Siemens SWT-3000 Technical Document

Smart Communication
SWT 3000 Teleprotection
P3.5.186 and higher
Equipment Manual
C53000-G6040-C605-1
Preface
Open Source Software
Table of Contents
Safety Instructions 1
Functional Description 2
Installation and Commissioning 3
Diagnostics and Error Handling 4
PowerSys and Auxiliary Software Tools 5
SNMP and Remote Access 6
Processing Unit Module 7
Interface Command Module 8
Digital Line Equipment 9
Copper Line Equipment Module 10
Fiber Optic Module 11
Alarm Module 12
Power Supply 13
Technical Data 14
Appendix A
Index

i
i
NOTE
For your own safety, observe the warnings and safety instructions contained in this document, if available.
Disclaimer of Liability
Subject to changes and errors. The information given in
this document only contains general descriptions and/or
performance features which may not always specifically
reflect those described, or which may undergo modifica-
tion in the course of further development of the products.
The requested performance features are binding only when
they are expressly agreed upon in the concluded contract.
Document version: C53000-G6040-C605-1.00
Edition: 03.2020
Version of the product described: P3.5.186 and higher
Copyright
Copyright © Siemens 2020. All rights reserved.
The disclosure, duplication, distribution and editing of this
document, or utilization and communication of the content
are not permitted, unless authorized in writing. All rights,
including rights created by patent grant or registration of a
utility model or a design, are reserved.

Preface
Purpose of the Manual
This manual describes the control and monitoring functions for Smart Communications.
Target Audience
Smart Communications engineers, protection system engineers, commissioning engineers, persons entrusted
with the setting, testing and maintenance of automation, selective protection and control equipment, and
operating personnel in electrical installation and power plants.
Scope
This manual is valid for the SWT 3000 device family.
Further Documentation
[dw_Product-overview_SWT3000_Equipment-manual, 1, en_US]
•Product Information
The Product Information includes general information about device installation, technical data, limit
values for input and output modules, and conditions when preparing for operation. This document is
delivered with each device.
•Equipment Manual
The Equipment Manual describes the functions and applications of SWT 3000 devices.
Indication of Conformity
This product complies with the directive of the Council of the European Communities
on harmonization of the laws of the Member States relating to electromagnetic
compatibility (EMC Directive 2014/30/EU) and concerning electric equipment for use
within specified voltage limits (Low Voltage Directive 2014/35/EU).
This conformity has been proved by tests performed according to the Council Directive
in accordance with the generic standards EN 61000-6-2 and EN 61000-6-4 (for EMC
directive), and with the standard EN 60950-1 (for Low Voltage Directive) by Siemens
AG.
The device is designed and manufactured for application in an industrial environment.
The product conforms with the international standards of IEC 60870.
Smart Communication, SWT 3000 Teleprotection, Equipment Manual 3
C53000-G6040-C605-1, Edition 03.2020

The device is designed and manufactured for application in industrial environment:
•Emitted interference: EN 61000-6-4: 2001
•Immunity to interference: EN 61000-6-2: 2001
For use in residential areas you also need the individual authorization of a national authority or test agency
with respect to emitted interference.
The test and connection jacks accessible at the front are not isolated interfaces and are only used for mainte-
nance purposes. The usual ESD measures must be observed in use. This also applies for the use of telephone
connection sockets (if present).
i
i
NOTE
All signal and data cables are shielded and connection of the shielding over a large area must be provided
at both ends.
The products and systems listed here are manufactured and marketed using a DQS-certified quality manage-
ment system in accordance with ISO 9001.
Additional Support
For questions about the system, contact your Siemens sales partner.
Support
Our Customer Support Center provides a 24-hour service.
Siemens AG
Customer Support Center
Humboldtstraße 59
90459 Nürnberg
Germany
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
Notes on Safety
This document is not a complete index of all safety measures required for operation of the equipment (module
or device). However, it comprises important information that must be followed for personal safety, as well as
to avoid material damage. Information is highlighted and illustrated as follows according to the degree of
danger:
!
DANGER
DANGER means that death or severe injury will result if the measures specified are not taken.
²Comply with all instructions, in order to avoid death or severe injuries.
!
WARNING
WARNING means that death or severe injury may result if the measures specified are not taken.
²Comply with all instructions, in order to avoid death or severe injuries.
Preface
4 Smart Communication, SWT 3000 Teleprotection, Equipment Manual
C53000-G6040-C605-1, Edition 03.2020

