Seville Classics UltraHD 20157 User manual

TR170815
ASSEMBLY INSTRUCTIONS
UltraHD® Workcenter
48 in W X 24 in D X 65.5 in H
(1.21 m x 60.9 cm x 1.66 m)
LED work light included
(Model No. 20157)
Reference page 8 for special care and
maintenance of stainless steel

Drawer
Top Cantilever Shelf
No. Qty. No. Qty.
#1 1PC #20-5 1PC
#2-C 1PC #20-6 1PC
#3-B 1PC #20-7 DRAWER DIVIDER 2PCS
#3-C 1PC #44 1PC
#5-B 2PCS #46-1 TOP CANTILEVER SHELF BACK PANEL 1PC
#6 4PCS #46-2 TOP CANTILEVER SHELF BASE PANEL 1PC
#18 1PC #46-3 TOP CANTILEVER SHELF LEFT PANEL 1PC
#18-1 TOP CANTILEVER SHELF MAT 1PC #46-4 TOP CANTILEVER SHELF RIGHT PANEL 1PC
#19-2 DRAWER BASE PANEL 1PC #47 "L" BRACKET 8PCS
#20-1 DRAWER FRONT PANEL 1PC #48-2 SMALL DRAWER LEFT SUPPORT 1PC
#20-3 DRAWER LEFT PANEL 1PC #48-3 SMALL DRAWER RIGHT SUPPORT 1PC
#20-4 DRAWER RIGHT PANEL 1PC #49 PEGBOARD LONG SUPPORT BAR 2PCS
DRAWER MAT
BOTTOM PEGBOARD PANEL
Parts
Parts
LEG PIECE
LED LAMP
PARTS LIST (pg 1 of 9)
Please check the parts carefully according to the parts list. If you are missing any parts, please contact our
customer service department (please refer to page 9 of 9).
SOLID HARDWOOD BOARD TOP
TOP PEGBOARD PANEL
BOTTOM CROSSBAR
DRAWER BACK PANEL
DRAWER FRONT PANEL SUPPORT PLATE
LEVELING FOOT

No. Qty. No. Qty.
#15 36PCS #100 4PCS
#21 1PC #101 4PCS
#25 1PC #102 4PCS
#27-B 10PCS #103 4PCS
#40 10PCS #104 2PCS
#41 29PCS #105 2PCS
#45 1PC #106 2PCS
#50 48PCS #107 1PCS
#51 4PCS
STUD SCREW J
2" DOUBLE PRONG
4" CURVED DOUBLE PRONG
2" PLIER HOLDER
2" MULTI-TOOL HOLDER
POWER STRIP W. USB PORTS
PARTS LIST (pg 2 of 9)
Please check the parts carefully according to the parts list. If you are missing any parts, please contact our
customer service department (please refer to page 9 of 9).
1" STRAIGHT
1.5" STRAIGHT
WRENCH
WASHER
1/2" CURVED
Parts
1" CURVED
Parts
SCREW B (M4 x 8L)
SCREW DRIVER
SCREW I (M6 x 15L)
SCREW F (M4 x 8L)
SCREW E(M8 x 18L)
#15
#50
#27-B
#40
#41
#51
#21
#25
#45
#100 #101 #102 #103 #104
#105 #106 #107
M8X20 pcs

Step 1.
Step 2.
NOTE:
Step 3.
NOTE:
Install (#5-B) Leg Piece.
A: Open the package, and put the parts aside. Then, attach the (#47) "L" Bracket to the (#5-B) Leg Piece, use (#50)
Screw I to tighten. Repeat Step A to install (#47) "L" Brackets to another one (#5-B) Leg Piece.
Note: Tighten the all the screws after the (#47) Brackets are flush with the (#5-B) Leg Piece.
TIP: A magnetic screwdriver is included for your convenience. If a power screwdriver is used, keep on a low torque
setting.
ASSEMBLY INSTRUCTIONS (pg 3 of 9)
*NOTE: We recommend TWO people to assemble the workbench.
Turn the workbench upright once you finish this step.
Do not fully tighten the screws. This will help you
make any adjustments for alignment.
B: Attach the (#5-B) Leg Pieces to the back of the (#1) Solid Hardwood Board Top, line up the screw holes, use (#50)
Screw I and (#21) Screwdriver to tighten.
Note: Assemble the workcenter on top of the cardboard packaging to help avoid scratching the solid hardwood top.
Install (#48-2) Small Drawer Left Support, (#48-3)
Small Drawer Right Support.
Attach the (#48-2) Small Drawer Left Support to the
bottom of (#1) Solid Hardwood Board, line up the screw
holes, use (#50) Screw I and (#21) Screwdriver to
tighten.
Repeat this step to install (#48-3) Small Drawer Right
Support.
Install (#3-B) Bottom Cross Bar and (#6) Leveling
Feet.
Attach the (#3-B) Bottom Cross Bar to the back of (#5-B)
Leg Piece, line up the screw holes, use (#40) Screw E
with (#27-B) Washer and (#25) Wrench to tighten.
After installing (#5-B) Leg Pieces, attach (#6) Leveling
Feet to (#5-B) Leg Pieces, use (#25) Wrench to tighten.
A
B
Back

