Sharp KI-G75EU User manual

Home Appliances
Air Purifier
For Life
KI-G75EU
Air Purifier
With Humidifying Function
Service
& Support
Visit our website:
www.sharphomeappliances.com
Or contact us:
Operation manual
EN
Instrukcja obsługi
PL
Εγχειρίδιο χρήσης
GR
Návod k obsluze
CZ
Návod na použitie
SK
Valdymo vadovas
LT
Lietošanas instrukcija
LV
Kasutamisjuhend
ET
Használati útmutató
HU
Руководство по эксплуатации
RU
“Plasmacluster” and “Device of
a cluster of grapes” are trade-
marks of Sharp Corporation.
* The number in this technology mark indicates an
approximate number of ions supplied into air of
1 cm3, which is measured around the centre of a
room applicable oor area (at 1.2m height above
the oor) when the product is placed close to a
wall at the MED mode setting.
KI-G75EU_10_languages_A.indb 1 2019-02-18 10:51:36

CONTENTS
IMPORTANT SAFETY INSTRUCTIONS ............................................................. 2
PART NAMES ...................................................................................................... 4
PREPARATION.................................................................................................... 6
OPERATION
START / STOP .................................................................................................. 7
AUTO MODE .................................................................................................... 7
CLEAN ASSIST MODE..................................................................................... 7
CLEAN ION SHOWER MODE.......................................................................... 7
PLASMACLUSTER ION SPOT MODE............................................................. 8
AIR FLOW DIRECTION SETTING ................................................................... 8
FAN SPEED SETTING ..................................................................................... 8
HUMIDIFICATION SETTING ............................................................................ 8
PRE-FILTER AUTO CLEANING ....................................................................... 9
ON TIMER ....................................................................................................... 9
OFF TIMER ...................................................................................................... 9
SELECTING DISPLAY..................................................................................... 10
CHILD LOCK.................................................................................................... 10
PLASMACLUSTER ION ON/OFF.................................................................... 10
HOW TO CHANGE VARIOUS SETTING......................................................... 10
CARE AND MAINTENANCE
CARE INDEX ................................................................................................... 12
FILTER RESET LIGHT .................................................................................... 12
WATER TANK .................................................................................................. 12
MAIN UNIT / BACK PANEL ............................................................................. 12
SENSORS........................................................................................................ 12
HUMIDIFYING FILTER / HUMIDIFYING TRAY ............................................... 13
HEPA FILTER / DEODORIZING FILTER ......................................................... 14
PLASMACLUSTER ION GENERATING UNIT ................................................ 14
DUST BOX....................................................................................................... 15
PRE-FILTER .................................................................................................... 16
REPLACEMENT
FILTERS........................................................................................................... 17
PLASMACLUSTER ION GENERATING UNIT ................................................ 17
TROUBLESHOOTING........................................................................................ 18
SPECIFICATIONS............................................................................................... 20
Thank you for purchasing this SHARP Air Purier.
Please read this manual carefully before using the product.
This manual should be kept in a safe place for handy reference.
ENGLISH
KI-G75EU_10_languages_A.indb 2 2019-02-18 10:51:36

EN-1
The air purier draws in room air through the air intake,
circulates it through a Pre-lter, a Deodorizing Filter and
a HEPA Filter inside the main unit, and then discharges
it through the air outlet. The HEPA Filter can remove
99.97% of dust particles as small as 0.3 microns that
pass through the lter and also helps absorb odours.
The Deodorizing Filter gradually absorbs odours as
they pass through the lter.
Some odours absorbed by the lters will break down
over time, causing additional odours. Depending on
usage conditions, and especially if the main unit is used in environments signicantly more
severe than a normal household, these odours may become noticeable sooner than expected. If
these odours persist, replace the lters.
NOTE
• The air purier is designed to remove air-suspended dust and the odours.
The air purier is not designed to remove harmful gases such as carbon monoxide contained in cigarette smoke.
The air purier may not completely remove an odour if the source of the odour is still present.
Please read before operating your new Air Purier
Pre-lter
(inside)
Deodorizing Filter
HEPA Filter
ENGLISH
KI-G75EU_10_languages_A.indb 1 2019-02-18 10:51:36

