Server BP-1 User manual

For purchasing our Eco Pump™.
This quality, NSF listed pump delivers precise
portions and is a reliable alternative to the constant
expense of disposable pumps.
CONSISTENT PORTIONS—SERVE BETTER
Thank You
Eco Pump™
MODEL: BP-1
88220

Page 2
PARTS FOR PUMP 88220
HEAD
ASSEMBLY
89215
CYLINDER
ASSEMBLY
88496
SEAL ASSEMBLY
100345
PISTON
DISCHARGE
TUBE
PINCH VALVE
88203
SPRING
88166
CAP
88016
CYLINDER
88247
STAINLESS STEEL BALL
1/2"DIAMETER
06022
(Ball snaps inside cylinder
and can always remain
installed, even during cleaning.)
FOOD
EQUIPMENT
LUBRICANT
40179
21"X 2/5"BRUSH
82526
11"BRUSH
82049
PUMP DELIVERS
1 OZ PORTIONS
To reduce portion, add
GAGING COLLAR(S)
88887 Small collar: 1/8 oz reduction
88888 Medium collar: 1/4 oz reduction
88879 Large collar: 1/2 oz reduction
LOCKING COLLAR
None 1oz
1Sm 7/8oz
1Med 3/4oz
1Lg 1/2oz
1Lg+1Med 1/4oz
1Lg+1Med+1Sm 1/8oz
COLLAR(S) USED PORTION RESULTS
2.5"EXTENSION TUBE
88315
If needed: Add to bottom
of Cylinder Assembly
to extend length.

Page 3
SAFETY
According to food and safety regulations, most
foods must be stored and/or served at certain
temperatures or they could become hazardous.
Check with local food and safety regulators for
specicguidelines.
Be aware of the product you are serving and the
temperature the product is required to maintain.
Server Products, Inc. cannot be responsible for the
serving of potentially hazardous product.
IMPORTANT
Clean, rinse, sanitize, and dry parts daily or regularly to
comply with local sanitization requirements.
NSF International lists this pump as:
“Not acceptable for dispensing potentially
hazardous foods.”
DISASSEMBLY
REMOVE SPRING, CAP &
EXTENSION TUBE FROM
CYLINDER
3
SEPARATE CYLINDER
ASSEMBLY & HEAD
Loosen locking collar to release.
2
REMOVE PUMP
from container of product.
1
During disassembly, collect small parts in
a container to prevent loss.
DISASSEMBLE AND WASH
ALL PARTS PROPERLY BEFORE USE. See page 4.
REMOVE ANY
GAGING COLLAR(S)
if necessary for cleaning.
7
REMOVE SEAL
from head assembly by pressing it
down and off with thumb.
Do not use a sharp tool.
5
REMOVE PINCH VALVE
from head assembly.
4
REMOVE O-RING
FROM SEAL
6

Page 4
CLEANING
RINSE
fully with clear water.
3
SANITIZE
all parts according to local sanitization
requirements. All parts in contact with food
must be sanitized.
4
AIR DRY
all parts fully.
5
Use dishwashing soap,
hot water
and nylon brush
YES!
DISASSEMBLE & CLEAN
all washable parts with soap and hot water
(See DISASSEMBLY on page 3.)
2
FLUSH & RINSE
all pump surfaces with hot water.
Place lower end of pump into container
of hot water and operate pump until all
remaining product is expelled and only hot
water is discharged.
1
Pump is dishwasher safe.
USE SUPPLIED BRUSH
to thoroughly clean inside discharge
tubeandanyconnedareas.

Page 5
• Fully rinsing and drying all parts can help
prevent corrosion. Elements and minerals in
tap water can accumulate on stainless steel
parts and create corrosion.
• Do not use abrasive, caustic or ammonia
based cleansers.
• Do not use products containing acids,
alkalines, chlorine, or salt. These agents can
corrode stainless steel.
• Do not use metal scrapers or cleaning pads
that could scratch surfaces.
• A mildly abrasive nylon or brass brush may
be used to remove any stubborn deposits.
This durable pump includes
stainless steel components.
If you notice corrosion beginning on any
stainless steel surface, you may need to change
the cleansing agent, sanitizing agent, or the
cleaning procedures you are using.
CARE OF STAINLESS STEEL
CLEAN-IN-PLACE PROCEDURE FOR PUMPS
CLEAN
• Pump out all (if any) remaining food
product from inside pump body.
• Wash and rinse off outside of pump body.
• Flush out and rinse inside of pump.
• Place lower end of pump into container
full of water and operate pump until all (if
any) remaining product is expelled
 andonlywarmwaterowsfromdischarge
tube.
• Mix 2 tsp (5 mL) of dishwashing detergent
with 1 quart (.95 L) of hot tap water
(approximately 110°F/43°C).
• Place lower end of pump into cleaning
mixture. Pump until all cleaning mixture is
expelled.
1
RINSE
• Place lower end of pump into 2 cups
(.5 L) of hot tap water (approximately
110°F/43°C) and pump until all tap
water is expelled.
2
RINSE
• Place lower end of pump into 1 cup
(.24 L) of hot tap water (approximately
110°F/43°C) and pump until all tap
water is expelled.
4
SANITIZE
• Mix one 1 oz (30 mL) packet of KAY-5
Sanitizer/Cleaner (EPA REG No. 5389-
15) with 2.5 gallons (9.5 L) of tap water
(approximately room temperature).
• Place lower end of pump into this
sanitizing mixture and repeatedly operate
pump until 1 quart (.95 L) sanitizing
mixture is pumped through pump.
3