Step 4.
Step 5.
Step 6. Install (#46) Top Cantilever Shelf .
Step 7.
Install Assembled (#46) Top Cantilever Shelf to
workbench.
Attach assembled (#46) Top Cantilever Shelf to (#2-C) Top
Pegboard Panel and (#49) Pegboard Long Support Bars, line up
the screw holes, use (#41) Screw F to tighten. Use (#15) Screw B
to fasten the (#2-C) Top Pegboard and (#46) Top cantilever Shelf.
NOTE: Do not fully tighten the screws. This will help you make
any adjustments for alignment later.
ASSEMBLY INSTRUCTIONS (pg 4 of 9)
*NOTE: We recommend TWO people to assemble the workbench.
A). Attach the (#46-3) Top Cantilever Shelf Left Panel and the
(#46-4) Top Cantilever Shelf Right Panel to (#46-2) Top Cantilever
Shelf Base Panel. Use (#41) F screws to tighten.
NOTE: Do not fully tighten the screws. This will help you make
any adjustments for alignment later.
B). Make sure to slide the back panel underneath the edge of
(#46-2) Top Cantilever Shelf Base Panel. Use (#41) F screws to
tighten.
Install (#49) Pegboard Long Support Bar.
Attach (#49) Pegboard Long Support Bar to the back of the
workbench, line up the screw holes, use (#40) Screw E with (#27-
B) Washer to tighten.
NOTE: Do not fully tighten the screws. This will help you make
any adjustments to alignment later.
Install (#3-C) Bottom Pegboard Panel and (#2-C) Top
Pegboard Panel.
Attach (#3-C) Bottom Pegboard Panel along the back top edge of
workbench and against (#49) Pegboard Long Support Bar, line
up the screw holes, use (#41) Screw F and (#21) Screwdriver to
tighten. Use (#15) Screw B to fasten the (#2-C) & (#3-C) Top &
Bottom Pegboard.
NOTE: Do not fully tighten the screws. This will help you make
any adjustments to alignment later.
Attach (#2-C) Top Pegboard Panel to the top of (#3-C) Bottom
Pegboard Panel and (#49) Pegboard Long Support Bar, line up
the screw holes, use (#41) Screw F and (#21) Screwdriver to
tighten.
A
B

Step 8.
Step 9.
Step 10.
Note:
ASSEMBLY INSTRUCTIONS (pg 5 of 9)
*NOTE: We recommend TWO people to assemble the workbench.
Install (#20-3 & #20-4) Left & Right Drawer Side Panels
and (#20-5) Drawer Back Panel.
Attach (#20-3 & #20-4) Left & Right Drawer Side Panels and
(#20-5) Drawer Back Panel to the (#19-2) Drawer Base
Panel. Line up the screw holes and use (#15) Screw B to
tighten.
NOTE: Do not fully tighten the screws until next step had
finish.
Install (#20-6) Drawer Front Panel Support Plate
Attach (#20-6) Drawer Front Panel Support Plate as the left
arrow shows. Line up the screw holes and use (#15) Screw B
to tighten.
NOTE: Once you adjust all the parts in position, tighten all
screws.
Install (#20-1) Drawer Front Panel
Attach the Drawer Case to the (#20-1) Drawer Front Panel.
Line up the screw holes and use (#15) Screw B to tighten.
Drawer's maximum loading capacity is 60 lbs to avoid
the unit from tipping when drawer is fully extended.

