Siemens FIREFINDER-XLS User manual

Siemens Building Technologies
Fire Safety
P/N 315-033874-4
PMI Operation Manual
FIREFINDER-XLS CONTROL PANEL
More
Info
SECURITY
ALARM SUPERVISORY TROUBLE
SILENCED
PARTIAL SYSTEM
DISABLED
AUDIBLES
ON
POWER
?
+
_
....
10:32:05 04/15/01
SYSTEM STATUS: NORMAL
FireFinder-XLS
Siemens - Fire Safety
Technical Manuals Online! - http://www.tech-man.com
firealarmresources.com

Technical Manuals Online! - http://www.tech-man.com
firealarmresources.com

PMI OPERATION MANUAL
CONTENTS i
Contents
INTRODUCTION________________________________________________________________________ 1-1
Interface Overview 1-1
USING THE MENU ______________________________________________________________________ 1-2
Tree Structure 1-5
Physical View 1-5
Geographic View 1-5
Changing Views 1-5
NORMAL MODE _______________________________________________________________________ 1-6
Menu 1-6
ALERT MODE __________________________________________________________________________ 1-6
Alarm 1-7
Supervisory 1-9
Security 1-10
Trouble 1-10
24 Hour Trouble Resound 1-10
Reset Procedures 1-11
REPORT MODE ________________________________________________________________________ 2-1
Configuration Report 2-3
Settings 2-4
Status Report 2-6
Queue Report 2-7
History Report 2-9
MAINTENANCE MODE _________________________________________________________________ 3-1
Control 3-1
Enter Password 3-1
PMI Password Levels 3-2
Time / Date 3-3
Disarm / Arm 3-3
Using The Disarm Feature 3-4
Using The Arm Feature 3-7
ASD 3-9
Change Sensitivity 3-11
History 3-12
Activate / Deactivate 3-14
Technical Manuals Online! - http://www.tech-man.com
firealarmresources.com

PMI OPERATION MANUAL
ii CONTENTS
Walktest 3-16
Suggested Procedure 3-16
Initiating The Walktest 3-17
Walktesting Groups 3-18
Duration And Termination 3-18
Event Annunciation 3-19
Walktest Ending Sequence 3-20
Voice Activations 3-20
Walktest Event Log 3-21
Walktest Reports 3-21
FUNCTION KEYS _______________________________________________________________________ 4-1
LOGOUT _______________________________________________________________________________ 4-1
DIAGNOSTICS _________________________________________________________________________ 4-2
LAMP TEST ____________________________________________________________________________ 4-2
ALTERNATE LANGUAGE ________________________________________________________________ 4-2
Technical Manuals Online! - http://www.tech-man.com
firealarmresources.com

BASIC OPERATION 1-1
INTRODUCTION The PMI is the primary
user interface for the
FireFinder-XLS system.
When the PMI is
installed, the display,
LEDs and control keys/
buttons are visible from
behind a locked door.
Unlock and open the
door to gain access to
those keys and buttons.
From the PMI the
operator can acknowl-
edge events, control the
system notification
appliance circuits and
reset the system. Detailed
information about the nature and location of events can also be displayed.
The PMI contains the site specific program as developed in the Zeus programming
tool. All system logic and supervision is provided by the controller in the PMI.The PMI
and the Zeus programming tool require compatible firmware/software.The tool will
give a warning if the user attempts to use incompatible software to configure a system.
The PMI contains a ¼ VGA monochrome LCD, Touch screen and LEDs for displaying
system status. An audible sounds when there are unacknowledged events on the
PMI. This screen is surrounded by keys that are used to control the displayed informa-
tion and to navigate through these screens. If more items are present than can be
displayed on a single screen, a scroll bar appears to the right of the list. Press the up
and down navigation buttons to the right of the LCD to move through the list.The
selected listing is highlighted in the display. Buttons are also provided to obtain help
and to enter into the menu features of the PMI. See Figure 1-1.
Interface Overview LEDs blink when an event is reported and unacknowledged (ALARM: red,
SUPERVISORY: yellow, SECURITY: yellow,TROUBLE: yellow).The LEDs glow
steady if all events in the class/queue are acknowledged. An internal audible
alarm sounds steady when there is an unacknowledged fire alarm. It pulses if
all alarms are acknowledged, but there is at least one supervisory, trouble or
security condition.
Along the top and bottom of the LCD are rows of four soft keys. These soft keys
have no specific function assigned to them. Each of the soft keys is backlit with a
green triangular LED that is used to guide the operator to the available actions.
Figure 1-1
PMI User Interface
SECURITY
ALARM SUPERVISORY TROUBLE
SILENCED
PARTIAL SYSTEM
DISABLED
AUDIBLES
ON
POWER
?
More
Info
+
_
Alarm(s) # Super(s) # Security(s) # Trouble(s) #
Device custom message
10:53
!
Device custom message
Event Category
Event Category
11:00 (Currently not used)
Device custom message
10:57 (Currently not used)
4
4
4
4
Device custom message
Event Category
11:03 (Currently not used)
Device custom message
Event Category
Acknowledge
Alarms
Silence
Audibles
Unsilence
Audibles
Reset
System
11:06 (Currently not used)