!
CAUTION
CAUTION means that medium-severe or slight injuries can occur if the specified measures are not taken.
²Comply with all instructions, in order to avoid moderate or minor injuries.
!
CAUTION
ESD (Electrostatic sensitive devices) means that a device or component can be damaged by common static
charges built up on people, tools, and other non-conductors or semiconductors.
²Comply with all instructions, in order to avoid moderate or minor injuries.
NOTICE
NOTICE means that property damage can result if the measures specified are not taken.
²Comply with all instructions, in order to avoid property damage.
i
i
NOTE
Important information about the product, product handling or a certain section of the documentation
which must be given attention.
Used Symbols on Device
No. Symbol Description
1 Direct current, IEC 60417, 5031
2 Alternating current, IEC 60417, 5032
3 Direct and alternating current, IEC 60417, 5033
4 Earth (ground) terminal, IEC 60417, 5017
5 Protective conductor terminal, IEC 60417, 5019
6 Caution, risk of electric shock
7 Caution, risk of danger, ISO 7000, 0434
8 Protective Insulation, IEC 60417, 5172, Safety Class II devices
Preface
Smart Communication, SWT 3000 Teleprotection, Equipment Manual 5
C53000-G6040-C605-1, Edition 03.2020

No. Symbol Description
9 Guideline 2002/96/EC for electrical and electronic devices
10 Guideline for the Eurasian Market
Preface
6 Smart Communication, SWT 3000 Teleprotection, Equipment Manual
C53000-G6040-C605-1, Edition 03.2020

Open Source Software
The product contains, among other things, Open Source Software developed by third parties. The Open
Source Software used in the product and the license agreements concerning this software can be found in the
Readme_OSS. These Open Source Software files are protected by copyright. Your compliance with those
license conditions will entitle you to use the Open Source Software as foreseen in the relevant license. In the
event of conflicts between Siemens license conditions and the Open Source Software license conditions, the
Open Source Software conditions shall prevail with respect to the Open Source Software portions of the soft-
ware. The Open Source Software is licensed royalty-free. Insofar as the applicable Open Source Software
License Conditions provide for it you can order the source code of the Open Source Software from your
Siemens sales contact – against payment of the shipping and handling charges – for a period of at least 3
years after purchase of the product. We are liable for the product including the Open Source Software
contained in it pursuant to the license conditions applicable to the product. Any liability for the Open Source
Software beyond the program flow intended for the product is explicitly excluded. Furthermore any liability
for defects resulting from modifications to the Open Source Software by you or third parties is excluded. We
do not provide any technical support for the product if it has been modified.
Smart Communication, SWT 3000 Teleprotection, Equipment Manual 7
C53000-G6040-C605-1, Edition 03.2020

8 Smart Communication, SWT 3000 Teleprotection, Equipment Manual
C53000-G6040-C605-1, Edition 03.2020

Table of Contents
Preface..........................................................................................................................................................3
Open Source Software..................................................................................................................................7
1 Safety Instructions......................................................................................................................................19
1.1 Scope of Delivery.............................................................................................................. 20
1.2 Transport, Package, Storage.............................................................................................. 21
1.2.1 Unpacking the Device.................................................................................................. 21
1.2.2 Repacking the Device...................................................................................................21
1.2.3 Storing the Device....................................................................................................... 21
1.3 Incoming Inspection..........................................................................................................22
1.3.1 Safety Notes................................................................................................................22
1.3.2 Performing a Follow-Up Inspection on a Device............................................................22
1.3.3 Checking Rated Data and Functions............................................................................. 22
1.4 Electrical Inspection.......................................................................................................... 23
1.4.1 Device Protection........................................................................................................ 23
1.4.2 Grounding a Device..................................................................................................... 23
1.4.3 Connecting the Device.................................................................................................23
1.4.4 Safety Notes................................................................................................................24
1.4.5 Performing the Electrical Inspection............................................................................. 24
1.5 Electrostatic Sensitive Devices........................................................................................... 25
1.6 Installation........................................................................................................................27
1.6.1 Preparing Installation...................................................................................................27
1.6.2 Power Supply.............................................................................................................. 27
1.6.3 Installation of Plug-In Module...................................................................................... 28
1.6.4 Completing Installation................................................................................................28
1.7 Replacement.....................................................................................................................29
1.7.1 Preparing for Replacement...........................................................................................29
1.7.2 Completing Replacement.............................................................................................30
2 Functional Description............................................................................................................................... 31
2.1 Device Description and Features........................................................................................32
2.1.1 Overview.....................................................................................................................32
2.1.2 Quick Overview of the Features................................................................................... 32
2.2 Applications for Transmission............................................................................................34
2.2.1 Applications for Digital Transmission............................................................................34
2.2.2 Applications for Analog and/or Digital Transmission..................................................... 34
2.2.3 Combination of Analog and Digital Interfaces...............................................................35
2.2.4 Transmission Paths...................................................................................................... 35
Smart Communication, SWT 3000 Teleprotection, Equipment Manual 9
C53000-G6040-C605-1, Edition 03.2020