Page 6
ASSEMBLY PRACTICE SAFETY. WASH ALL PARTS
PROPERLY BEFORE USE. See page 4.
INSTALL O-RING
into seal.
Apply food equipment
lubricant on O-ring
1
INSTALL SEAL
onto head assembly piston.
Apply small amount of food equipment
lubricant inside seal.
TIP: Flared end of seal should face
away from piston head.
2
INSTALL PINCH VALVE
TIP: Squeeze the pinch valve open
before installation to ensure it isn’t
stuck shut.
Install pinch valve into bottom of piston.
Press pinch valve securely to seal end.
3
INSERT SPRING
INTO CYLINDER
4
SNAP!
OPTIONAL: ADD GAGING COLLAR(S)
to reduce portion size.
Small collar: 1/8 oz reduction
Medium collar: 1/4 oz reduction
Large collar: 1/2 oz reduction
OPTIONAL: ADD EXTENSION TUBE
to bottom of cylinder if extra length
will be needed to reach product
at bottom of container.
SNAP CAP
ONTO CYLINDER
Pressrmlytosecurecapdown
over all threading on cylinder.
5

Page 7
INSTALL HEAD ASSEMBLY
INTO CYLINDER
Apply a small amount of food equipment
lubricant to the outside of seal.
Slide locking collar down
onto cylinder threading.
Tightenrmlytosecure
head assembly to cylinder.
6
PRIME PUMP
Press pump several times until any air
bubbles are eliminated and only product
is dispensed.
8
INSERT & SECURE PUMP
to product container.
Tightencapveryrmlyontoproduct
container threading.
7

Page 8 Manual EM_01939_RevC 072623
TROUBLESHOOTING
INCONSISTENT PORTIONS?
• Ensure product container is not empty
and has enough product to pump.
• Clean pump.
• Ensure unit is assembled correctly.
TIP: Seal has a slight taper.
Install with at side towards
top, ared side down.
• Ensure pinch valve is
installed correctly.
TIP: Squeeze the pinch valve
open before installation to
ensure it isn’t stuck shut.
• Ensure that the spring is functional.
Replace broken spring if necessary.
• Ensure that the stainless steel ball
is snapped in place below tabs.
PRODUCT OOZES OUT FROM LOCKING COLLAR?
• Ensure that the cap is securely snapped
into place below all the threading on
the cylinder.
SNAP!
NEED HELP?
Please be prepared with your Model, P/N and
Series located on the lid or base of the unit.
Example:
Chat with us!
[email protected]
262.628.5600 | 800.558.8722
Server Products Inc.
3601 Pleasant Hill Road
Richfield, WI 53076 USA MODEL
XXXX
P/N
#####
SERIES
##X ##X
SERVER PRODUCTS
LIMITED WARRANTY
This Server product is backed by a two-year
limited warranty against defects in materials and
workmanship. See Server-Products.com for details.
GENERAL SERVICE,
REPAIR OR RETURNS
Before sending an item to Server Products, contact Customer
Care to request a Return Authorization Number. The RA Number
ensures proper processing and a prompt turnaround. Repaired
units are typically shipped out within 48 hours of receipt.
Merchandise returned for credit will incur a 20% restocking
charge, must be less than 90 days old, and in unused (new)
condition. Electrical parts (thermostats, heating elements, etc.)
are not returnable.
Servicing Cord:Specictoolsarerequiredforsafeandproper
power supply cord removal and installation. Repairs should be
donebyanOEMrepresentativeorqualiedtechnicianusinga
cord meeting code H05 RN-F requirements.