Sharp X-M200DK User manual

This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
Parts marked with “ “ are important for maintaining the safety of the set.
Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.
INSTALLATION MANUAL
SHARP CORPORATION
[ 1 ] GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
[ 2 ] CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
[ 3 ] MX-M200D/MX-M160D/MX-M160 . . . . . . . . . . . . . . . . . . . . . . . 3-1
[ 4 ] AR-SP10/AR-RP10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
[ 5 ] AR-D34/AR-D35 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
[ 6 ] MX-FX10/AR-MM9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
[ 7 ] MX-NB10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
[ 8 ] MX-TR10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
[ 9 ] CHANGING THE COPY PAPER SIZE IN THE TRAY. . . . . . . . . 9-1
[10] ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
[11] AR-PF1 BARCODE FONT KIT
AR-PF2 MACRO FONT FLASH ROM KIT . . . . . . . . . . . . . . . . 11-1
[12] MX-PK10 PS EXPANSION KIT. . . . . . . . . . . . . . . . . . . . . . . . . 12-1
[13] AR-SM5 256Mb EXPANSION MEMORY . . . . . . . . . . . . . . . . . 13-1
DIGITAL
MULTIFUNCTIONAL
SYSTEM
MX-M200D
MX-M200DK
MX-M160D
MX-M160DK
MX-M160
As for the content of the MX-M200DK/MX-M160DK, refer to the
content of the MX-M200D/MX-M160D as long as there is no
CODE : 00ZMXM200DI1E
MX-M200D
MX-M160D
MX-M160
CONTENTS
MODEL

This product is a class 1 laser product that complies with 21CFR 1040.10 and 1040.11 of the CDRH standard and IEC60825-1 Edition 1.2-2001.
1) When a problem in the laser optical unit has occurred, the whole optical unit must be exchanged as a unit, not as individual parts.
3)
2) Do not look into the machine with the main switch turned on after removing the developer unit, toner cartridge, and drum cartridge.
Do not look into the laser beam exposure slit of the laser optical unit with the connector connected when removing and installing the optical
system.
4) The middle frame contains the safety interlock switch.
Do not defeat the safety interlock by inserting wedges or other items into the switch slot.
The following cautions must be observed to avoid exposure of the laser beam to your eyes at the time of servicing.
This laser radiation is not a danger to the skin, but when an exact focusing of the laser beam is achieved on the eye's retina, there is the danger of
spot damage to the retina.
This means that this machine does not produce hazardous laser radiation. The use of controls, adjustments or performance of procedures other
than those specified herein may result in hazardous radiation exposure.
CAUTION
Warning:
This is a Cla
Disconnect the AC cord before servicing the unit.
LASER WAVE - LENGTH: 785 nm + 10 nm/ 15 nm
Pulse times : (8.141 s 0.1 s/7 mm
Output power : 0.14 mW 0.22 mW
ss A product. In a domestic environment this product may cause radio interference in which case
the user may be required to take adequate measures.
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPPARAT

MX-M160D GENERAL 1 - 1
[1] GENERAL
1. Note for servicing
Pictogram
The label ( ) in the fusing area of the machine indicates the
following:
: Caution, risk of danger
: Caution, hot surface
A. Warning for servicing
•The fusing area is hot. Exercise care in this area when removing misfed
paper.
•Do not look directly at the light source. Doing so may damage your
eyes.
B. Cautions for servicing
•Do not switch the machine rapidly on and off. After turning the machine
off, wait 10 to 15 seconds before turning it back on.
•Machine power must be turned off before installing any supplies.
•Place the machine on a firm, level surface.
•Do not install the machine in a humid or dusty location.
•When the machine is not used for a long time, for example, during
prolonged holidays, turn the power switch off and remove the power
cord from the outlet.
•When moving the machine, be sure to turn the power switch off and
remove the power cord from the outlet.
•Do not cover the machine with a dust cover, cloth or plastic film while
the power is on. Doing so may prevent heat dissipation, damaging the
machine.
•Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous laser radiation
exposure.
•The socket-outlet shall be installed near the machine and shall be easily
accessible.
C. Note for installation place
Improper installation may damage the machine. Please note the
following during initial installation and whenever the machine is moved.
Caution : If the machine is moved from a cool place to a warm place,
condensation may form inside the machine. Operation in this
condition will cause poor copy quality and malfunctions. Leave
the machine at room temperature for at least 2 hours before
use.
Do not install your machine in areas that are:
•damp, humid, or very dusty
•poorly ventilated
•exposed to direct sunlight
•subject to extreme temperature or humidity changes, e.g., near an air
conditioner or heater.
The machine should be installed near an accessible power outlet for
easy connection and disconnection.
Be sure to connect the power cord only to a power outlet that meets the
specified voltage and current requirements. Also make certain the outlet
is properly grounded.
Note : Connect the machine to a power outlet which is not used for other
electric appliances. If a lighting fixture is connected to the same
outlet, the light may flicker.
Be sure to allow the required space around the machine for servicing
and proper ventilation.
20 cm
(8
" )
20 cm
(8
" )
20 cm (8
" )

MX-M160D GENERAL 1 - 2
D. Note for handling PWB and electronic parts
When handling the PWB and the electronic parts, be sure to observe the
following precautions in order to prevent against damage by static
electricity.
1) When in transit or storing, put the parts in an anti-static bag or an
anti-static case and do not touch them with bare hands.
2) When and after removing the parts from an anti-static bag (case), use
an earth band as shown below:
• Put an earth band to your arm, and connect it to the machine.
3) When repairing or replacing an electronic part, perform the procedure
on an anti-static mat.

MX-M160D CONFIGURATION 2 - 1
[2] CONFIGURATION
1. System Configurations
2. Machine configuration
[MX-M200D] [MX-M160D] [MX-M160]
(250-sheet paper
feed unit)
(2 x 250-sheet paper
feed unit)
[AR-RP10]
[AR-D35] [AR-D34]
[MX-TR10]
AR-RP10
(REVERSING SINGLE PASS FEEDER)
[AR-SP10] [AR-VR7] [MX-NB10]
(SINGLE PASS FEEDER) (DOCUMENT COVER)
(JOB SEPARATOR)
[MX-FX10]
(FACSIMILE
EXPANSION KIT)
(NEWORK PRINTING /
SCANNING
EXPANSION KIT)
Standard for North America only
MX-M200D MX-M160D MX-M160
Copy STD STD STD
Color scanner STD STD STD
SPLC printer STD STD STD
PCL printer OPT OPT OPT
Fax OPT OPT OPT
Network OPT OPT OPT
Duplex STD STD N/A
Sort STD STD STD
Paper tray 2-stage 1-stage 1-stage

MX-M160D CONFIGURATION 2 - 2
3. Option list
O : Option installation enable X : Option installation disable
Model name Name MX-M200D MX-M160D MX-M160 Product key
target
AR-RP10 REVERSING SINGLE PASS FEEDER North/South America: STD
Europe, Australia, Agency: OPT
OPT N/A —
AR-SP10 SINGLE PASS FEEDER North/South America: N/A
Europe, Australia, Agency: OPT
OPT OPT —
AR-VR7 DOCUMENT COVER North/South America:N/A
Europe, Australia, Agency: OPT
OPT STD —
AR-D34 250-SHEET PAPER FEED UNIT OPT OPT OPT —
AR-D35 2X250-SHEET PAPER FEED UNIT OPT OPT OPT —
MX-TR10 JOB SEPARATOR TRAY KIT OPT OPT OPT —
MX-NB10 NEWORK PRINTING / SCANNING
EXPANSION KIT
OPT OPT OPT —
MX-FX10 FACSIMILE EXPANSION KIT OPT OPT OPT —
AR-SM5 256MB EXPANTION MEMORY BOARD OPT OPT OPT —
AR-MM9 FAX EXPANTION MEMORY BOARD OPT OPT OPT —
AR-PF1 BARCODE FONT KIT OPT OPT OPT —
MX-PK10 PS3 EXPANSION KIT OPT OPT OPT Ye s
AR-PF2 MACRO FONT FLASH ROM KIT OPT OPT OPT —