2.2.5 Modes of Operation.....................................................................................................36
2.2.5.1 Analog Mode Operation......................................................................................... 36
2.2.5.2 Digital Mode Operation.......................................................................................... 36
2.2.6 Features...................................................................................................................... 36
2.3 Operating Modes with PLC Equipment...............................................................................38
2.3.1 Overview.....................................................................................................................38
2.3.2 Single Purpose Operation.............................................................................................38
2.3.3 Multi-Purpose Operation..............................................................................................38
2.3.4 Alternate Multi-Purpose Operation...............................................................................38
2.4 Equipment Versions.......................................................................................................... 40
2.4.1 Overview.....................................................................................................................40
2.4.2 Broadband Version...................................................................................................... 40
2.4.3 Narrow-Band Version...................................................................................................41
2.4.4 Applications for Narrow-Band Devices..........................................................................41
2.5 Possible Ways of Using the SWT 3000................................................................................44
2.5.1 Analog Transmission Path............................................................................................ 44
2.5.2 Digital Transmission Path.............................................................................................45
2.5.3 Analog and Digital Transmission Path...........................................................................46
2.5.4 Integrated Into the PowerLink PLC System....................................................................47
2.6 Monitoring........................................................................................................................49
2.7 Protection Modes.............................................................................................................. 50
2.7.1 Overview.....................................................................................................................50
2.7.2 Unblocking Mode........................................................................................................ 50
2.7.3 Description of the Protection Operating Modes............................................................ 51
2.7.3.1 Overview............................................................................................................... 51
2.7.3.2 Mode 1 (Double System Protection)....................................................................... 51
2.7.3.3 Mode 2 (Single Phase Protection)........................................................................... 52
2.7.3.4 Mode 3 (4 Commands with Priority)....................................................................... 52
2.7.3.5 Mode 3a (4 Independent Commands, 4iC)..............................................................53
2.7.3.6 Mode 3b (2 plus 2).................................................................................................54
2.7.3.7 Mode 4 (Only One Command Active)......................................................................57
2.7.3.8 Mode 5A (3 Independent Commands).................................................................... 57
2.7.3.9 Mode 5D (Only for Digital Transmission Paths)........................................................58
2.8 Frequency Overview......................................................................................................... 59
2.8.1 Broadband Devices in the VF Range [kHz].....................................................................59
2.8.2 Narrow-Band Devices in the VF Range [kHz]................................................................. 59
2.8.3 Frequency Diagram for Broadband and Narrow-Band Devices.......................................61
2.8.4 Command Duration for Single-Purpose Operation........................................................ 61
2.8.4.1 Mode 1, Mode 2, Mode 3a, Mode 3b, Mode 4 , Mode 5A........................................ 61
2.8.4.2 4 Commands with Priority Mode 3..........................................................................62
2.8.5 Command Duration for Alternate Multi-Purpose Operation...........................................62
2.9 Fiber-Optic Connection..................................................................................................... 63
2.9.1 Overview.....................................................................................................................63
2.9.2 Connection to the PowerLink PLC System.....................................................................63
2.9.3 Connection to a Multiplexer supporting IEEE C37.94 Protocol.......................................64
2.9.4 Connection to a Multiplexer via FO-Box........................................................................65
2.9.5 Direct Connection via Fiber-Optic Cable....................................................................... 66
2.10 Remote Monitoring, Service Channel, and IP Network........................................................67
2.10.1 RM with Analog Interface.............................................................................................67
Table of Contents
10 Smart Communication, SWT 3000 Teleprotection, Equipment Manual
C53000-G6040-C605-1, Edition 03.2020