EN-2
IMPORTANT SAFETY INSTRUCTIONS
Always follow basic safety precautions
when using electrical appliances,
including the following:
WARNING – Always observe the following to
reduce the risk of electrical shock, re, or injury:
• Read all instructions before using the
main unit.
• Use only a 220-240 volt outlet.
• This appliance can be used by chil-
dren aged from 8 years and above and
persons with reduced physical, sen-
sory or mental capabilities or lack of
experience and knowledge if they have
been given supervision or instruction
concerning use of the appliance in a
safe way and understand the hazards
involved. Children shall not play with
the appliance. Cleaning and user main-
tenance shall not be made by children
without supervision.
• If the power cord is damaged, it must
be replaced by the manufacturer, its
service agent, a Sharp authorized
Service Centre or similarly qualied
persons in order to avoid a hazard.
Contact the nearest Service Centre for
any problems, adjustments, or repairs.
• Be sure to remove the power plug
when relling the Water Tank, before
performing maintenance, when remov-
ing and attaching and replacing the l-
ter and when not using for a long time.
Failure to do so can cause a short
circuit resulting in electrical shock or
re.
• Do not use the main unit if the power cord
or plug is damaged or if the connection to
the wall outlet is loose.
• Periodically remove dust from the plug.
• Do not insert ngers or foreign objects
into the air intake or air outlet.
• When removing the power plug, always
hold the plug and never pull on the cord.
Failure to do so can cause a short circuit
resulting in electrical shock or re.
• When removing the main unit, do not
damage the power cord with the casters.
Failure to do so can cause electric shock,
heat generation, or re.
• Be careful not to damage the power cord,
it may cause electric shock, excess heat
or res.
• Do not remove the plug when your hands
are wet.
• Do not place the main unit near or on
hot objects, such as stoves or heaters,
or where it may come into contact with
steam.
• Do not operate the main unit in rooms
where aerosol insecticides are present.
Do not operate the main unit in rooms
where there is oily residue, incense,
sparks from lit cigarettes, or chemical
fumes in the air. Do not operate the main
unit in places where it may get wet, such
as a bathroom.
• Be cautious when cleaning the main unit.
Strong corrosive cleansers can damage
the exterior.
• When carrying the main unit, rst remove
the Water Tank and Humidifying Tray, and
then hold the main unit by the handles on
both sides.
• Do not drink the water in the Humidifying
Tray or Water Tank.
• Do not expose the main unit to water. Do-
ing so can cause a short circuit or electri-
cal shock.
• Replace the water in the Water Tank daily
with fresh tap water, and regularly clean
the Water Tank and Humidifying Tray .
When the main unit is not in use, dispose
of the water in the Water Tank and Hu-
midifying Tray. Leaving water in the Wa-
ter Tank or Humidifying Tray can cause
mold, bacteria, and bad odours. In rare
cases, such bacteria can be a health haz-
ard.
NOTE – What to do if the main unit interferes
with radio or TV reception
If the air purier interferes with radio or
television reception, try one or more of the
following measures:
• Adjust or reposition the receiving
antenna.
• Increase the distance between the main
unit and the radio or TV.
• Connect the equipment into an outlet on
a circuit different from that of the radio or
TV receiver.
• Consult the dealer or a qualied radio or
TV technician.
CAUTIONS CONCERNING
KI-G75EU_10_languages_A.indb 2 2019-02-18 10:51:36

