Sharp FU-28H-A User manual

中文
FU-28H-A
AIR PURIFIER
INSTALLATION MANUAL
OPERATION MANUAL
R
*Plasmacluster is a trademark of
Sharp Corporation.
ENGLISH
空氣清新機
安裝說明書
使用說明書
Wall-mounting type
壁掛型
* Plasmacluster 是聲寶公司的商標。

ENGLISH
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS .... E-2
•WARNING ....................................................E-2
•CAUTIONS CONCERNING OPERATION ...E-2
•REMOTE CONTROL LIMITATIONS ............E-3
•CAUTIONS WHEN MOUNTING
THIS PRODUCT TO A WALL .......................E-3
•FILTER GUIDELINES .................................. E-3
PART NAMES .......................................... E-4
•MAIN UNIT DISPLAY ................................... E-4
• BACK ...........................................................E-4
• ACCESSORIES ...........................................E-4
PREPARATION........................................ E-5
•INSERTING BATTERIES
IN THE REMOTE CONTROL ......................E-5
•REMOTE CONTROL USE ...........................E-5
INSTALLATION ....................................... E-6
FILTER INSTALLATION ........................ E-10
OPERATION .......................................... E-12
•MAIN UNIT OPERATION .......................... E-12
•REMOTE CONTROL OPERATION .......... E-13
CARE AND MAINTENANCE ................. E-14
•FILTER REPLACEMENT
GUIDELINES ............................................ E-14
•MAIN UNIT ................................................ E-15
•ODOUR SENSOR .................................... E-15
• PRE-FILTER ............................................. E-15
SPECIFICATIONS ................................. E-15
TROUBLE SHOOTING .......................... E-16
E-1
ENGLISH
Thank you for purchasing the SHARP FU-28H-A.
Please read this manual carefully for the correct
usage information. Before using this product, be
sure to read the section: “Important Safety Instruc-
tions.”
After reading this manual, retain it in a convenient
location for future reference.
HOW SHARP AIR PURIFIER WORKS
An air purifier draws in room air from
its air intake, lets the air pass through
an Active Carbon Filter (Deodorizing
Filter) and a HEPA Filter (dust collec-
tion filter) inside the unit, then dis-
charges the air from its air outlet. The
air purifier repeats this process by
moving its internal fan.
As air passes through, the HEPA
Filter can remove dust particles. The
Active Carbon Filter gradually absorbs
odour elements as they repeatedly
pass through the filter.
(Odour elements are absorbed by
HEPA Filter as well.)
Some odour ingredients absorbed by
the filters may become separated and
may be discharged through the air
outlet and result in additional odour.
Depending on the usage environ-
ment, this odour may become strong
in a shorter period than expected.
In this case, purchase the optional
replacement filter kit FZ-28SEF.
NOTE
The air purifier is designed to remove
air-suspended dust and odour, but not
harmful gases (for example, carbon
monoxide contained in cigarette
smoke). Neither can it completely
remove odours that are always
present (for example, odours from
construction materials and pet
odours).
HEPA Filter
Active Carbon Filter

IMPORTANT SAFETY INSTRUCTIONS
E-2
When using electrical appliances, basic safety precautions should be followed, including the
following:
WARNING - To reduce the risk of electrical shock, fire or injury to persons:
•Read all instructions before using the air purifier.
•Use only a 220 volt outlet .
•Do not use the air purifier if the power cord or plug is damaged or the connection to the wall
outlet is loose.
•Periodically remove dust from the power plug.
•Do not insert fingers or foreign objects into the intake or air outlet.
When removing the power plug, always hold the plug and never pull the cord.
Electrical shock and/or fire from short circuit may occur as result.
•Do not use this air purifier near gas appliances or fireplaces.
•Remove the power plug from the wall outlet before cleaning the unit and when not using the
unit.
Electrical shock from bad insulation and / or fire from short circuit may occur as a result.
•If the power cord is damaged, it must be replaced by the manufacturer, its service agent, Sharp
authorized service or similarly qualified person in order to avoid a hazard.
•Do not operate when using aerosol insecticides or in rooms where there is oily residue, incense,
sparks from lit cigarettes, chemical fumes in the air or a humidity condition.
•Use care when cleaning the air purifier. Strong corrosive cleansers may damage the exterior.
•Only Sharp Authorized Servicers should service this air purifier. Contact the nearest Servicer for any
problems, adjustments, or repairs.
•The batteries must be removed from the remote control before disposal, and the batteries must be
disposed safely.
CAUTIONS CONCERNING OPERATION
• Do not block the intake and air outlet.
•Do not use the unit near or on hot objects, such as range or where it may come into contact with
steam.
•Always hold the main unit when moving it.
Holding the front panel when carrying may cause it to detach, thus dropping the unit and resulting in
bodily injury.
•Do not operate the unit without the filter.
•Do not wash the Active Carbon Filter and the HEPA Filter.
Not only it does not improve filter performance, it may cause electric shock or malfunction.
•Clean the exterior with a soft cloth only.
The unit surface may be damaged or cracked.
In addition, the sensor may malfunction as a result.