2.10.2 RM with Digital Interface............................................................................................. 68
2.10.3 Service Channel...........................................................................................................68
2.10.4 IP Interface to SWT 3000..............................................................................................68
2.11 IEC 61850.........................................................................................................................70
2.11.1 Ethernet EN100 Module with IEC 61850 Protocol.........................................................70
2.11.2 IEC 61850 Introduction................................................................................................71
2.11.3 Logical Nodes.............................................................................................................. 75
2.12 Tele Protection Over Packet TPoP.......................................................................................80
2.12.1 Introduction................................................................................................................ 80
2.12.2 Cyber Security............................................................................................................. 81
2.12.3 Protection Command Transmission.............................................................................. 82
2.12.4 RM Transmission......................................................................................................... 83
2.12.5 Line Clock Synchronization.......................................................................................... 83
2.12.6 Line Quality Supervision.............................................................................................. 84
2.12.7 QoS (Quality of Service)...............................................................................................86
2.13 Cyber Security...................................................................................................................88
2.13.1 Overview.....................................................................................................................88
2.13.2 Certification................................................................................................................ 88
2.13.3 HTTPS Connection....................................................................................................... 89
2.14 Power Supply.................................................................................................................... 92
2.14.1 Stand-Alone Unit......................................................................................................... 92
2.14.2 Integrated Unit............................................................................................................ 92
2.15 Virtual Display...................................................................................................................93
2.16 T-Scheme..........................................................................................................................94
2.17 Command Loop Test......................................................................................................... 96
3 Installation and Commissioning.................................................................................................................97
3.1 Installation........................................................................................................................98
3.1.1 Connecting Plugs.........................................................................................................98
3.1.2 Equipment of the Subrack............................................................................................99
3.1.3 Cable Installation.......................................................................................................100
3.2 Pinouts of SWT 3000 Modules......................................................................................... 101
3.2.1 Pinout of the IFC-x Module.........................................................................................101
3.2.2 Pinout of the PU4 Module.......................................................................................... 102
3.2.3 Connection of Digital Line Interfaces..........................................................................104
3.2.4 Signals for the Digital Line Interface 1........................................................................ 104
3.2.5 Signals for the Digital Line Interface 2........................................................................ 105
3.2.6 Pinout of the SC interface.......................................................................................... 106
3.2.7 Pinout of the SSB interface.........................................................................................106
3.2.8 Pinout of the CLE Module...........................................................................................106
3.2.9 Pinout of the ALR Module.......................................................................................... 107
3.2.10 Pinout of the Fiber-Optic Module............................................................................... 108
3.3 Jumper Settings for SWT 3000 Modules...........................................................................110
3.3.1 General Information.................................................................................................. 110
3.3.2 Jumper Settings for IFC Modules................................................................................ 110
3.3.2.1 Overview............................................................................................................. 110
3.3.2.2 DIP Switches on IFC Modules................................................................................ 112
Table of Contents
Smart Communication, SWT 3000 Teleprotection, Equipment Manual 11
C53000-G6040-C605-1, Edition 03.2020