EN-3
OPERATION
• Do not block the air intake or air outlet.
• Always operate the main unit in an upright
position.
• Do not move the main unit when it is in
operation.
• When moving the main unit, use the
handles on both sides.
• If the main unit is on easily damaged
ooring, an uneven surface, or thick-piled
carpet, lift it up when moving.
• When moving the main unit by its
casters, move it slowly and in a horizontal
direction.
• Turn the main unit off and remove the
water tank before moving, take care not to
catch your ngers.
• Do not operate the main unit without
the lters, the Water Tank, and the
Humidifying Tray properly installed.
• Do not wash and reuse the HEPA lter
and the Deodorizing lter.
Doing so will not improve lter
performance and can also cause electric
shock or operating malfunctions.
• Clean the exterior with a soft cloth only.
Do not use volatile uids or detergents.
The main unit surface may be damaged
or cracked with Benzine paint thinner or
polishing powder. In addition, the sensors
may malfunction as a result.
• The frequency of descaling maintenance
will depend on the hardness of and the
impurities in the water that you use; the
harder the water the more often descaling
will be necessary.
• When relling the Water Tank, make sure
of no water leaking from the Water Tank.
• Be sure to wipe off any excess water on
the outside of the Water Tank.
• Do not use hot water (40 ºC or more),
chemical agents, aromatic substances,
dirty water, or other damaging substances.
Doing so can deform the unit or cause it
to malfunction.
• Use only fresh tap water. Using other
water sources risks the growth of molds,
fungi, or bacteria.
• Do not shake the Water Tank with holding
the carrying handle.
• Do not remove the Humidifying Filter from
the lter frame except replacing it.
• Avoid spilling water when removing or
cleaning the Humidifying Tray.
• Do not remove the Float. If it comes off,
refer to page 13.
• Do not use the detergents for
maintenance of the Humidifying Tray and
Cover. If cause deformation, tarnishing,
cracking (water leakage).
• Do not scrub the Back Panel hard during
its maintenance.
INSTALLATION GUIDELINES
• Avoid locations where the sensors are
exposed to direct wind.
Doing so can cause the main unit to
malfunction.
• Avoid locations where furniture, fabrics,
or other objects can come in contact with
the main unit and interfere with the intake
and outtake of air.
• Avoid locations where the main unit
is exposed to condensation or drastic
changes in temperature. Appropriate
room temperature is between 0 – 35 ºC.
• Place the main unit on a level and stable
surface with sufcient air circulation.
When placed on heavy carpet, the
main unit may vibrate slightly. Place the
main unit on a level surface to avoid
water leakage from the Water Tank and
Humidifying Tray.
• Avoid locations that generate grease or
oily smoke. Doing so can cause the main
unit exterior to crack and the sensors to
malfunction.
• The dust collecting ability of the main
unit is effective even when the main unit
is as close to 3 cm from the wall,the
surrounding walls and oor may get
dirty. Please place the main unit at a
distance from the wall. The wall directly
behind the air outlet may become dirty
over time. When using the main unit for
an extended period of time at the same
location, periodically clean the walls
adjacent to it.
FILTER GUIDELINES
• Follow the instructions in this manual for
proper lter care and maintenance.
ENGLISH
KI-G75EU_10_languages_A.indb 3 2019-02-18 10:51:36

PART NAMES
MAIN UNIT
7
10
8
1
4
3
5
Locked Unlocked
13
22
20
25
26
14
19
29
30
Detection range of Light sensor
Do not install the unit in the following places.
The Light Sensor may not sense correctly.
Directly under
a light  xture.
31
6
11
15
2
In shadow
9
12
16
17 18
27
23
28
24
21
EN-4
1Front Display
2Operation Panel
3Front Louver
4Air Outlet (Front)
5Main Unit
6Caster (4 Locations)
7Handle (2 Locations)
8Unit Cover
9Unit Holder
(Plasmacluster Ion Generating Unit)
10 Unit Cleaning Brush
11 Caster Stopper (Right & Left)
12 Tank Handle
13 Water Tank
14 Tank Cap
15 Humidifying Tray
16 Tray Panel
17 Float
18 Roller
19 Humidifying Filter
20 Power Cord, Plug
21 Sensor (Internal)
Temperature / Humidity
22 Air Outlet (Back)
23
Sensor Filter,
Sensor (Internal)
Dust(sensitive) / Odour
24 Back Louver(Auto)
25 HEPA Filter
26 Deodorizing Filter
27 Back Panel
28 Air Inlet
29 Pre- lter
30 Pre- lter Lock
31 Dust Box
KI-G75EU_10_languages_A.indb 4 2019-02-18 10:51:38

EN-5
OPERATION PANEL Press the button with " " to start.
H
16 15 13
12345678910
24
23
11
14 12
25
171819202122
FRONT DISPLAY
1AUTO Button, Light
2POWER ON/OFF Button
3HUMIDIFY Button, Light
(Press 3 sec.) FILTER RESET Button
4CLEAN ASSIST Button, Light
5CLEAN ION SHOWER Button, Light
6Plasmacluster Ion SPOT Button, Light
7Air fl ow direction Button
(Press 3 sec.) CHILD-LOCK Button
8FAN SPEED Button
9DISPLAY SELECT Button
(Humidity / Temperature)
10 PRE-FILTER CLEAN Button, Light
(Press 3 sec.)
DUST BOX RESET Button
11 ON/OFF TIMER Button
12 Light sensor
13 FILTER RESET Light
14 CHILD-LOCK Light
15 FAN SPEED Light
16 DUST BOX RESET Light
17 PRE-FILTER CLEAN Light
18 Timer Light
19
Odour Light
Indicates the Odour Sensor detects odours.
TURN OFF Orange Red
Clean Impure
20
Cleanliness Monitor
Indicates the air purity of the room in 5 levels with colour
changes.
Blue Orange Red
Clean Impure
21 Unit Replacement Light
22
PM2.5 Light
Indicates the Dust(sensitive) Sensor detects microscopic
dust.
TURN OFF Orange Red
Clean Impure
23
DISPLAY
• Timer Monitor
Indicates setting time or remaining time of
ON/OFF timer.
(The timer is set in hours from 1 to 12 hours)
• Temperature Monitor
Temperature 0oC to 50oC is displayed.
51oC
or more
-1oC
or less
• Humidity Monitor
Humidity 20% to 90% is displayed.
20%
or less
90%
or more
24
Humidify Light
Green Humidify ON
Off Humidify OFF
Red(Flashing) Main unit needs water
25 Plasmacluster Ion Light
H
ENGLISH
KI-G75EU_10_languages_A.indb 5 2019-02-18 10:51:39

