB)
14.2
15.9
23.3
31.3
26.0
30.1
27.8
Port avec casque-SM1RH001
Audiofréquence
(Hz)
125
250
500
1000
2000
4000
8000
SLC (80)
Atténuation
moyenne (dB)
15.6
19.1
24.7
29.7
34.0
34.5
33.4
26 dB,
Class 5
SD (dB)
5.7
5.5
5.2
3.9
3.0
5.5
5.0
Atténuation
moyenne - SD (dB)
9.9
13.6
19.5
25.8
31.0
29.0
28.4

DOC00076 SM1R Informations relatives au protecteur auditif rev 01.0
7
Français
ATTENUATION PASSIVE (EN352-1 AND EN352-3)
SM1R mesuré en conformité avec EN352-1 and EN352-3.
Port avec serre-tête-SM1RB001
Audiofréquence (Hz)
125
250
500
1000
2000
4000
8000
H
M
L
SNR
(dB)
Atténuation moyenne
(dB)
22.5
24.5
31.5
34.9
35.8
38.0
39.8
35
30
24
33
SD (dB)
4.8
2.6
2.3
3.1
2.5
2.1
2.7
Atténuation moyenne -
SD (dB)
17.7
21.9
29.2
31.8
33.3
35.9
37.1
Port derrière le cou-SM1RE001
Audiofréquence (Hz)
125
250
500
1000
2000
4000
8000
H
M
L
SNR
(dB)
Atténuation moyenne
(dB)
20.7
21.3
27.7
34.0
33.3
35.3
36.1
32
27
21
30
SD (dB)
5.1
3.3
3.1
2.5
2.9
2.3
2.6
Atténuation moyenne -
SD (dB)
15.6
18.0
24.6
31.5
30.4
33.0
33.5
Port avec casque-SM1RH001
Audiofréquence (Hz)
125
250
500
1000
2000
4000
8000
H
M
L
SNR
(dB)
Atténuation moyenne
(dB)
20.4
22.2
28.2
33.5
36.9
38.0
37.5
34
28
22
31
SD (dB)
3.6
3.3
3.3
3.6
2.3
3.9
3.0
Atténuation moyenne -
SD (dB)
16.9
18.8
24.9
29.8
34.6
34.1
34.6