3.3.3 Jumper Settings for the PU4 Module.......................................................................... 113
3.3.4 Jumper Settings for the DLE Module.......................................................................... 114
3.3.4.1 Overview............................................................................................................. 114
3.3.4.2 Jumper Settings for the Selection of Digital Line Interfaces LID-1...........................114
3.3.4.3 Jumper Settings for the Selection of Digital Line Interfaces LID-2...........................114
3.3.4.4 Selection of the Input Gain for G703.6 Interfaces..................................................115
3.3.4.5 DLE Settings for the LID-x Connection via FOM..................................................... 115
3.3.5 Jumper Settings for the CLE Module...........................................................................115
3.3.6 Jumper Settings of the FO-Box................................................................................... 116
3.3.7 Jumper Settings of the ALR Module............................................................................116
3.3.8 Power Supply Jumper Settings................................................................................... 117
3.4 Start Commissioning....................................................................................................... 119
3.4.1 Before Starting the Commissioning............................................................................ 119
3.4.2 Switching on the Power Supply..................................................................................119
3.4.3 Switching on the Device (with PU4 Module)...............................................................119
3.4.4 Connecting the Service PC......................................................................................... 121
3.5 Device Configuration.......................................................................................................122
3.5.1 New Configuration.................................................................................................... 122
3.5.2 Programming the Device........................................................................................... 124
3.5.3 System Configuration................................................................................................ 125
3.5.3.1 Operating Mode...................................................................................................125
3.5.3.2 Line Interface.......................................................................................................126
3.5.3.3 Transmitter and Receiver Address for digital interfaces..........................................127
3.5.3.4 Reflection............................................................................................................ 127
3.5.3.5 Continuous Signaling (Analog Transmission Path).................................................128
3.5.4 System-2 Configuration............................................................................................. 128
3.5.4.1 Overview............................................................................................................. 128
3.5.4.2 Command Interface............................................................................................. 129
3.5.4.3 Special Allocation.................................................................................................131
3.5.4.4 Power Supply....................................................................................................... 133
3.5.4.5 Application.......................................................................................................... 134
3.5.5 Output Allocation...................................................................................................... 134
3.5.6 Free Allocation.......................................................................................................... 135
3.5.7 Signaling Allocation...................................................................................................136
3.5.8 RM Configuration...................................................................................................... 137
3.5.9 Timer Configuration.................................................................................................. 139
3.5.9.1 Configuration of the System Timers......................................................................139
3.5.9.2 Configuration of the Command Input .................................................................. 140
3.5.9.3 Timer Settings for the Command Output.............................................................. 143
3.5.9.4 Timer Setting Options for Mode 3b.......................................................................145
3.5.9.5 Broadband Versions............................................................................................. 146
3.5.9.6 Narrow-Band Versions..........................................................................................148
3.5.10 Fiber-Optic Configuration.......................................................................................... 149
3.5.10.1 Overview............................................................................................................. 149
3.5.10.2 System Configuration...........................................................................................149
3.5.11 TPoP Configuration....................................................................................................150
3.5.12 Clock Synchronization............................................................................................... 154
3.5.13 IP Network Configuration...........................................................................................157
3.5.14 Alarm Configuration.................................................................................................. 161
3.5.14.1 Alarm Output Allocation for ALR........................................................................... 161
3.5.14.2 Alarm Output Allocation for IFC............................................................................ 163
3.5.14.3 Alarm Output Allocation for IEC 61850 / SNMP..................................................... 165
Table of Contents
12 Smart Communication, SWT 3000 Teleprotection, Equipment Manual
C53000-G6040-C605-1, Edition 03.2020

3.5.14.4 Setting Options for SWT 3000 Alarms................................................................... 166
3.5.14.5 Unblocking Impulse Allocation for IFC...................................................................167
3.5.15 T-Scheme Configuration............................................................................................ 167
3.5.16 Command Loop Test Configuration............................................................................170
3.6 Online Parameter Adjustment......................................................................................... 171
3.6.1 Overview...................................................................................................................171
3.6.2 Level Adjustment for Analog Interface....................................................................... 171
3.6.2.1 Tx Level Adjustment.............................................................................................171
3.6.2.2 Rx Level Adjustment.............................................................................................171
3.6.3 Level Adjustment for Connection via VFx Module....................................................... 173
3.6.3.1 Overview............................................................................................................. 173
3.6.3.2 Connection via a VFx Module............................................................................... 173
3.6.4 Setting Parameters of Measuring Points..................................................................... 174
3.6.5 Time and Date........................................................................................................... 174
4 Diagnostics and Error Handling................................................................................................................177
4.1 Control and Signaling Elements.......................................................................................178
4.1.1 Control and Signaling for PU4 Module........................................................................178
4.1.1.1 Front Panel.......................................................................................................... 178
4.1.1.2 Significance of LEDs on the PU4 Module............................................................... 179
4.1.1.3 IP (Ethernet) and Local (Service) Interface............................................................ 180
4.1.2 Control and Signaling for CLE Module........................................................................ 180
4.1.2.1 Alarm Displays..................................................................................................... 180
4.1.2.2 Test Sockets......................................................................................................... 181
4.1.3 Control and Signaling for FOM Module...................................................................... 181
4.1.3.1 Signification of the Alarm LED on the FOM........................................................... 181
4.1.4 IFC Control and Signaling...........................................................................................183
4.1.5 Control and Signaling for ALR Module........................................................................ 184
4.1.5.1 Relay Outputs...................................................................................................... 184
4.1.5.2 Visual Indication...................................................................................................184
4.1.5.3 Test Switch S1......................................................................................................184
4.1.6 Control and Signaling for Power Supply..................................................................... 185
4.1.6.1 Displays............................................................................................................... 185
4.2 IFC Test Mode................................................................................................................. 187
4.3 PU4 Test Command.........................................................................................................188
4.3.1 The Dialog Commands...............................................................................................188
4.4 Possible Reasons for the Alarms.......................................................................................190
4.5 Display of the Entries in the Event Recorder..................................................................... 191
4.6 Alarm Messages in the Service Program PowerSys........................................................... 194
4.7 Diagnosis of Ethernet EN100 Module.............................................................................. 195
4.8 FOM SFP Alarm Supervision.............................................................................................198
5 PowerSys and Auxiliary Software Tools................................................................................................... 201
5.1 PowerSys Installation...................................................................................................... 202
5.1.1 About the Service Program PowerSys......................................................................... 202
5.1.2 PC Requirements....................................................................................................... 202
5.1.3 Installation of the Service Program PowerSys............................................................. 202
5.2 PowerSys Startup............................................................................................................ 205
5.2.1 Overview...................................................................................................................205
Table of Contents
Smart Communication, SWT 3000 Teleprotection, Equipment Manual 13
C53000-G6040-C605-1, Edition 03.2020