EN-6
PREPARATION Always be sure to remove the power plug
from the wall outlet.
1. Remove the Back Panel.
2. Remove the plastic bag from the
each lter.
3. Install the lters in the correct order
as shown.
4. Install the Back Panel.
1. Remove the Water Tank.
2. Fill the Water Tank with the tap wa-
ter.
3. To prevent leaks , securely tighten
the Tank Cap.
4. Install the Water Tank.
FILTER INSTALLATION REFILLING THE WATER TANK
HEPA Filter Deodorizing Filter
Click
①
②
Back Panel
②
①
満水FULL
Click
①
②
NOTE
• When replacing the lter, making a memo of
the start of use date is recommended.
HEPA Filter
Deodorizing Filter
Tag
KI-G75EU_10_languages_A.indb 6 2019-02-18 10:51:42

EN-7
OPERATION
START/STOP
AUTO MODE
CLEAN ASSIST MODE
CLEAN ION SHOWER
MODE
START STOP
It can operate at a fan speed and humidity suitable
for the room automatically.
The auto operation will be suspended for ten min-
utes when the room has been bright and clean for 3
hours (Cleanliness Monitor is blue).
♪
♪
♪
♪♪～
NOTE
• When the main unit starts operation, the opera-
tion starts in the previous mode it was operated
in.
(Except CLEAN ASSIST / CLEAN ION SHOW-
ER / PLASMACLUSTER ION SPOT mode)
NOTE
• Front Display, Cleanliness Monitor automatical-
ly switch ON and Darker based on room bright-
ness.
(When light control is set to "Auto".
(page 10,11))
Clean the  ying dust after a vacuum cleaner is
used.
The main unit operate with the higher or the highest
fan speed for 15 minutes. (The humidifying mode is
off )
NOTE
• When the operation  nishes , the main unit will
return to the prior operation mode.
• It is not able to change the fan speed and the
louver direction during this mode.
• The Plasmacluster Ion can not be turned “OFF”.
The main unit releases Plasmacluster ions with
strong air ow and collects dusts while decreasing
static electricity for 10 minutes.
After that, the DUST sensor sensitivity is automat-
ically set to ”HIGH”and quickly detects impurities
and clean the air powerfully for 50 minutes.
NOTE
• When the operation  nishes after 60 minutes,
the main unit will return to the prior operation
mode.
• It is not able to change the fan speed and the
louver direction during this mode.
• The Plasmacluster Ion can not be turned “OFF”.
ENGLISH
KI-G75EU_10_languages_A.indb 7 2019-02-18 10:51:44

EN-8
NOTE
• When operating with Humidication ON in the
modes in the table below, the unit automatically
controls humidity by sensing temperature and
humidity. (Except MAX / MED / LOW mode.)
AUTO :
The fan speed is automatically switched depending
on the amount of impurities in the air.
POLLEN :
The DUST SENSOR sensitivity is automatically set
to "HIGH" and quickly detects impurities such as
dust and pollen and clean the air powerfully.
SLEEP :
The Main Unit will operate quietly, and the fan
speed is automatically switched depending on the
amount of impurities in the air.
The Front Display go off automatically.
(When light control is set to "Auto". (page 10,11))
FAN SPEED SETTING
PLASMACLUSTER ION
SPOT MODE
AIR FLOW DIRECTION
SETTING
♪♪♪
SWING STOP
HUMIDIFICATION SETTING
♪♪
ON OFF
Temperature
Humidity
ALL MODE
(Except MAX / MED /
LOW / SLEEP)
SLEEP
MODE
~18 ºC 65 % 65 %
18 ºC~24 ºC 60 % 65 %
24 ºC~ 55 % 60 %
Use this mode when you want to remove adhering
odour, germs, and other substances from clothes,
sofas and curtains.
The main unit operates with the higher fan speed
for 8 hours.
♪
♪
• It is able to
change the front
louver direction
during this mode.
NOTE
• Emits high-density Plasmacluster Ions only in
the forward direction.
• When the operation nishes, the main unit will
return to the prior operation mode.
• It is not able to change the fan speed during this
mode.
• The Plasmacluster Ion can not be turned “OFF”.
NOTE
• If the Swing button is pressed when the louver
is swinging,
• Do not change the angle by holding Front /Back
Louver, otherwise it may lead to failure or injury.
The swing angle of the Front Lou-
ver can be adjusted.
♪ ♪ ♪ ♪ ♪
♪♪
AUTO POLLEN SLEEP LOW MED MAX
KI-G75EU_10_languages_A.indb 8 2019-02-18 10:51:45