ENGLISH
REMOTE CONTROL LIMITATIONS
DO NOT USE THE REMOTE CONTROL IN THE FOLLOWING LOCATIONS:
•Any location where there is inverter lighting equipment or electronic spontaneous lighting
equipment
The remote control may become inoperative. In this case, move away from such lighting equipment or
change direction.
•Location exposed to direct sunlight or fluorescent.
The unit may not receive signals from the remote control.
CAUTIONS WHEN MOUNTING THIS PRODUCT ON A WALL
•Avoid a location where the sensor is exposed to direct wind.
The unit may not operate properly.
•Avoid a location where curtains, etc., come into contact with the intake or air outlet.
Curtains, etc., may become dirty or a malfunction may occur.
•Avoid locations where the unit is exposed to condensation, due to drastic temperature changes.
•Place on a stable surface with sufficient air circulation.
• Install the unit on a wall, wooden pillar, crosspiece, etc. that is flat and strong enough.
•Do not install the unit on a thin wall or on plasterboard. The unit may fall down if installed on an
insufficiently strong wall.
•To install the unit on a wooden wall that is less than 10 mm thick, consult your dealer and have
them confirm the strength of the wall before installation.
•Always hold the main unit when moving it.
Holding the front panel may cause it to become detached, thus dropping the unit and resulting in
bodily injury.
• Do not install when there is generation of lampblack, such as in a kitchen, etc.
The unit surface may crack or the sensor may malfunction as a result.
FILTER GUIDELINES
•Follow the instructions in this manual for correct care and maintenance of the filters.
E-3

PART NAMES
MAIN UNIT DISPLAY
E-4
Plasmacluster Indicator Light
Fan Speed Indicator Lights
OFF Timer Display Indicator Lights
Remote Control Receiver
Power ON/OFF button
Fan Control button
OFF Timer button
Odour Sensor
Filter Frame
HEPA Filter (white)
(with Microbial Control Filter)(blue)
Active Carbon Filter
(Deodorizing Filter)
Stainless Steel Pre-Filter
Front Panel
BACK
Power Cord
Adjusting Guide
Power Cord
Power Plug
ACCESSORIES
Remote Control
(1 unit)
Battery
(AA battery x 2 )
Operation Manual
Wall mounting kit
•Wall mounting bracket
•Wood screws (4 pcs)
•Fisher plugs (4 pcs)
Air Outlet
(Shape of plug
depends on country)

ENGLISH
E-5
About the batteries
•The battery life is about 1 year.
•Replace the batteries when the remote control becomes inoperative.
•Incorrect usage of the batteries may cause battery fluid leakage and/or
damage. Take care of the following when handling:
•When replacing the batteries, replace both batteries with new ones of the
same type. (Use 2 AA manganese batteries .)
•When not using the unit or remote control for an extended period, remove the
batteries. This prevents malfunction of the remote control from battery fluid
leakage.
•The batteries of the accessory are for initial use only and may be depleted
within 1 year.
INSERTING BATTERIES IN THE REMOTE CONTROL
1Remove the back cover
Press and slide the back cover to remove.
2Insert batteries
Insert batteries with and as shown
below.
3Close the back cover
PREPARATION
−
−
＋
＋
REMOTE CONTROL USE
•Operate the remote control facing the main unit receiver.
•The signal range is about 7m (front).
• Make sure there are no objects blocking the path of the signal.
•Abeep sound will be heard from the main unit when a signal is received.
NOTE
•Avoid dropping or damaging the remote control,
using in a high humidity condition, in direct sun-
light or near a heat source.
Receiver
Transmitter

