Seville Classics UltraHD 20143 User manual

TR200228
ASSEMBLY INSTRUCTIONS
Storage Cabinet (Model No. 20143)
36in.W X 18in. D X 72in. H
(91.4cm x 45.7cm x 1.83m)
Reference page 12 for special
care and maintenance of
stainless steel

(pg 1 of 13)
#55-A

(pg 2 of 13)
(#1-A) Left Side Panel
(#2-A) Right Side Panel
(#6-A) Left Door
(#7-A) Right Door

Please check the parts carefully according to the parts list.
(#4) Bottom Panel x 1 PC
(#5) Middle Shelf x 3 PCS
PARTS LIST (pg 3 of 13)
(#1-A3) Side Panel Reinforcement Connection Part x 2 PCS
(#2-A1) Right Side - Upper Panel x 1 PC
(#1-A1) Left Side - Upper Panel x 1 PC
(#1-A2) Left Side - Bottom Panel x 1 PC
(#2-A2) Right Side - Bottom Panel x 1 PC
(#3) Top Panel x 1 PC

(#9) Middle Back Panel x 2 PCS
(#6-A1) Left Door - Upper Panel x 1 PC
(#6-A2) Left Door - Bottom Panel x 1PC
(#6-A3) Door Panel Connection Part x 2 PCS
(#7-A2) Right Door - Bottom Panel x 1 PC
(#7-A3) Key Rod x 1 PC
(#8) Upper Back Panel x 1 PC
PARTS LIST (pg 4 of 13)
Please check the parts carefully according to the parts list.
(#7-A1) Right Door - Upper Panel x 1 PC

(#17-1) Middle Corner Protection x 2 PCS
(#34) HOOK x 12 PCS
(#23) Magnet x 2 PCS
PARTS LIST (pg 5 of 13)
Please check the parts carefully according to the parts list.
(#16-1) Corner Protection - B x 1 PC
(#12) Wheel with Brake x 2 PCS
(#13) Wheel W/O Brake x 2 PCS
(#10) Bottom Back Panel x 1 PC
(#15-1) Corner Protection - A x 1 PC

(#21) Screw Driver x 1 PC
(#41) Screw F (M4 x 8L) x 86 PCS
(#52) Screw K (M5 x 10L) x 8 PCS
(#42) Screw G (M4 x 30L) x 12 PCS
(#53) Screw L (M4 x 6L) x 1 PC
(#54) Screw N (M4 x 10L) x 18 PCS
PARTS LIST (pg 6 of 13)
Please check the parts carefully according to the parts list.
(#58) Bumper x 4 PCS
(#22) Key x 2 PCS

(#61) Screw O (M4 x 12L) x 2 PCS
(#60) Mounting Strap x 2 PCS
(#27) WASHER (M4) x 2 PCS
(#27-B) WASHER (M8)x 2 PCS
(#55) Screw M (M6 x 50L) x 2 PCS
(#55-A) Wall Anchor x 2 PCS
PARTS LIST (pg 7 of 13)
Please check the parts carefully according to the parts list.
(#17) Screw D (M8x18L) x 16 PCS
(#16) Screw C (M4x18L) x 16 PCS
M8X20 pcs