EN-9
ENGLISH
Periodically perform Pre-lter
auto cleaning:
The air purifying operation will be suspended every
48 hours for the cleaning of the Pre-lter (the clean-
ing lasts 8 minutes)
PRE-FILTER AUTO CLEANING
Pre-lter auto cleaning
is in operation
♪
Back
panel
Pre-lter(inside)
Flashing
ON TIMER
Select the length of time you want. The Main Unit au-
tomatically starts once the selected time is passes.
Select the length of time you want. The Main Unit auto-
matically stops once the selected time is reached.
OFF TIMER
H H H H
♪♪♪♪ ♪♪
Cancel
H
ashing
H
ashing
NOTE
• If there is no operation in 3 seconds, the setting
will be nished with a beep. The Timer light will
be on and display the remaining hour before the
operation starts.
• You may reset the timer by pressing the ON/
OFF Timer button again.
(with the Main Unit ON)(with the Main Unit OFF)
H H H H
♪♪♪♪ ♪♪
Cancel
NOTE
• If there is no operation in 3 seconds, the setting
will be nished with a beep. The Display will be
back to its previous status.
• After the setting is done, press once the ON/OFF
Timer button, the remaining hour of the operation will
show, and press twice, you may reset the Timer.
Manual cleaning of
the Pre-lter:
Pre-lter auto
cleaning opera-
tion starts.
NOTE 1
NOTE 2
The auto cleaning will not start when
 The main unit is on Clean assist / Clean ion
shower / Plasmacluster ion spot mode.
 The Cleanliness Monitor is not blue.
 The room is [dark].
It is also possible to cancel periodic operation
of Pre-lter auto cleaning. (page 10,11)
If the auto cleaning is cancelled, the unit will
clean the Pre-lter and collect the dust auto-
matically every about 720 hours.
(30 days × 24 hours =720 hours)
How to stop operation of
Pre-lter auto cleaning:
It will turn off after a while.
♪♪
(During auto cleaning)
Operating
time
about 720 hours about 720 hours
The last Auto Cleaning
Auto Cleaning Auto Cleaning
Operating
time
Auto Cleaning
(about 5 minutes)
about 48 hours
Auto Cleaning
(about 5 minutes)
about 48 hours
The last Auto Cleaning
KI-G75EU_10_languages_A.indb 9 2019-02-18 10:51:48

EN-10
1. (with the Main Unit OFF)
2. Select "Function number".
Forward Reverse
or
Set
3. Select "Setting number".
Forward Reverse
or
Set
4. Press Power ON/OFF Button to
 nish the setting mode.
HOW TO CHANGE VARIOUS
SETTINGS
You can change the functions in the table "Type
of setting".
♪♪
･･･
Turn off
NOTE
• When the Plasmacluster function is
ON, the Plasmacluster Ion light on
the Front Display is on.
CHILD LOCK
PLASMACLUSTER ION
ON/OFF
The operation panel will be locked.
ON OFF
more 3 sec.
♪
more 3 sec.
♪♪
ON CANCEL
more 3 sec.
♪
♪
♪～
♪～
more 3 sec.
♪
more 3 sec.
♪♪
SELECTING DISPLAY
♪
♪♪
Humidity Temperature
(with the Main Unit ON or OFF)
♪♪
KI-G75EU_10_languages_A.indb 10 2019-02-18 10:51:50