MX-M200D/MX-M160D/MX-M160 3 - 1
[3] MX-M200D/MX-M160D/MX-M160
1.Installing conditions
A.Copier installation
Do not install your copier in areas that are:
•damp, humid, or very dusty
•exposed to direct sunlight
•poorly ventilated
•subject to extreme temperature or humidity changes, e.g., near an air
conditioner or heater.
•Be sure to allow the required space around the machine for servicing
and proper ventilation.
B.Power source
•Use an exclusive to dedicated power outlet. If the power plug of this
machine is inserted into a power outlet commonly used with other
illumination units, flickers of the lamp may be result. Use a power outlet
which is not used commonly with any illumination units.
•Avoid complex wiring.
C.Grounding wire connection.
•To avoid danger, the power outlet must be grounded. If no grounding
wire is connected and a leakage occurs, a fire or an electric shock may
be result.
2. Removal of protective material and fixing
screw
1) Remove all tapes and protective material.
•Remove all tapes, then open the document cover and remove the
protective material of sheet shape
2) Remove the fixing screw.
•Use a coin to remove the fixing screw.
•The fixing screw is required when transporting the machine. Keep it in
the tray. (Refer to the later description.)
3.Installing procedure
A.Developer cartridge installation
1) Open the bypass tray, and open the side cover.
2) Open the front cover.
•Hold the both sides and pull down to open.
3) Loosen the screw and remove the developer cartridge.
4) Remove the developer tank from the developer cartridge.
5) Shake the developer bag enough before opening it, and supply the
developer into the developer tank.
• While rotating the MG roller in the arrow direction, supply the
developer into the developer tank evenly so as not to overflow.
MG roller

MX-M200D/MX-M160D/MX-M160 3 - 2
6) Check that two hooks of the developer unit is hooked on the toner
cartridge guide, and secure the toner cartridge guide to the
developing unit.
* Check that the DV seal is free from the developer. If developer is
attached to the DV seal, clean it.
* After supplying developer, do not tilt or shake the developer
cartridge.
7) Attach the developer cartridge to the main unit, and secure it with
the screw.
B.Toner cartridge installation
1) Remove the new toner cartridge from the bag. Grasp the cartridge
on both sides and shake it horizontally four or five times.
2) Insert the toner cartridge along the guides until it locks in place while
pushing the lock release lever
•If there is any dirt or dust on the toner cartridge, remove it before
installing the cartridge..
C. Set the toner density reference control level
1) With the front cover open, turn ON the machine power and enter
SIM25-02.
Note: When the machine is not in the simulation mode, if the front
cover is closed and the machine power is turned ON, toner
may be supplied from the toner cartridge to the developer
cartridge.
Under this state, the toner density reference control level
adjustment cannot be made properly.
Therefore, if the front cover is closed and the machine power
is turned ON with the machine not in the simulation mode,
dispose developer and supply new developer and adjust the
toner density reference level.
2) Close the front cabinet.
3) Press [START] key, and execute SIM25-02.
Note: It takes about 3 minutes to execute SIM25-02 completely.
During execution of this simulation, the front cover must not be
opened and the machine power must not be turned OFF.
4. Removal and storage of fixing screw
1) Lift the knob and gently pull out the tray.
2) Hold the paper pressure plate and turn the fixing screw in the arrow
direction.
3) Store the fixing pin and the fixing screw in the tray.
•Store the fixing screw which was removed in the above procedure 2 and
the fixing screw which was removed in procedure 2 of 2.
•Removal of protective material and fixing screw in the storage place in
the tray.
hook
4 or 5 times
Screw
fixing
pin