Step 11. Insert Drawer
WARNING:
NOTE:
Step 12.
Place (#18) Drawer Mat
After sliding in the Drawer, place (#18) Drawer
Mats inside the drawer or you can place the (#18)
Drawer Mat inside the drawer before you slide
them in.
ASSEMBLY INSTRUCTIONS (pg 6 of 9)
*NOTE: We recommend TWO people to assemble the workbench.
Once you insert the drawers, tighten (#15) Screw
B for (#48-2) Small Drawer Left Support and (#48-
3) Small Drawer Right Support.
Pull out the drawer sliders and inner ball bearing
track completely. Then attach and fit the Drawer
to the inner track of the sliders and slide drawers
in.
Pull out the Ball Bearing track towards you.
Pull out slides

Step 11.
NOTE:
Step 12. Install (#44) LED Lamp.
Step 13. Place (#45) Power Strip.
You can assemble this step before or after the
drawer is assembled on the Workbench
How to remove the Drawer Divider
Insert Drawer Divider into the drawer. The solid
wall of the divider should be facing the desired
slot position. Slide the divider towards the slot,
then push down into the slots.
Repeat the above steps to assemble another
Drawer Divider.
Make sure the power cord goes through Rubber
Grommet of (#2-C) Top Pegboard Panel. Attach
(#44) LED Lamp under the assembled (#46) Top
Cantilever Shelf. Line up the screw holes, use
(#15) Screw B to tighten. Then place the (#18-1)
Top Cantilever Mat in place.
NOTE: You can position (#45) Power Strip on
the left or right side of the (#3-C) Bottom
Pegboard Panel.
Insert and screw (#51) Stud Screw J to (#3-C)
Bottom Pegboard Panel, then, hook (#45) Power
Strip on and make sure the power cord goes
through Rubber Grommet of (#3-C) Bottom
Pegboard Panel.
Lift the Drawer Divider up and to the side to remove from
the slot.
ASSEMBLY INSTRUCTIONS (pg 7 of 9)
*NOTE: We recommend TWO people to assemble the workbench.
Install (#20-7) Drawer Divider

Step 14.
UltraHD Wood Top
Restore Shallow Scratches or Chips
Applying a Polyurethane Coating
Please follow the manufacturer's instruction on the product for application.
Stainless Steel Maintenance:
These parts have an UltraGuard™ fingerprint resistant finish. Do not use traditional stainless steel cleaners on this unit. Lightly
wipe off once a month with clean warm water and a soft cloth (preferably a microfiber cloth). This is the safest formula to
prevent new stains from appearing over time and manage unwanted fingerprints or grease marks. Remember to always wipe in
the direction of the surface grain (NEVER ACROSS) and always use a lint-free cloth. Once the surface is clean,thoroughly wipe dry
with a soft absorbent cloth.
If the wood top becomes scratched and chipped over time or during assembly, a Polyurethane finish can be applied to help
restore the wood's natural texture, as well as protect the surface from future damage.
ASSEMBLY INSTRUCTIONS (pg 8 of 9)
*NOTE: We recommend TWO people to assemble the workbench.
Although great care is taken to hand select consistent wood top color and grain for UltraHD products, there can and will be
natural variations in color and graining between finished products. These variations contribute to the beauty of using a natural
material as a workbench and are considered standard quality. Variations of color within these standards and minor scratches in
the clear coat finish will not be a reason for replacement. If the wood top is received with excessive damage or splitting, Seville
Classics will guarantee replacement of the wood top.
Place (#100), (#101), (#102), (#103), #104),
(#105), (#106), (#107) Hooks to Pegboard as
you desire.
[!] CAUTION: Potential Shock or Fire Hazard. This unit is
not intended for use in wet or potentially wet locations,
such as showers, saunas, under or near fishtanks, sinks,
etc.

customer service department at:
USA
Fax: [phone]
E-mail: [e-mail]
Website & Online Store: www.sevilleclassics.com
CONTACT INFORMATION (pg 9 of 9)
Telephone: [phone] within USA
Hours: 9:00am - 4:30pm (Pacific Standard Time)
please contact our bilingual (English/Spanish)
Seville Classics, Inc.
19401 South Harborgate Way
*If you are missing any parts, have any questions, or need additional assistance in assembly,
Torrance, CA 90501

UltraHD Line
Model No. 20150
UltraHD Wall Cabinet
Model No. 20156
UltraHD Workbench
Model No. 20152
UltraHD Rolling Workbench
Model No. 20158
UltraHD Storage Cabinet
Model No. 20153
UltraHD Storage Cabinet