EN-11
ENGLISH
HOW TO CHANGE VARIOUS
SETTINGS
Type of setting
Function Setting
Light Control
You can select the brightness of the Front Display.
Auto (default)
Light automatically switches based on room brightness.
Room bright-
ness
Front Display
ALL MODE
(Except SLEEP) SLEEP MODE
Bright Brighter Darker
Dark Darker Turn off
Darker
Turn off
When set to “Turn off”, the “Darker” light illuminates for 3
seconds after operation starts and then the light turns off.
The Humidify Light ashes darker only when the main unit
needs water.
The Unit Replacing Light ashes darker only when the
Plasmacuster ion generating unit need to be replaced.
Water-lling Indicator
You can set the Main Unit to make a beeping sound
when the Water Tank is empty.
CANCEL (default)
ON
The Humidify light ashes with a sound of beep which
lasts for 10 seconds.
When SLEEP Mode is set on, once the Light Sensor de-
tects that it is dark in the room, it will not beep.
Auto Restart
If the Main Unit is unplugged or if there is a power
failure, the Main Unit will resume operation with the
previous settings after power is restored.
CANCEL(default)
ON
Adjusting Sensor Sensitivity (F4-F6)
Light Sensor Low
Dust(sensitive) Sensor
Standard (default)
Odour Sensor High
Pre-lter auto cleaning function
Pre-lter auto cleaning function can be set.
ON(default)
The dust on the Pre-lter will be cleaned every 48 hours.
CANCEL
No auto cleaning for the Pre-lter.
In order to keep the air clean, the unit will clean the Pre-l-
ter and collect the dust automatically one month
(about 720 hours) after previous cleaning.
KI-G75EU_10_languages_A.indb 11 2019-02-18 10:51:52

EN-12
Clean the inside of
the Water Tank with a
soft sponge and the
Tank Cap with a cotton
swab or toothbrush.
WATER TANK
MAIN UNIT/BACK PANEL
SENSORS
CARE INDEX
FILTER RESET LIGHT
CARE AND MAINTENANCE
1
4
5
2
3
8
6
7
4
Place Page
1Water Tank 12
2Humidifying Filter / Humidifying Tray 13
3Sensors 12
4Main Unit / Back Panel 12
5HEPA Filter / Deodorizing Filter 14
6Plasmacluster Ion Generating Unit 14
7Pre- lter 16
8Dust Box 15
1. Remove the Back Panel.
2. Remove the Sensor  lter.
3. If the Sensor  lter is very
dirty, wash it with water
and dry it thoroughly.
How to clean hard to remove dirt.
How to clean hard to remove dirt.
Tank Cap Toothbrush
Rinse the inside
with water.
Wipe with a dry,
soft cloth.
Remove the dust gently with a cleaning
tool such as a vacuum cleaner.
Sensors
Sensor  lter
NOTE
NOTE
The Filter reset light will turn on after approximately
720 hours operating.
(30 days × 24 hours =720 hours)
This is a reminder to perform the maintenance de-
scribed Humidifying Filter and Tray.
After performing maintenance, reset the Filter reset
light.
RESET
more 3 sec.
♪
KI-G75EU_10_languages_A.indb 12 2019-02-18 10:51:54

EN-13
ENGLISH
HUMIDIFYING FILTER / HUMIDIFYING TRAY
How to clean hard to remove dirt.
Rinse with plenty of water.
How to remove
the Humidifying
Filter and Tray.
How to attach the Humidifying
Filter and Tray.
After maintenance, correctly reattach
the parts.
NOTE
①
②
①
②
Float
Tray Panel
Roller
• Do not remove the Float, the Tray Panel
and the Rollers. If they come off, refer to
below.
Kitchen detergent
(only Humidifying tray)
Citric acid
(available at some drugstores)
100% bottled lemon juice
with no pulp
1
1. Fill the tray half-way with
water.
2. Add a small amount of
kitchen detergent.
2 1/2 cups of water
3 teaspoons
3 cups of water
1/4 cup
2
Soak for 30
minutes.
Soak for 30 minutes.
(When using lemon juice as your
descaling solution, allow for more
soak time.)
3Rinse off the kitchen detergent or the descaling solution with clean water.
How to install the Float, the Tray Panel and thr Roller
Tray Panel
Roller
Float
1. Insert the Float un-
der this tab.
3. Insert the tab on
the other side of the
oat into the hole.
Tab
Float
Cross-Section view
2. Insert the tab of the
oat into the hole.
Click
Click
Click
KI-G75EU_10_languages_A.indb 13 2019-02-18 10:51:56