FOR APPROPRIATE INSTALLATION
To remove room odour
Installing the unit high up on the wall is most effective.
To remove room dust
Comparatively large dust particles such as pollen and house dust collect in the lower strata of the
room air.
Select a location in the room where the air circulation is good.
This improves the cleaning performance and causes Plasmacluster ions to spread throughout the
room.
Operating Conditions
Please operate the unit under the following conditions.
It is recommended to use the unit in a room where the temperature is in the range of 0 - 35C°.
Avoid locations where the unit is exposed to condensation, due to drastic temperature changes.
INSTALLATION
E-6
Installation Cautions
•Before fixing the wall mounting bracket, make sure there is nothing that could obstruct installation of the unit.
Then fix the wall mounting bracket through screw holes with the supplied wood screws.
•Install the unit on a wall, wooden pillar, crosspiece or the like that is flat and strong enough..
•If the wall is weak or made of concrete, have the unit installed by a specialist such as an electric appliance
store.
•Avoid locations near inverter lamps or where the unit is exposed to direct sunlight.
1
Determine the mounting location
Leave space around the bracket referring to the drawing below. The unit cannot
be mounted if there is insufficient spacing around the bracket.
207mm
337mm (Size of main unit)
48mm54mm235mm
482mm ( Size of main unit)
Power cord
330mm
16mm
60mm
3mm
92mm
Wall mounting bracket
Screw Holes
Screw Holes
Size of main unit
70cm or more from
side wall
70cm or more from
side wall
Center line of Wall mounting bracket
Center line of main unit
Center line of
main unit
45cm or more from the ceiling
In case you prefer free
standing installation, optional
stand FZ-FC1TS is available.
Free Standing Installation.

ENGLISH
2
Mount wall mounting bracket
•Mount the bracket using the included wood screws so that it is mounted in horizontal
balanced level.
Installation on a concrete, block or mortar surface
Drill holes of at least 35 mm depth and 5 mm diameter into the wall, drive in
fisher plugs, and fix the unit with wood screws.
Installation on a wooden pillar, crosspiece or other wooden surface
Use wood screws for installation.
E-7
Install on a
wooden pillar
φ5m
m
35mm
Install on a wooden
crosspiece
Wood screws (4)
Wooden pillar
Caution
•To install the unit on a wooden wall that is less than 10 mm thick, consult your
dealer and have them confirm the strength of the wall before installation.
•Install the unit on a wall, wooden pillar, crosspiece, etc. that is flat and strong
enough.
•Make sure that the unit is installed in an upright position, without leaning to
the right or left.
Wooden crosspiece
Wall mounting bracket
Hole on the wall
Fisher plug
Wood screw

3
Install the unit on the wall.
1Place the unit facing
up, remove the Front
Panel and Filter Frame.
2Adjust the length of the power cord.
1Measure the distance between the unit and the wall outlet.
(Refer to E-6)
2Place the unit face down, and insert the
power cord into the power cord adjust-
ing guide so as to adjust it to the meas-
ured length.
Before starting the wall installation, be sure to remove the front panel
and filter frame.
E-8
INSTALLATION
In case the power plug to
be lead to the left of the
unit.
Do not wire the
power cord right
below the wall
mounting bracket.
Power cord adjusting guide
In case the power plug to be lead
to the right of the unit.
Cautions
•To avoid scratching or damaging the unit, place it on a soft piece of cloth
until it is installed on the wall.
•Do not lead the power cord together with other cord and do not twist it.
•Never modify the power cord.
•Take care not to damage the power cord.
Front Panel Filter Frame
Air Outlet
1
2
Power Cord
Adjusting Guide

ENGLISH
E-9
3Apply a mark (tape, etc.) 8 cm above both ends of the wall mounting
bracket.
4Lift up the unit so that the hooking holes on the unit are aligned with
the marks, hook the unit onto the wall mounting bracket and slide it
to the right.
When positioned correctly, the unit will move down slightly until it
engages.
Alignment with the right hooking holes
Alignment with the left hooking holes
5Double-check the installation.
Make sure that the claws of the unit are hooked in properly. If they are
not, the unit will move sideways. In addition, the unit may fall off the
wall and be damaged.
•Make sure that the power cord is not caught in the unit.
6Remove the mark.
Wall mounting bracket
HOW TO REMOVE THE UNIT
Pull the power plug out of the wall outlet and remove
the Front Panel and Filter Frame. Holding the unit by
its lower corners, lift it up slightly, then slide it to the
right or left and lift it off toward the top.
1
2
2
2
1
mark
about 8 cm
claw socket
about 8 cm
mark
claw socket