(Currently not used)
....
1
Technical Manuals Online! - http://www.tech-man.com
firealarmresources.com

BASIC OPERATION
PMI OPERATION MANUAL | CHAPTER 1
1-2
POWER - Power LED glows steady green to indicate that the AC power is on;
blinks when the System is on battery backup.
AUDIBLES - Audibles ON or Audibles SILENCED glows steady yellow.
PARTIAL SYSTEM DISABLED - Partial System Disabled glows steady yellow
when any module/device is disabled.
Press
....
to display a MENU of available information.
Scroll UP / Scroll DOWN - Use the scroll up button to navigate up or the scroll
down button to navigate down a list to choose a specific entry from the list of
information displayed on the screen. If the button remains depressed, the list
scrolls progressively faster until it reaches ten items at a time.
MORE INFO (+ / —) - Use More Info/+/- to navigate or drill down (+) or up (—)
through the levels of detail about a selected entry. When viewing a report that is
longer than one screen, pressing (—) highlights the last entry of the report and
pressing (+) highlights the first entry of the report.
HELP - Press ?for context-sensitive help. Press ?again or press the Exit Help
soft key to return to your previous position. If no key presses are made for 60
seconds, the Help will time out and return to the previous screen.
Touch screen display - Touch
selections appear on the screen
when there are options that are
not selectable using the soft
keys. Use of the touch screen is
not required in Alert mode.
The GoTo touch screen (Figure
1-2) is available in the Physical
View for tree navigation and
reports that scroll. Use it to
access information more
quickly by entering the desired address and pressing GoTo, thus eliminating the
need to scroll up or down line by line.
USING THE MENU The menu gives you wide control of the FireFinder-XLS System.You may use the
menu no matter what mode the system is in.
The Main Menu items and the subitems of the Alert, Report and Maintenance
modes are shown in the FireFinder Menu Structure chart that follows. Press
....
to
begin a menu session. The Main Menu items display on the screen. See Figure 1-5.
To enter a menu item, press the soft key pointing to the desired item.
Report
Diagnostics
Alert
Logout
Maint
Lamp Test
Function
Keys
MAIN MENU
Alternate
Language*
Location:
/
:
^
0 1 23 4
56 7 89
_
Bksp Clr Cncl GoTo
Figure 1-2
GoTo Touch Screen
* The alternate language is only visible/present if the Zeus
programming tool has been set for two languages--a base
language and an alternate language.
Technical Manuals Online! - http://www.tech-man.com
firealarmresources.com

BASIC OPERATION
CHAPTER 1 | PMI OPERATION MANUAL
1-3
Use More Info/+ to get:
Event
Acknowledge
ALERT MENU
Silence
Audibles
Unsilence
Audibles
Reset
System
MapDetails Devices
All menu items may not appear, depending upon your System configuration.
Alert Menu
Report Menu
REPORT MENU
Use+or–
to choose level:
Node
Module
Device
Configuration
Status
Queue
History
Supv
Alarm
Security
Trouble
Status SW
Sensitivity
ASD
Threshold
Disarmed
Appl Rev
Category
Base Rev
Usage
Entity Type
Database
Cust Msg
View
Settings
Settings
List
Type
Stop
Time
Start
Time
Clear
Times
All
Node
Module
SubModule
Device
Alarm
Supervisory
Security
Trouble
All Queues
All Non-Events
Print
APPLY
TO
Temperature
*
*
*
*
*
*
*
*
HW Rev
*
FPGA Rev
*
*
*
*
*
*
H-NET
Walktest
*
Settings
Stop
Time
Start
Time
Clear
Times
Cancel
Geographic View
OR
Physical View
GoTo
(Physical
View only)
Location
Technical Manuals Online! - http://www.tech-man.com
firealarmresources.com