EN-14
Remove the dust on the HEPA Filter and
Deodorizing Filter.
CAUTION
Do not wash the lters. Do not expose to sunlight.
(Otherwise these lters may lose efcacy.)
HEPA FILTER
Clean only the tagged surface. Do not clean up the oppo-
site surface. The lter is fragile, so be careful not to give
too much pressure.
Deodorizing Filter
Both surfaces can be cleaned. The lter may be broken
if being too much pressure is applied on it, so please han-
dle it with care.
Some odours absorbed by the lters will break down over
time, causing additional odours. Depending on usage
conditions, and especially if the Main Unit is used in envi-
ronments signicantly more severe than a normal house-
hold, these odours may become noticeable sooner than
expected.
Replace the lter in those cases or if dust is unable to be
removed after maintenance.
HEPA FILTER / DE-
ODORIZING FILTER
PLASMACLUSTER ION
GENERATING UNIT
(Electrode section)
Tag
1. Remove the unit cover, and pull out
the unit holder.
2. Remove dusts from the electrode
section.
3. Insert the unit holder in the Main Unit,
and install the unit cover.
CAUTION
• Do not clean with anything other than the unit cleaning
brush. Doing so could lead to failures in the unit.
• Do not touch the electrodes directly. Doing so could
lead to injury.
• Do not transform the electrode section. Doing so can
damage it.
• Do not touch the connection terminals. Doing so can
damage them.
Unit Cleaning Brush
Electrode(4 places)
After cleaning
Electrode(needle)
Around the base
Click
Connection terminals
KI-G75EU_10_languages_A.indb 14 2019-02-18 10:51:58

EN-15
ENGLISH
DUST BOX
DUST BOX RESET LIGHT
When the Dust box reset
light will turn on, please
remove the dust in the
Dust Box.
1. Remove the Dust Box.
2. Remove the cover of Dust Box.
3. Remove the brush.
4. Remove the dust
in the Dust Box.
5. Attach the brush in the Dust Box.
Cover
Brush
Wash with water.
• Dry them thoroughly.
How to clean hard to remove dirt.NOTE
①
②①
②
③
Push
①
①
②
6. Attach the cover in the Dust box.
7. Install the Dust Box.
8. Reset the Dust box reset Light.
①
②
Brush
Cover
Dust Box
Comb
How to remove the comb.
How to attach the comb.
more 3 sec.
♪
KI-G75EU_10_languages_A.indb 15 2019-02-18 10:52:00

EN-16
1. Remove the Pre- lter Lock.
2. Remove the Shaft (upper).
Rotate the Shaft (upper) until the protrusion is
visible, then remove the protrusion.
3. Pull out the Pre- lter from the Shaft
(upper).
4. Pull out the
Pre- lter from
the Shaft (lower).
5. Soaking and cleaning the Pre- lter.
1. Add a small amount of kitchen detergent to
water and soak for about 10 minutes.
2. Rinse off the kitchen de-
tergent with clean water.
3. Dry it thoroughly.
PRE-FILTER
②
①
6. Insert the Pre- lter shaft into the
groove of the Shaft (upper).
7. Attach the Shaft (upper) on the Back
Panel.
Insert the left part of the Shaft (upper) into the
Back Panel ( ) and install it ( ).
8. Roll up the Pre- lter.
9. Pull down the Pre- lter shaft and
insert it into the groove of the Shaft
(lower).
10. Attach the Pre- lter Lock.
①
②
Shaft (upper) Protrusion
Shaft (upper)
Pre- lter
Pre- lter
Shaft (lower)
Pre- lter
Shaft (upper)
Pre- lter shaft
①②
Shaft (upper)
Insert protrusion
Click, Click, ...
Pre- lter shaft
Pre- lter shaft
Shaft (lower)
CAUTION
• Do not clean it too hard. Do not wash it with
a washing machine.(Otherwise it might cause
damage.)
• Do not dry it with a dryer. (Otherwise it might
cause shrinkage.)
Pre- lter Lock
①②
KI-G75EU_10_languages_A.indb 16 2019-02-18 10:52:03