Be sure to remove the filters from the
plastic bags before using the unit.
1Remove the Pre-Filter,
Active Carbon Filter and
HEPA Filter from the Filter
Frame.
2Remove the Active Carbon
Filter and HEPA Filter from
the plastic bags.
3Place the HEPA Filter
within the Filter Frame.
Do not install the filter backwards
or the unit will not operate properly.
4Place the Active Carbon
Filter within the Filter
Frame on top of the HEPA
Filter.
The Active Carbon Filter does not
have a front and a back.
5Next, place the Pre-Filter
within the Filter Frame.
Fit the 4 tabs of the Pre-Filter into
the holes in the Filter Frame.
E-10
FILTER INSTALLATION
Tabs
Pre-Filter
Active Carbon Filter
HEPA Filter
Filter Frame
HEPA Filter
Filter Frame
Pre-Filter
Active Carbon Filter
HEPA Filter
Filter Frame
Tabs
How to Remove the Stainless
Steel Pre-Filter
Active Carbon Filter
HEPA Filter

ENGLISH
E-11
6Mount the Filter Frame to
the main unit.
7Fill in the usage start date
on the Date Label.
Use the date as a guide for the
Filter Replacement schedule.
8Mount the Front Panel to
the main unit.
9Insert the power plug into
the wall outlet and check
on/off operation using
the remote control.
Date Label
Claw socket
Claw
Filter Frame
Front Panel

OPERATION
MAIN UNIT OPERATION
POWER ON/OFF button
•Used to start AUTO operation (short beep)
and stop operation (long beep).
•Plasmacluster Indicator Light and Fan Speed
Indicator Light (AUTO) turn on/off.
•Unless unplug the power cord, the operation
starts in the previous mode the unit was
operated in.
Fan Control button
The fan speed can be switched among Silent,
Max and AUTO.
OFF Timer button
•The set timer switches every time the button
is pressed as shown below.
•When “4 hours” is selected “4 H” indicator light
activates. When the remaining time becomes
1 hour, then indicator light switches to “1 H”.
E-12
For the first 30 seconds after the plug is inserted into the
wall outlet, the unit will check the conditions of the air.
Silent Max
AUTO
1 hour 4 hours
Cancel
•Auto Operation
Odour sensor checks the amount of impurities in the air and the fan
speed switches automatically.
•Manual Operation
Regardless of the amount of impurities, desired fan speed can be
switched between Silent and Max.

ENGLISH
E-13
POWER ON/OFF button
•Used to start AUTO operation (short beep) and
stop operation (long beep).
•Plasmacluster Indicator Light, and Fan Speed
Indicator Light (AUTO) turn on/off.
•Unless unplug the power cord, the operation
starts in the previous mode the unit was
operated in.
AUTO (Fan Speed) button
The fan speed switches automatically depending
on the amount of impurities in the air.
MANUAL (Fan Speed) button
The fan speed can be switched between Silent,
Max.
OFF Timer button
•The set timer switches every time the button is
pressed as shown below.
•When “4 hours” is selected “4 H” indicator light
activates. When the remaining time becomes 1
hour, then indicator light switches to “1 H”.
REMOTE CONTROL OPERATION
Silent Max
1 hour 4 hours
Cancel
Plasmacluster Ion Operation
While the product is in operation, the unit will constantly discharge approximately
the same amount of Positive and Negative cluster ions. This is effective for inactivating
airborne mold, viruses, bacteria, allergens and reducing mold odors.

E-14
CARE AND MAINTENANCE
To maintain optimum performance of this air purifier, please clean the unit including the
sensor and filters periodically.
When cleaning the unit, be sure to unplug the power cord, and never handle the plug
with wet hands. Electrical shock and/or bodily injury may occur as a result.
FILTER REPLACEMENT GUIDELINES
Depending on the usage environment, air outlet odour may become strong
after several months.
If dust or odours cannot be removed easily, replace the filters.
(Refer to HOW SHARP AIR PURIFIER WORKS E-1)
Guide for filter replacement timing
•The following filter life and replacement period is based on the condition of smoking 10
cigarettes per day, reducing the dust collection/deodorization power to half compared with
that of new filters.
•HEPA Filter About 12 months after opening
•Active Carbon Filter About 12 months after opening
REPLACING THE FILTERS
1See page E-10,11 for directions
on how to install the filters when
replacing.
2Fill in the usage start date of the
filters on the Date Label.
Replacement Filters
Model: FZ-28SEF
•HEPA Filter
(with Microbial Corbon Filter) : 1 unit
•Active Carbon Filter: 1 unit
Please ask for replacement filters at
your dealer of purchase.
Disposal of Filters
Please dispose of replaced filters according
to the local disposal laws and regulations.
HEPA Filter materials:
•Filter: Polypropylene
•Frame: Polyester
• Microbial Control Filter: Polypropylene, polyethylene
Active Carbon Filter Materials:
•Deodorizer: Activated charcoal
•Frame: Paper
•Net: Polypropylene 60% Polyester 40%
Pre-Filter Front Panel
Active Carbon Filter
HEPA Filter
(with Microbial Control Filter)
Filter Frame
Main Unit
Date Label
Washable Not Washable