BASIC OPERATION
PMI OPERATION MANUAL | CHAPTER 1
1-4
All menu items may not appear, depending upon your System configuration.
Maintenance Menu
Use+or–
to choose level:
Node
Module
Device
Control Enter
Password
Enter
Password
Change
Sens.
Enable
History
Arm
Disarm
Bypass
ASD
Enable
ASD
Clear
History
Change
ASD
Disable
History
Time/
Date:
Disable
Office
Warehouse
Lobby
Computer Rm
Dormitory
Healthcare
Garage
Utility Room
Prec. Storage
Hostile Env.
Duct
Execute
Settings APPLY
TO
Inputs
Outputs
Devices
Smoke/Photo
Switch 1
Switch 2
Thermal
Neural
Relay 1
Relay 2
LED
Status LED
Energized (Disarm Only)
De-Energized (Disarm Only)
Energized (Disarm Only)
De-Energized (Disarm Only)
Execute
Settings APPLY
TO
MAINT MENU
Walktest
All Bells
Group Bells
No Bells
Disable
Settings
Enable/
Extend
APPLY
TO
Cancel
Physical
View
Geographical
View
GoTo Location
Deactivate
Activate
Technical Manuals Online! - http://www.tech-man.com
firealarmresources.com

BASIC OPERATION
CHAPTER 1 | PMI OPERATION MANUAL
1-5
Tree Structure In most menus, the PMI uses a tree structure to display the elements of the system.
Subordinate items connected to a device are children of that device; the device
connected just above the device is its parent.This tree structure closely resembles
the physical arrangement of elements used in the Zeus programming tool.
Devices that have been organized into groups using the Zeus programming tool
appear on the tree structure in the hierarchy of highest to lowest with the corre-
sponding default names of: Campus (L5), Building (L4), Floor (L3), Area (L2), Zone
(L1).The default names can be changed in Zeus.
Devices that are not in groups are considered to be at the “primitive” level.
Physical View The Physical View on the PMI corresponds to the Physical View in the Zeus program-
ming tool.The elements of the system are displayed in tree format. At the highest
level is the system, followed by the modules, submodules and devices. Devices are
children of modules and submodules.The letters PHY on the second line in the upper
left corner of the screen indicate the display is showing the Physical View. (Refer to
Figure 1-3.)
Geographic View The Geographic View on the PMI corresponds to the Geographic View in the Zeus
programming tool. In the Geographic View, elements of the system are displayed in
the groups that were programmed in Zeus. The letters GEO on the second line in the
upper left corner of the screen indicate the display is showing the Geographic View.
This view is used to Disarm/Arm, Walktest, Bypass ASD forTesting and create
reports.
Changing Views To change from the Physical View to the Geographic View, press the Geographic View
soft key (when available).The soft key will then toggle to read Physical View. The
Physical/Geographic View Soft keys appear when the screen shows the tree structure
of the system, as displayed in Figure 1-3.
Configuration Status Queue
10:53 Category text information
Cancel
Geographic View
GoTo
History
Menu:Report
PHY:FireFighter@1, DLC@1
10:53
Category text information
2 ZIC-4A “ZIC-4A at address 2”
3 “ at address 3”ZIC-4A ZIC-4A
4 NIC “Network Interface Card”
5 PSC-12 “Power Supply”
6 RPM “RPM at address 6”
253 PMI-C “Control Panel”
1 DLC “DLC at address 1”
Figure 1-3
PMI Screen DisplayingTree Structure Of System In Physical View
Technical Manuals Online! - http://www.tech-man.com
firealarmresources.com