TIP:
WARNING:
Step 1: Install (#1-A) Left Side Panel.
Note:
Step 2: Install (#2-A) Right Side Panel.
Step 3: Install (#6-A) Left Door.
Note:
1). Place (#6-A1) Left Door - Upper Panel and (#6-A2)
Left Door - Bottom Panel together, line up screw holes,
use 1pc (#41) Screw F to tighten from the side.
2). Place the (#6-A3) Door Panel Connection Part over
the touching sides, line up the screw holes, use 4pcs
(#41) Screw F to tighten from the top, and use 4pcs
(#52) Screw K to tighten from outside edge.
Make sure the (#6-A1) Left Door - Upper Panel is
flushed with (#6-A2) Left Door - Bottom Panel.
Repeat Step 1, use (#2-A1) Right Side Upper Panel,
(#2-A2) Right Side Bottom Panel, (#1-A3) Side Panel
Reinforcement Connection Part 3pcs (#42) Screw G to
tighten from the side, then use 4pcs (#41) Screw F to
tighten from the top side.
ASSEMBLY INSTRUCTIONS (pg 8 of 13)
Storage Cabinet (Model No. 20143)
Some parts may have sharp edges. To avoid injury,
wearing gloves is recommended during assembly.
This package contains an updated product
construction designed for easier transportation
while maintaining a rigid structure.
Maximum loading capacity is 600LBS.
A magnetic screwdriver is included for your
convenience. If a power screwdriver is used, keep
on a low torque setting.
Make sure the (#1-A1) Left Side Upper Panel is flushed
with (#1-A2) Left Side Bottom Panel.
Place the (#1-A1) Left Side - Upper Panel and (#1-A2)
Left Side - Bottom Panel together, place the (#1-A3)
Side Panel Reinforcement Connection Part over the
touching edges, line up screw holes, use 3pcs of (#42)
Screw G to tighten from the side, then use 4pcs of
(#41) Screw F to tighten from the top side.

Step 4: Install (#7-A) Right Door.
Note:
Step 5: Install (#7-A3) Key Rod.
Step 6: Install (#3) Top Panel to (#1-A1) Left Side Upper
Panel and (#2-A1) Right Side Upper Panel.
Note:
Step 7: Install (#4) Bottom Panel to (#1-A2) Left Side Bottom
Panel and (#2-A2) Right Side Bottom Panel.
Note:
Before tightening screws, make sure the bottom
corners of (#1-A1, #2-A1) Left Side Upper Panels are
completely flushed with the back and front corners of
(#3) Top Panel.
Attach (#4) Bottom Panel to (#1-A2) Left Side Bottom
Panel and (#2-A2) Right Side Bottom Panel. Make sure
the front of the bottom panel faces downward. Line up
screw holes, use 6pcs (#42) Screw G to tighten.
Before tightening screws, make sure the bottom
corners of (#1-A2, #2-A2) Left Side Bottom Panel and
Right Side Bottom Panels are completely flushed with
the back and front corners of (#4) Bottom Panel.
Attach (#3) Top Panel to (#1-A1) Left Side Upper Panel
and (#2-A1) Right Side Upper Panel. Make sure the
front of the panel faces downward. Line up screw holes,
use 6pcs (#41) Screw F to tighten.
ASSEMBLY INSTRUCTIONS (pg 9 of 13)
Storage Cabinet (Model No. 20143)
Repeat Step 3, use (#7-A1) Right Door - Upper Panel,
(#7-A2) Right Door - Bottom Panel, (#6-A3) Door Panel
Connection Part, use 1pc (#41) Screw F to tighten the
touching sides, use 4pcs (#41) Screw F to tighten from
the the top touching side, and 4pcs (#52) Screw K to
tighten from outside edge.
Make sure the (#7-A1) Right Door - Upper Panel is
flushed with (#7-A2) Right Door - Bottom Panel.
Insert (#7-A3) Key Rod into the bottom tab hole of
(#7-A2) Right Door - Bottom Panel, twist out the Pre-
assembled (#53) Screw L on the key rod linkage plate,
attach (#7-A3) Key Rod by lining up the screw hole and
tightening back in the (#53) Screw L.
Front
Back
Front
Back
Front
Back
Front
Back

Step 8: Install (#8, #9 and #10) Back Panels.
Step 9: Install (#12 & #13) Wheels.
Step 10: Install (#15-1, #16-1 and #17-1) Corner Protections.
Install the Wheels with Brake (#12) onto the front of
the cabinet and screw the Wheels W/O Brake (#13)
onto the back of the cabinet. Use 16pcs (#17) Screws
D to tighten.
1). Attach (#15-1, #16-1) Corner Protection A, B onto
Top of the cabinet, use 10pcs (#54) Screw N to tighten.
2). Attach (#17-1) Middle Corner Protection to the
middle of (#1-A) Left Side Panel and (#2-A) Right Side
Panel, use 8pcs (#54) Screw N to tighten.
3). Attach (#58) Bumper to the corner of (#4) Bottom
panel, use 16pcs (#16) Screw C to tighten.
ASSEMBLY INSTRUCTIONS (pg 10 of 13)
Storage Cabinet (Model No. 20143)
1). Attach (#10) Bottom Back Panel onto both Bottom
of Left and Right Side Panels (#1-A2 and #2-A2) and
Bottom Panel (#4), line up screw holes, use 7pcs (#41)
Screw F to tighten.
2). Attach both (#9) Middle Back Panel above (#10)
Bottom Back Panel the same way. Place the groove of
the (#9) Middle Back Panel onto the top edge of the
(#10) Bottom Back Panel, use 16pcs (#41) Screw F to
tighten.
3). Use 13pcs (#41) Screw F to install (#8) Upper Back
Panel the same way.