ENGLISH
E-15
MAIN UNIT
To prevent dirt or stains on the main unit, clean as often as necessary. If stains are allowed to
remain, they may become hard to clean.
Wipe with a dry, soft cloth
For stubborn stains or dirt, use a soft cloth dampened with warm water.
Do not use volatile fluids
Benzene, paint thinner, polishing powder, etc., may damage the surface.
Do not use detergents
Detergent ingredients may damage the unit.
Keep the unit away from water
ODOUR
SENSOR
Remove dust from the sur-
faces of the sensor open-
ings with a vacuum cleaner.
Odour
Sensor
PRE-FILTER
Remove the Filter Frame, Clean the top surface of the
Pre-Filter lightly with a vacuum cleaner.
If it is contaminated heavily, remove it from the Filter Frame
to wash it.
NOTE
•In case of washing, use a soft
brush etc. and cold/warm water.
•Metal brushes or scrub brushes
may cause damage.
•After washing, leave it in the
shade until it gets dried. Then
place it back to the Filter Frame.
SPECIFICATIONS
* The applicable floor surface area is the surface area for when operating the unit in MAX fan level.
Applicable floor surface area indicates the space where a certain amount of dust pollution can be
removed in 30 minutes.
Pre-Filter
About the reduction of standby power
In order to operate the electrical circuits while the power plug is inserted in the wall outlet, this
product consumes about 1.0W of standby power.
For the conservation of energy, remove the power plug when not using the unit.
Fan Speed
Operation
~21 m
2
2.5m
MAX
29 W
168m
3
/hour
SILENT
3.1 W
30m
3
/hour
482mm(W)x142mm(D)x337mm(H)
482mm(W)x228mm(D)x373mm(H) (Stand installation)
6.2kg
Weight
Model
Power Supply
Fan Speed Adjustment
Rated Power
Air Flow Volume
Applicable Floor Surface
Cord Length
FU-28H-A
220V 50Hz
Dimensions

TROUBLESHOOTING
Before calling for repair, please review the list below, since the problem may not be a unit malfunction.
SYMPTOM REMEDY (not a malfunction)
The Remote Control does not
work
•Have the batteries been depleted?
• Are the batteries inserted correctly?
•Is a fluorescent lighting in the room flickering due to serv-
ice life? (Refer to E-5)
Odours and smoke are not re-
moved
•Replace the filters if they appear to be heavily soiled.
(Refer to E-14)
A ticking sound is heard from
the unit
•Ticking sound is emitted when the unit is generating ions.
This is normal and not a malfunction.
The discharged air has an
aroma or odour.
•Check to see if the filters are heavily soiled.
Replace filters (Refer to E-14)
•Plasmacluster Air Purifiers emit small traces of ozone
which may produce an odour. These ozone emissions
are below safety levels set by the IEC 60335-2-65.
•Is the unit installed in a location that is difficult for the
sensor to detect cigarette smoke?
•Are the odour sensor openings blocked or clogged?
(In this case, clean the openings.) (Refer to E-15)
The unit does not operate when
cigarette smoke is in the air.
E-16
ERROR DISPLAY
LAMP INDICATION REMEDY
The “Silent” Fan Speed Indi-
cator Light blinks.
Fan motor disconnected or abnormal.
Operation stops.
•Pressing the ON/OFF button will reset the error display,
but if error occurs again, contact the shop where you
purchased the unit.
OPTIONAL STAND
Model : FZ-FC1TS
Please ask for optional stand at your dealer .
In case you prefer free standing installation,
optional stand FZ-FC1TS is available.