EN-17
ENGLISH
REPLACEMENT
FILTERS PLASMACLUSTER ION
GENERATING UNIT
LIFE OF FILTERS
Filter life varies depending on the room environment,
usage conditions, and location of the Main Unit.
Lifespan of HEPA lter and Deodorizing lter and re-
placement suggestions are based on purifying a room
in which 5 cigarettes are smoked per day and the Main
Unit's dust collection and deodorizing performance has
declined to half the level of a new lter.
We recommend replacing the lter more frequently if
the Main Unit is used in conditions signicantly more
severe (PM2.5 etc.,) than a normal household.
 HEPA Filter : About 10 years after opening
 Deodorizing Filter : About 10 years after opening
 Humidifying Filter : About 10 years after opening
Replacement Filter Model
Consult your dealer when purchasing a replace-
ment lter.
HEPA Filter (1 unit)
FZ-G75HFE
Deodorizing Filter (1 unit)
FZ-G60DFE
Humidifying Filter (1 unit)
FZ-AX6MFE
* Do not dispose the
Filter Frame.
Disposing of lters
Dispose of used lters according to local laws and
regulations.
HEPA Filter material:
• Polypropylene • Polyethylene
Deodorizing Filter material:
• Paper • ABS resin
Humidifying Filter material:
• PET • Rayon
UNIT REPLACEMENT LIGHT
When the total operation time exceeds 17,500
hours, the Unit replacement light will ash to indi-
cate that the Plasmacluster Ion Generating Unit
needs replacement.
Operating time
17,500 hours
Flash slowly
Replace the Plasmacluster
Ion Generating Unit
19,000 hours
Flash quickly
No Plasmacluster ions will
be released by the Plasma-
cluster Ion Generating Unit.
* The replacement time is not related to the selected
operation mode.
Replacement Plasmacluster Ion
Generating Unit Model
Consult your dealer when purchasing a replace-
ment Plasmacluster Ion Generating Unit.
IZ-C75SE
② ①
① ②
Disposing of Plasmacluster Ion
Generating Unit
Dispose of used Plasmacluster Ion Generating Unit
according to local laws and regulations.
material:
• Polybutylene Terephthalate
• electronic parts
Remove the claw of
unit holder ( ), and
remove the Plasma-
cluster Ion Generat-
ing Unit( ).
Filter
Frame
Humidify-
ing Filter
KI-G75EU_10_languages_A.indb 17 2019-02-18 10:52:04

EN-18
TROUBLESHOOTING
Odour and smoke persists.
• Check the lters. If they appear to be extremely
dirty, clean or replace them.
The Cleanliness Monitor is blue
even when the air is not clean.
• The air may have been dirty when the main unit
was plugged in. Unplug the main unit, wait one
minute, and then plug the main unit in again.
The Cleanliness Monitor light is red
even when the air is clean.
• Dirty or clogged dust(sensitive) sensor openings
interfere with sensor operation. Gently clean the
sensor lter or the back panel.
The Main Unit makes a clicking or
ticking sound.
• The main unit may make clicking or ticking sounds
when it is generating ions.
• Operating sound is generated when the Main unit
is on Pre-lter Auto Cleaning mode.
Air discharged from the Main Unit
has an odour.
• Check to see if the lters are extremely dirty.
• Clean or replace the lters.
• Use only fresh tap water. Using other water sources
risks the growth of mold, fungi, or bacteria.
The Main Unit does not operate
when cigarette smoke is in the air.
• Make sure the Main Unit is installed in a location
in which the sensors can detect cigarette smoke.
• Check to see if the dust(sensitive) sensor
openings are blocked or clogged. If they are
blocked or clogged, clean the sensor lter or the
back panel.
The FILTER RESET Light is on.
• Whenever after performing maintenance or
replacing the Humidifying lter, connect the power
cord to an outlet and then press the Filter Reset
Button.(page 12)
The Front Display is turned off.
• When Light control is set to "Turn off", the light is
always off. If you do not want the light to be off, set
Light control to "Auto" or "Darker" setting.
(page 10,11)
The Humidify Light on the Front
Display does not light up when the
tank is empty.
• The room has reached the appropriate level of
humidity and has stopped humidifying.
• Check the styrofoam oat for impurities. Clean the
Humidifying Tray. Make sure that the unit is on a
level surface.
The water level in the tank does
not decrease or decreases slowly.
• Check to see if the Humidifying Tray and
Water Tank are correctly installed. Check the
Humidifying Filter.
• If the lter is extremely dirty, clean or replace it.
The Cleanliness Monitor changes
colour frequently.
• The Cleanliness Monitor automatically changes
colour when the dust(sensitive) sensor and odour
sensor detect impurities. If you are concerned
about the change, you can change sensor
sensitivity.(page 10,11)
The Front display does not match
weather report or another hygrometer
or thermometer in the room.
• Outdoor and indoor as well as the home envi-
ronment (the volume of trafc nearby, number of
stories in home, etc.) may cause a reading differ-
ent than those data.
• There is a difference in the level within the same
room.
The operation stops suddenly and
there is no air from the air outlet.
• Is the Main unit on Pre-lter Auto Cleaning mode?
The operation stops when the Main unit is on
Pre-lter Auto Cleaning mode (it lasts about 8
minutes).
The Pre-lter Auto Cleaning starts
even after it has been set OFF
(cancelled).
• The Pre-lter Auto Cleaning will start anyway after
720 hours’ operation to prevent the Pre-lter from
being blocked by dusts.
KI-G75EU_10_languages_A.indb 18 2019-02-18 10:52:04