AR-SP10/AR-RP10 4 - 1
[4] AR-SP10/AR-RP10
1. Unpacking
For unpacking, refer to the figure below.
2. Installation
Turn the main switch of the copier to the “OFF” position and then
remove the power plug of the copier from the outlet.
1) Remove the document cover.
Lift the document cover from the copier and tilt it to the rear side to
remove it.
2) Remove the right cabinet.
Remove the screws and remove the right cabinet.
3) Remove the document glass and the right document glass holder.
Remove the screws, remove the document glass from the copier, and
then remove the right document glass holder.
4) Attach the SPF glass holder.
Fit the SPF glass holder to the document glass.
Attach the document glass to the copier and fix it with the screws.

AR-SP10/AR-RP10 4 - 2
5) Attach the right cabinet.
Reattach the right cabinet to its original position and fix it with the
screws.
6) Cut out the cut-out portion.
Cut out the cut-out portion of the rear cabinet with nippers or the like.
At this time, be careful about the orientation of the nippers so that the
cut plane of the rear cabinet is flat.
7) Attach the automatic document feeder.
Insert the hinge portions of the document feeder into the mounting por-
tions of the copier by holding the feeder at an angle toward the rear
side.
8) Connect the relay connector.
Connect the harness of the automatic document feeder to the connec-
tor of the copier and tighten the screws on the connector.
9) Remove the filament tape.
Remove the filament tape located in the positions shown in the illustra-
tion.

AR-D34/AR-D35 5 - 1
[5] AR-D34/AR-D35
1. Unpacking
(AR-D34)
(AR-D35)
2. Installation
Included parts
1) Remove the document cover.
Lift the document cover from the copier and tilt it to the rear side to
remove it.
2) Remove the rear cabinet.
Remove the screw and remove the cover. Then, remove the five screws
and remove the rear cabinet.
Part name Quantity
Screw M4 x 12 (Fixing plate) 8
Screw M4 x 10 2
Fixing plate 4
Paper size label 1

AR-D34/AR-D35 5 - 2
3) Remove the copier rear cover.
Remove the two screws and remove the rear cover.
4) Make a hole for connector.
• Copier (1-tray model)
Cut out the portion shown in the illustration with nippers or the like.
• Copier (2-tray model)
Press the portion shown in the illustration with a screwdriver or the
like to remove it.
5) Remove the second cassette rear cover.
Remove the rear cover which is attached to the 250-sheet paper feed
unit.
Remove the rear cover (upper stage) from the 500-sheet paper feed
unit.
6) Install the copier onto the 250-sheet paper feed unit.
Put the copier on the 250-sheet paper feed unit, and fix with the fixing
plates and the screws.
Use the small fixed plate for front side of the machine.
• Copier (1-tray model) + 250-sheet paper feed unit
• Copier (2-tray model) + 250-sheet paper feed unit

AR-D34/AR-D35 5 - 3
• Copier (1-tray model) + 500-sheet paper feed unit
• Copier (2-tray model) + 500-sheet paper feed unit
7) Remove the connection gear lock.
Remove the connection gear lock (with the red tug) after setting.
8) Connect the connector
Connect the optional relay harness contained in the 1-tray model (2-tray
model) paper feed unit to the PWB of the copier.
• Optional relay harness
• Copier (1-tray model) + 250-sheet paper feed unit

AR-D34/AR-D35 5 - 4
• Copier (2-tray model) + 250-sheet paper feed unit
• Copier (1-tray model) + 500-sheet paper feed unit
• Copier (2-tray model) + 500-sheet paper feed unit
9) Remove the cassette packing fixtures.
Pull the cassette until it stops.
Turn and remove the packing lock fixture which is fixing the paper pres-
sure plate inside the cassette in the direction of arrow.