中文
目錄
重要安全事項............................................ C-2
•警告 ............................................................................................... C-2
•操作本機的注意事項 ......................................................... C-2
•遙控器限制 ............................................................................... C-3
•產品掛牆安裝時注意事項 ............................................... C-3
•過濾網指南 ............................................................................... C-3
部件名稱 ................................................... C-4
•主機部件 ..................................................................................... C-4
•背部 ............................................................................................... C-4
•附件 ............................................................................................... C-4
準備工作 ................................................... C-5
•安裝遙控器電池 .................................................................... C-5
•使用遙控器 ............................................................................... C-5
安裝 ........................................................... C-6
安裝過濾網 ............................................. C-10
操作 ......................................................... C-12
•主機操作 ................................................................................. C-12
•遙控器操作 ........................................................................... C-13
保養和清潔 ............................................. C-14
•過濾網更換指南 ................................................................ C-14
•主機 ........................................................................................... C-15
•異味感應器 ........................................................................... C-15
•前過濾網 ................................................................................. C-15
規格 ......................................................... C-15
維修前的檢查事項 .................................. C-16
C-1
中文
多謝您購買聲寶FU-28H-A空氣清新機。請仔細
閱讀此說明書﹐以了解正確的使用信息。在使
用本產品之前﹐請務必閱讀“重要安全事項”
這一節。閱讀後請妥善保管此說明書﹐以便日
後翻閱。
聲寶空氣清新機操作原理
空氣清新機經進氣口吸入室內空氣﹐
使其通過機內的活性碳過濾網（除臭
過濾網）和HEPA過濾網（集塵過濾
網）﹐然後從排氣口排出。空氣清新
機通過其內部風扇的操作不斷重複此
過程。當空氣通過時﹐HEPA過濾網
能夠除去灰塵粒子。當異味成分多次
通過活性碳過濾網時﹐便逐步被吸
收。（異味成分也被HEPA過濾網吸
收。）
有些已被過濾網吸附的異味分子可能
會離開過濾網﹐然後隨出風口吹出。
根據不同的使用環境﹐這些異味可能
在比預期更短的時間內變得強烈。在
這種情況下﹐請選購過濾網更換配件
FZ-28SEF。
注意
本空氣清新機用於去除空氣中懸浮的
灰塵和異味﹐而不能去除有害氣體
（如﹕香煙煙霧中含有的一氧化
碳）。如果異味的源頭依然存在﹐異
味將不能徹底被去除。（如﹕來自建
築材料和寵物身上的異味）。
HEPA過濾網
活性碳過濾網

重要安全事項
C-2
當使用電器時﹐必須遵守基本的安全預防措施﹐包括以下各方面﹕
警告 — 為了減少電擊、火災或受傷等危險﹕
•在使用空氣清新機之前請閱讀所有注意事項。
•只能使用220V的插座。
•如果電線或插頭已經損壞﹐或者壁裝電源插座已經鬆脫﹐請勿使用空氣清新機。
•定期清除電源插頭上的灰塵。
•請勿將手指或異物插入進氣口或排氣口。
當拔掉電源插頭時﹐必須緊握插頭而不要拉扯電線。
否則可能導致電擊和/或因短路引起火災。
•請勿在靠近氣體設備或壁爐的地方使用空氣清新機。
•當清潔本機或不使用本機時﹐請從壁裝電源插座上拔掉插頭。
否則可能導致因絕緣不良引起的電擊和/或因短路引起的火災。
•如果電源線損壞﹐必須由生產商或其代理、聲寶公司的特約維修中心或具有相同資格的人員來更換﹐以免
發生危險。
•當使用噴霧殺蟲劑時請勿使用本機﹐或若房間內有油渣、焚香時的煙、點燃香煙的火苗、空氣中的化學氣
體或濕氣重時也不要使用本機。
•清潔空氣清新機時請加以小心。腐蝕性強的清潔劑會損壞本機的表面。
•只有聲寶特約維修人員才能維修本空氣清新機。當需要調整、修理或有任何問題時﹐請聯絡就近的維修人
員。
•電池處理前必須從遙控器中取出﹐並且必須安全處理。
操作本機的注意事項
•請勿堵塞進氣口和排氣口。
•不要靠近或在熱源體上（如可能接觸到蒸汽的場所）使用本機。
•移動本機時﹐請緊握主機。
移動時若握前面板﹐會導致前面板脫落﹐從而摔落主機﹐造成身體損傷。
•請勿在沒有過濾網的情況下操作本機。
•請勿清洗活性碳過濾網和HEPA過濾網。
這不僅不能增強過濾網的性能﹐反而可能會導致電擊或故障。
•只能使用一塊軟布清潔表面。
否則本機表面可能會損壞或破裂。
此外﹐還可能導致感應器故障。