Step 11: Install (#23) Magnet.
Step 12: Install (#6-A, #7-A) Left and Right Doors.
Step 13: Install (#5) Middle Shelves.
Note: 68 kg / 150 lb maximum loading for each shelf.
ASSEMBLY INSTRUCTIONS (pg 11 of 13)
Storage Cabinet (Model No. 20143)
Place (#23) Magnet onto (#3) Top Panel and (#4)
Bottom Panel facing the front, use 4pcs (#41) Screw
F to tighten.
1). Attach (#6-A) Left Door to (#1-A) Left Side Panel,
use 11pcs (#41) Screw F to tighten.
Note: The screw holes on the door hinge have
tolerance, enabling the door to be adjusted and
centered in the door frame. Place top, middle and
bottom Screws first. Don't tighten screws
completely - this may save time by avoiding having
to make slight adjustments for leveling door panels
later.
2). Install (#7-A) Right Door the same way.
1). Decide the height for the each Middle Shelf (#5).
Place 1pc of (#34) Hook into the hook slot where
each corner of shelf should be placed. Make sure
the hooks supporting each shelf are at same height.
Note: All (#5) Middle Shelves need a hook at each
corner to support it.
2). Place each (#5) Middle Shelf into cabinet and
push down onto (#34) Hooks.

DO NOT SKIP THIS STEP (!)
Step 14: Install Mounting Strap (#60)
Stainless Steel Maintenance:
These parts have an UltraGuard® fingerprint resistant finish. Do not use
traditional stainless steel cleaners on this unit. Lightly wipe off once a
month with clean warm water and a soft cloth (preferably a microfiber
cloth). This is the safest formula to prevent new stains from appearing
over time and manage unwanted fingerprints or grease marks.
Remember to always wipe in the direction of the surface grain (NEVER
ACROSS) and always use a lint-free cloth. Once the surface is
clean,thoroughly wipe dry with a soft absorbent cloth.
ASSEMBLY INSTRUCTIONS (pg 12 of 13)
Storage Cabinet (Model No. 20143)
A. Remove 1 pc Screw F (#41) from the back corner
protection.
B. Attach the Mounting Strap (#60) to the back
Corner Protection brackets as the left photo shows
using Screw O (#61) and Washer (#27).
C. Drill a hole in the wall with a 5/16" drill bit, insert
the Wall Anchor (#55-A) into the hole.
D. Attach the other end of the Mounting Strap (#60)
to the wall using Screw M (#55) and Washer (#27-B).
Repeat steps A through D to install the other
mounting strap.

(pg 13 of 13)
Customer Service (North America):
Tel [phone] | Tel [phone] (English)
Monday through Friday 9:00 am - 4:00 pm (Pacific Time)
English: [e-mail]
Delta, BC V4G 1 L8 Canada
www.vancouverclassics.com (en anglais)
© 2019 Seville Classics, Inc.
Model No. 20204
UltraHD 6- Drawer Rolling Cabinet
Model No. 20238
UltraHD Rolling Cabinet
UltraHD Line
Model No. 16238
UltraHD Mega Cabinet
Model No. 16236
UltraHD Storage Cabinet

Model No. 20215
UltraHD Trash Bin
Model No. 20255
UltraHD Tool Box
Model No. 20262
UltraHD Rolling Workbench
UltraHD Line
Model No. 20267
UltraHD Workcenter
Model No. 20206
UltraHD Workbench
Model No. 20230
UltraHD Wall Cabinet