MX-FX10 6 - 1
[6] MX-FX10/AR-MM9
1. Unpacking
<Before installation>
• For improvement of workability, some description in this manual as
well as components and accessories may change without prior notice.
In this case, refer to the service manual.
2. Installation
1) Detach the rear cover.
<1>Unscrew two screws from the rear cover.
<2>Push to release the lock shown in the illustration below. Slide to
right and remove the rear cover.
2) Work the rear cover.
Cut and remove the cut-out portion from the rear cover using a tool
such as nippers. Be careful with the tool's direction so that the cut
surface would be flat.
* If no need to install, go on to Step 3 to continue FAX Expansion Kit
Installation.
Insert an additional memory board into the socket of FAX Expansion
Unit. Be careful with the inserting direction. Make sure that it is securely
inserted.
3) Install FAX Expansion Unit.
<1>Hook the attaching parts of FAX Expansion Unit (two on the right)
onto the copier frame as shown.
<2>Hook the attaching part of FAX Expansion Unit (one on the left)
onto the copier frame as shown.
<3>Push the lower left side of the unit to make sure that connectors of
FAX Expansion Unit and the copier are connected.
<4>Secure the unit onto the copier using four supplied screws (S tight)
as shown.<1>Hook the attaching parts of FAX Expansion Unit (two
on the right) onto the copier frame as shown.
Turn off the main switch of the copier and then remove the power plug
of the copier from the outlet.
Parts included
FAX Expansion Unit: 1
FAX keyboard: 1
Core: 2
(200V series only)
FCC label : 1
(USA, Canada only) Operation manual: 1
line cable: 1
Screws (S tight): 4
Writing label: 4
A-TICK label: 1
(Australia,
New Zealand only)
Line Adapter: 1
(Australia/New Zealand
/Hong Kong only)
Installing additional memory board (AR-MM9)

MX-FX10 6 - 2
4) Reattach the rear cover.
<1>Insert the claw locks of the rear cover into the copier, and slide it to
left until they are securely locked.
<2>Secure the cover using two screws.
5) Remove keyboard back cover.
<1>Unscrew two screws from the keyboard back cover.
<2>Release the lock as shown, and remove the back cover.
6) Remove dummy panel.
<1>Unscrew from the dummy panel.
<2>Disengage the pawls, and remove it from the copier.
7) Attach FAX keyboard.
<1>Connect the copier flat cable to FAX keyboard.
<2>Place the FAX keyboard onto the copier while engaging the pawls.
<3>Secure the keyboard using a screw.
8) Reattach keyboard back cover.
<1>Insert the claw lock of the keyboard back cover into the copier.
Make sure that the claw lock is securely inserted.
<2>Secure the cover using two screws.

MX-FX10 6 - 3
9) Paste label on the rear cabinet of the copier.
After installing FAX Expansion Kit, paste the supplied label on the
position shown in the illustration.
10) Setup date and time.
Press [FUNCTION] key on the Operation Panel, select [Key
Operator Program], enter 5-digit key operator code, and select
[FAX] mode.
Select [Initial setup] and then [Date and Time]. Enter date in the
order of year, Month, Day and press [OK] to set.
Select [Time Setup], enter time in the order of Hour and Minute, and
press [OK] to set.
11) Clear image memory.
* When additional memory board (AR-MM9) is installed, you must
clear the memory using the Simulation [66-10]. If no additional
memory is installed, there is no need for this memory clear process.
12) Connect line cable.
Connect the line cable to the FAX Expansion Kit.
Even when connecting the telephone line to TEL line, attach the core to
the telephone line.
USA, Canada only
In order to manifest the compliance with FCC Part 68 and IC CS-03, it
is required to provide the machine with the FCC Registration Number
(USA), Ringer Equivalence (USA) and Ringer Eqivalence(Canada).
After installing the FAX expansion kit in the machine, please put the
registration label, packed with the kit, on the prescribed location.
Australia, New Zealand only
A-TICK label attachment.
Insert the power plug of the copier to the outlet, and then turn on the
main switch of the copier.
200V Series Only