5.2.2 The Options Menu..................................................................................................... 207
5.2.2.1 Create System Log............................................................................................... 207
5.2.2.2 Measuring Tool.................................................................................................... 207
5.2.2.3 MergeTool........................................................................................................... 207
5.2.2.4 Upload EN100 Parameter..................................................................................... 208
5.2.2.5 Connection.......................................................................................................... 208
5.2.2.6 User Level and Setting Passwords......................................................................... 210
5.2.2.7 Language Options................................................................................................212
5.2.3 The PowerSys Menu.................................................................................................. 212
5.2.3.1 Overview............................................................................................................. 212
5.2.3.2 Print Preview........................................................................................................213
5.2.3.3 Firmware-Release Export......................................................................................214
5.2.3.4 Firmware-Release Import......................................................................................216
5.2.4 The Data Source Menu...............................................................................................217
5.2.4.1 Overview............................................................................................................. 217
5.2.4.2 Device................................................................................................................. 217
5.2.4.3 Remote Device..................................................................................................... 217
5.2.4.4 Data Source > File................................................................................................ 218
5.2.4.5 Data Source > New...............................................................................................219
5.2.4.6 PowerSys Offline Tree Window............................................................................. 220
5.2.4.7 PowerSys Startup Parameter.................................................................................221
5.3 PowerSys Online Connection...........................................................................................224
5.3.1 Overview...................................................................................................................224
5.3.2 Firmware-Overview Menu......................................................................................... 225
5.4 MemTool Installation...................................................................................................... 227
5.4.1 General Information.................................................................................................. 227
5.4.1.1 Overview............................................................................................................. 227
5.4.1.2 System Requirements...........................................................................................227
5.4.1.3 Version of MemTool............................................................................................. 227
5.4.2 Installation of MemTool............................................................................................. 227
5.4.3 Basic Settings............................................................................................................ 229
5.4.3.1 Starting MemTool................................................................................................ 229
5.4.3.2 MemTool Settings................................................................................................ 230
5.4.4 Getting Started..........................................................................................................237
5.5 PU4 Firmware Upgrade with Mem Tool............................................................................239
5.5.1 Connecting the PC..................................................................................................... 239
5.5.2 Starting MemTool......................................................................................................239
5.5.3 Connection to the SWT 3000 Target...........................................................................241
5.5.4 Programming the Application into the Flash Memory................................................. 241
5.5.5 Trouble Shooting.......................................................................................................245
5.5.6 PowerSys Release Upgrade Check.............................................................................. 246
5.6 EN100 Firmware Upgrade............................................................................................... 248
5.7 SWTStraps for Jumper Settings........................................................................................ 250
5.7.1 Overview...................................................................................................................250
5.7.2 SWTStraps Input Form............................................................................................... 250
5.7.3 The Straps Settings windows..................................................................................... 252
5.8 MergeTool for IEC 61850................................................................................................ 255
5.8.1 Overview...................................................................................................................255
5.8.2 Parameter Generator................................................................................................. 255
5.8.3 EN100 Settings..........................................................................................................262
Table of Contents
14 Smart Communication, SWT 3000 Teleprotection, Equipment Manual
C53000-G6040-C605-1, Edition 03.2020