BASIC OPERATION
PMI OPERATION MANUAL | CHAPTER 1
1-6
NORMAL MODE Normal mode is the absence of any alarm, supervisory, trouble, or security conditions.
The screen displays SYSTEM STATUS: NORMAL with the time and date. If a custom
message has been programmed using the Zeus tool (refer to Zeus Quick Start Guide,
P/N 315-033875), the node custom message also displays in this mode. See Figure 1-4.
CUSTOM MESSAGE
FireFinder - XLS System
10:26:12 07/12/02
SYSTEM STATUS: NORMAL
.
Figure 1-4
Normal Mode Display
The POWER LED glows steady green in Normal mode when the System has AC
power.The ALARM, AUDIBLE ON, AUDIBLE SILENCE, SUPERVISORY, TROUBLE,
SECURITY, and PARTIAL SYSTEM DISABLE LEDs are off and the internal audible is off.
Menu Press the Menu button (see on page 1-2) to display a menu of all PMI options.
See Figure 1-5.The currently available options are described below.
Alert Report Maint
10:53 Category text information
Logout Diagnostics Lamp Test Alt. Language*
Press any lit green arrow key to continue.
Press “?” for more help information.
ALERT: Firefighter’s Mode, view events.
REPORT: View/Print event and system info.
MAINT: Control devices and inputs/outputs.
FUNCTION KEYS: Execute logic commands.
LOGOUT: Leave password protected area.
DIAGNOSTICS: For factory use only.
LAMP TEST: 30 second PMI LED test.
Function Keys
Menu
FireFighter@1
Figure 1-5
PMI Menu Screen
ALERT MODE When an Alarm, Security or Supervisory event occurs in the system, the display
enters the Alert or Firefighter’s mode automatically.The events are displayed in
priority order (Alarm, Supervisory, Security,Trouble), the local audible sounds and the
appropriate LED blinks. If the event caused notification appliances to sound, the
Audibles On indicator lights. At the bottom of the screen an Acknowledge soft key is
displayed. Pressing this key acknowledges the event and silences the local audible.
* The alternate language is only visible/present if the Zeus
programming tool has been set for two languages--a base
language and an alternate language.
Technical Manuals Online! - http://www.tech-man.com
firealarmresources.com

BASIC OPERATION
CHAPTER 1 | PMI OPERATION MANUAL
1-7
Once all events are acknowledged and audibles silenced, a Reset System soft key
becomes available in the lower right side of the display. If notification appliances were
active, two additional soft keys become available at the bottom of the screen.These
allow the operator to silence or unsilence the notification appliances (audibles). When
the notification appliances are silenced the Audibles Silenced LED lights.
Press the More Info/+ button to display a screen showing details relating to the
selected event. Additional soft keys appear at the bottom of this screen, including one
that displays a map of the area in which the event occurred, provided this information
has been programmed using the Zeus tool.The operator can return to the previous
screen by pressing the (-) button, which is adjacent to the More Info/+ button.
Event counts in PMIs and SSDs may differ because SSDs currently display only
“primitive” (individual) events, while a group PMI whose devices are programmed
into groups in Zeus will display only one queue event per group.
Alarm When an alarm is detected, the red Alarm LED blinks, the System’s internal audible
sounds steady, the Audibles On LED glows steady, and the alarm event displays on the
screen with a blinking exclamation mark (!) See Figure 1-6.The event listing displays the
Event Custom Message, theTime of the event occurrence and the Alarm Event
Category (refer to the Alarm Event: Category Cross ReferenceTable.
Alarms 1 Supers 1 Securities 1 Troubles 1
First Floor Reception Area
Alarm Event CATEGORY
10:53 IN
(This Area Currently Not Used)
Acknowledge
Alarms
Silence
Audibles
Unsilence
Audibles
Reset
System
ACTIVE
ACK’D
ALARM
IN
IN
Figure 1-6
Alarm Event Screen
ECNEREFER-SSORCYROGETAC:TNEVEMRALA
yrogetaCeciveDlacisyhP
EKOMSMZH,11-PFH
TAEHtupnI61-MIS,MZH,IRTH,11-TPFH
LAUNAMMZH,tupnI61-MIS,IRTH,SMH
ENOZ.VNOC)enozlanoitnevnocanoegasueciveddeximrof(MZH
WOLFRETAW61-MIS,MZH,IRTH
noitacilppaehtnodesab,srehtorofelbatcelesdnasecivedemosrofdexiferaseirogetaC:ETON
).elbatcelessiIRTHtub,LAUNAMsyawlasiSMH,.e.i(.lootgnimmargorpsueZehtnidetceles
Technical Manuals Online! - http://www.tech-man.com
firealarmresources.com