MX-NB10 7 - 1
[7] MX-NB10
1. UNPACKING AND INSTALLATION
1-1. UNPACKING
1-2. PACKAGED GOODS
1-3. INSTALLATION PROCEDURE
Turn off the main switch of the main unit and remove the power
plug of the main unit from the outlet.
1) Cut out the cut-out portions from the rear cabinet.
1) Cut out three cut-out portions from the rear cabinet using a cutter or
the like.
2) Use a Phillips screwdriver or the like to open a hole.
2) Attach the network expansion kit.
Connect the connector of the network expansion kit to the connector of
the main unit and put excessive harness into the cut-out portion in the
main unit.
Engage the two pawls on the rear of the network expansion kit with the
cut-out portions of the main unit and network expansion kit using the
supplied screw (3 x 14).
3) Connect the USB cable and the network cable.
1) Attach the supplied cable clamp to the position shown in the illustra-
tion.
2) Connect the USB cable to the network expansion kit and the main
unit. At this time, reduce slack of the cable with the cable clamp as
shown in the illustration.
3) Connect the network cable.
Insert the power plug of the copier to the outlet, turn the main
switch of the copier to the "ON" position, and perform network set-
ting and installation of the software.
3
Phillips screwdriver
Screw (M3x14)
Connector
Pawl
Pawl

MX-NB10 7 - 2
2. SETUP IN A WINDOWS ENVIRONMENT
2-1. SETTING THE IP ADDRESS OF THE MACHINE
Before installing the printer driver, be sure to set the IP address of the
machine as explained in “System Settings” in the “Network Printer”
manual on the CD-ROM. Consult your network administrator for the
correct IP address, subnet mask, and default gateway to be entered. If
a DHCP server will automatically assign an IP address to the machine,
the following procedure is not necessary. (To check the IP address
assigned to the machine by DHCP, see “2-2. CHECKING THE IP
ADDRESS”.)
Caution: If the machine is used in a DHCP environment, the machine's
IP address may change automatically. If this happens, printing
will no longer be possible. In this event, use a WINS server or
do not use the machine in a DHCP environment.
2-2. CHECKING THE IP ADDRESS
There are several settings where the IP address must be entered or
checked.
To check the IP address of the machine, hold down the status button on
the network expansion kit at least 2 seconds to print out a Printer Set-
ting List.
Caution: How to reset the network expansion kit
To reset the network expansion kit, power on the machine
while holding down the status button on the network expansion
kit.
Network scanner destination information and scanning set-
tings will remain after the network expansion kit is reset, how-
ever, the network settings and network printer settings will
revert to the factory default settings.
Status
button

MX-TR10 8 - 1
[8] MX-TR10
1. Unpacking
<Before installation>
• For improvement of workability, some description in this manual as
well as components and accessories may change without prior
notice.In this case, refer to the service manual.
2. Installation
2-1. Remove the right cabinet and the right front cab-
inet.
1) Open the document cover or the document feeder.
2) Open the bypass tray.
3) Remove the right door.
4) Open the front cover
5) Remove the five screws and then remove the right cabinet.
6) Remove the screw and then remove the right front cabinet.
2-2. Attach the separator motor unit.
1) Connect the connector.
2) Insert the two bosses of the copier into the positioning holes of the
separator motor unit and secure it with the supplied screw.
2-3. Arrange the wiring of the separator motor unit.
1) Insert the excessive cord into the clamp attached on the separator
motor unit and arrange the wiring as shown in the illustration.
2-4. Move the separator lever.
1) Rotate the separator gear to move the lever to the position shown in
the illustration. Do not move the lever position until operation check
is performed.
Turn off the main switch of the copier and then remove the power plug
of the copier from the outlet.