5.9 SWT vDisp for Virtual Display........................................................................................... 267
5.9.1 Installation................................................................................................................ 267
5.9.2 Dashboard.................................................................................................................267
5.9.3 Display Command Counter........................................................................................ 268
5.9.4 Display Event Log / Alarm...........................................................................................270
6 SNMP and Remote Access........................................................................................................................ 273
6.1 Remote Access and Remote Monitoring...........................................................................274
6.1.1 Overview...................................................................................................................274
6.1.2 Remote Access via Intranet (TCP/IP)............................................................................274
6.1.3 Remote Monitoring/Maintenance via Inband RM-Channel...........................................275
6.2 SNMP..............................................................................................................................276
6.2.1 SNMP Function..........................................................................................................276
6.2.2 Spontaneous Indication SNMP Traps.......................................................................... 278
6.2.3 Simple Network Management Protocol Version 3 (SNMPv3)....................................... 279
6.2.3.1 SNMPv3 Overview................................................................................................279
6.2.3.2 SNMPv3 Configuration......................................................................................... 280
6.2.3.3 USM User Management........................................................................................281
6.2.3.4 VACM Management............................................................................................. 283
6.2.3.5 Key Reset............................................................................................................. 286
6.2.3.6 Notification..........................................................................................................286
6.2.4 SNMP Configuration in SWT 3000 Web Interface........................................................ 289
6.2.4.1 Overview............................................................................................................. 289
6.2.4.2 SNMP V2 Trap-Destination Table...........................................................................290
6.2.4.3 Access Password.................................................................................................. 291
6.2.4.4 Activation of Settings........................................................................................... 292
6.2.5 NMS Commissioning..................................................................................................293
6.3 Remote Access................................................................................................................294
6.3.1 General Information.................................................................................................. 294
6.3.1.1 Overview............................................................................................................. 294
6.3.1.2 Remote Access Example....................................................................................... 295
6.3.2 Inband RM-Channel................................................................................................... 295
6.3.3 Route Coupling via SSB.............................................................................................. 296
6.4 Web Interface................................................................................................................. 299
6.4.1 Overview...................................................................................................................299
6.4.2 Ethernet Interface Settings........................................................................................ 300
6.4.3 NTP Settings.............................................................................................................. 301
6.4.4 NTP Daylight Saving Time.......................................................................................... 302
6.4.5 SNMP Settings........................................................................................................... 303
6.4.6 Access Password........................................................................................................303
6.4.7 Activation of Settings.................................................................................................304
7 Processing Unit Module............................................................................................................................307
7.1 Functions of the PU4 module.......................................................................................... 308
7.1.1 Overview...................................................................................................................308
7.1.2 Functional Units........................................................................................................ 312
7.1.3 Internal Power Supply................................................................................................312
7.1.4 Controller.................................................................................................................. 312
7.1.5 Analog Line Interface.................................................................................................312
7.1.6 Self-test.....................................................................................................................313
Table of Contents
Smart Communication, SWT 3000 Teleprotection, Equipment Manual 15
C53000-G6040-C605-1, Edition 03.2020

7.1.7 Interference-Level Evaluation.....................................................................................313
7.1.8 Event Memory and Real-Time Clock............................................................................313
7.1.9 Clock Synchronization............................................................................................... 314
7.1.10 Front Panel................................................................................................................314
7.1.11 IP (Ethernet) and Local (Service) Interface.................................................................. 315
7.1.11.1 Access to the Stand-alone SWT 3000.................................................................... 315
7.1.11.2 Access to the Integrated SWT 3000 (iSWT)............................................................315
8 Interface Command Module.....................................................................................................................317
8.1 General Information........................................................................................................318
8.1.1 Overview...................................................................................................................318
8.1.2 Exclusively Analog Transmission Interface or Analog Secondary Path..........................318
8.1.3 Exclusively Digital Transmission Interfaces................................................................. 318
8.1.4 Description of Operation............................................................................................318
8.1.4.1 Overview............................................................................................................. 318
8.1.4.2 Connection Principle............................................................................................ 319
8.1.5 Controller.................................................................................................................. 321
8.1.6 Test Mode................................................................................................................. 321
8.1.6.1 Overview............................................................................................................. 321
8.1.6.2 Displays............................................................................................................... 322
8.1.7 Slot and Module Identifier .........................................................................................322
8.1.8 Signal Acquisition via Binary Inputs............................................................................ 324
8.1.9 Signal Output from the IFC-D/P Module......................................................................325
8.1.10 Signal Output from IFC-S Module............................................................................... 326
8.1.11 Pinout of the IFC-x Module.........................................................................................326
8.2 Block Diagrams of IFC Modules........................................................................................328
8.2.1 IFC-D Module.............................................................................................................328
8.2.2 IFC-P Module............................................................................................................. 329
8.2.3 IFC-S Module............................................................................................................. 330
9 Digital Line Equipment............................................................................................................................. 331
9.1 Overview........................................................................................................................ 332
9.2 Transmission Concept..................................................................................................... 333
9.3 Interface X.21................................................................................................................. 334
9.4 Interface G703.1 (64 Kbps)............................................................................................. 335
9.5 Interface G703.6 (2 Mbps HDB3).....................................................................................336
9.6 Jumper Settings.............................................................................................................. 337
10 Copper Line Equipment Module...............................................................................................................339
10.1 Function Description....................................................................................................... 340
10.1.1 Overview...................................................................................................................340
10.1.2 The Receive Section................................................................................................... 341
10.1.3 The Transmit Section................................................................................................. 341
10.1.4 Alarm Displays...........................................................................................................342
10.1.5 S6 Control Wires........................................................................................................ 343
10.1.6 Test Sockets.............................................................................................................. 343
10.1.7 Inhibit Line................................................................................................................ 344
10.2 Connection of an External SWT 3000 to the PowerLink 50/100........................................ 345
Table of Contents
16 Smart Communication, SWT 3000 Teleprotection, Equipment Manual
C53000-G6040-C605-1, Edition 03.2020

11 Fiber Optic Module................................................................................................................................... 347
11.1 Fiber-Optic Module......................................................................................................... 348
11.2 Fiber-Optic Box............................................................................................................... 350
11.2.1 Overview...................................................................................................................350
11.2.2 Interfaces of the FOBox............................................................................................. 350
12 Alarm Module........................................................................................................................................... 353
12.1 Overview........................................................................................................................ 354
12.2 Inputs and Outputs......................................................................................................... 355
12.2.1 Block Diagram........................................................................................................... 355
12.2.2 Binary Inputs............................................................................................................. 355
12.2.3 Relay Outputs............................................................................................................356
12.2.4 Visual Indication........................................................................................................ 356
12.2.5 Test Switch S1........................................................................................................... 356
13 Power Supply............................................................................................................................................359
13.1 Functional Description.................................................................................................... 360
13.1.1 Overview...................................................................................................................360
13.1.2 General Description................................................................................................... 361
13.1.3 Displays.....................................................................................................................362
13.2 Connection of the Power Supply......................................................................................363
13.2.1 Pinout of the Connectors SV-1 and SV-2..................................................................... 363
13.2.2 Redundant Power Supply........................................................................................... 364
13.2.3 Inhibit Loop...............................................................................................................365
14 Technical Data.......................................................................................................................................... 367
14.1 Operating Temperature and Bus Interface....................................................................... 368
14.2 Command Input/Output.................................................................................................. 369
14.3 Transmission Line - Digital Networks............................................................................... 371
14.4 Transmission Line - Fiber-Optic........................................................................................372
14.5 Transmission - Analog Networks......................................................................................374
14.6 Common System Data.....................................................................................................376
14.7 Standards....................................................................................................................... 378
14.8 Electromagnetic Compatibility EMC................................................................................. 379
14.9 Ambient Conditions........................................................................................................ 380
A Appendix.................................................................................................................................................. 381
A.1 Abbreviation List............................................................................................................. 382
Index.........................................................................................................................................................387
Table of Contents
Smart Communication, SWT 3000 Teleprotection, Equipment Manual 17
C53000-G6040-C605-1, Edition 03.2020

18 Smart Communication, SWT 3000 Teleprotection, Equipment Manual
C53000-G6040-C605-1, Edition 03.2020

Safety Instructions
1.1 Scope of Delivery 20
1.2 Transport, Package, Storage 21
1.3 Incoming Inspection 22
1.4 Electrical Inspection 23
1.5 Electrostatic Sensitive Devices 25
1.6 Installation 27
1.7 Replacement 29
1
Smart Communication, SWT 3000 Teleprotection, Equipment Manual 19
C53000-G6040-C605-1, Edition 03.2020

Scope of Delivery
The equipment is delivered with:
•A DVD containing Software for installation and the parametrization of the device and the manuals of
SWT 3000
•The Product Information with a detailed system description and all necessary instructions for installation
and alarm handling
For further details, refer to the attached DVD!
1.1
Safety Instructions
1.1 Scope of Delivery
20 Smart Communication, SWT 3000 Teleprotection, Equipment Manual
C53000-G6040-C605-1, Edition 03.2020