BASIC OPERATION
PMI OPERATION MANUAL | CHAPTER 1
1-8
In addition, the System responds to alarms with other output functions (as pro-
grammed in the Zeus tool) such as other audible signals.
An Acknowledge Alarms soft key displays in the bottom left corner of the screen.
Press this key to acknowledge each alarm and to silence the local audible.The
blinking exclamation point (!) then changes to a check mark (). See Figure 1-6. (If the
system is programmed as NFPA 72D in the Zeus tool, it is necessary to individually
acknowledge each alarm.)
Highlight an event and press the More info + button to go to the Devices screen, as
shown in Figure 1-7. If the selected item is part of a group, the device list will show
the primitive (individual) devices currently off-normal in the event queue. All events in
a group of the same type (i.e., Alarm, Trouble) display together in the devices screen.
Primitive devices that are not part of a group display by themselves. Depending on
how the system is programmed in Zeus, the top event can be a device or a group.
DETAILS MAP DEVICES BACK
HFP-11@address 3:15
:3-15HFP11 10:56
First Floor Reception Area
Smoke Photoelectric sensor
HFP-11@address 3:16
:3-16HFP11 10:57 Smoke Photoelectric sensor
HFP-11@address 3:17
:3-17HFP11 10:58 Smoke Photoelectric sensor
!
!
WHERE:
First Floor Reception Area is the Group Message
! is an active event; is an acknowledged event
HFP-11 @ address 3:15 is the device custom message
HFP11 is the event device
10:56 is the event time
:3-15 is the event device address
Smoke is the component category
Photoelectric sensor is the event device component
Figure 1-7
Alarm Devices Screen
Pressing the Details soft key takes you to the Details screen as shown in Figure 1-8.
The Details screen contains information that has been entered using the Zeus
programming tool, such as additional information about the alarm location, the
number of devices in alarm (this number can be more than one when the device is
part of a group), the alarm types, the name and phone number of a contact person,
icons showing the fire equipment in the area and icons showing special conditions.
Technical Manuals Online! - http://www.tech-man.com
firealarmresources.com

BASIC OPERATION
CHAPTER 1 | PMI OPERATION MANUAL
1-9
Contact: John Sample
Phone #: [phone]
AREA FIRE EQUIP:
AREA CONTAINS:
DETAILS MAP DEVICES BACK
ALARM LOCATION:
1st Floor Reception Area
- Lobby entrance
# Devices in ALARM: 3
ALARM TYPES:
Smoke, Heat, Flow
First Floor Reception Area
Figure 1-8
Alarm Details Screen
Press the Map soft key to display a map showing the location of the event, provided
the information has been programmed using the Zeus tool. Refer to Figure 1-9. Maps
can be programmed to provide icons showing the event type. These icons are the
same ones that represent Alarm, Security, Supervisory and Trouble on the PMI panel.
The map can also be programmed to show the location of the PMI (“You are here”).
DETAILS
SHOP
LAV HALL
RECEPTION
MAIN STREET
SHIPPING
LOADING DOCK
MAP DEVICES BACK
First Floor Reception Area
Figure 1-9
Sample Map Screen
Supervisory When a supervisory is detected, the yellow Supervisory LED blinks, the System’s
internal audible pulses, and the event(s) display on the screen with a blinking excla-
mation mark (!).This event listing displays the Event Custom Message, the Time of
the event occurrence and the Supervisory Event Category (i.e., Security, Sprinkler,
etc.).
In addition, the System responds to supervisories with other output functions (as
programmed in the Zeus tool).
An Acknowledge Supervisory soft key displays in the bottom left corner of the
screen. Press this key to acknowledge each supervisory and to silence the local
audible.The blinking exclamation point (!) then changes to a check mark (). See
Figure 1-6.
Technical Manuals Online! - http://www.tech-man.com
firealarmresources.com

BASIC OPERATION
PMI OPERATION MANUAL | CHAPTER 1
1-10
Security When a security is detected, the yellow Security LED blinks, the System’s internal
audible pulses, and the event(s) display on the screen with a blinking exclamation
mark (!). This event listing displays the Event Custom Message, the Time of the event
occurrence and the Security Event Category (i.e., Door, Monitor Point, etc.).
In addition, the System responds to securities with other output functions (as
programmed in the Zeus tool).
An Acknowledge Security soft key displays in the bottom left corner of the screen.
Press this key to acknowledge each security and to silence the local audible. The
blinking exclamation point (!) then changes to a check mark (). See Figure 1-6.
Trouble When a trouble is detected, the yellowTrouble LED blinks, the System’s internal
audible pulses, and the event(s) display on the screen with a blinking exclamation
mark (!). This event listing displays the Event Custom Message, the Time of the event
occurrence and theTrouble Event Category (refer to the Trouble Event: Category
Cross Reference Table that follows).
ECNEREFER-SSORCYROGETAC:TNEVEELBUORT
yrogetaCeciveDlacisyhP
ECIVED ,11-TPFH,11-PFH:troperelbuorttiucric/enozroecivedtupnidesivrepusynA
.stiucricdesivrepusyllaudividni61-MIS,MCO,SMH,secivedIRTH
ENOZsenozMZH,senozMAZ,senozCAZ,senozCIZ
ELUDOM .CIN,XSP,CSP,MAZ,CIZ,CLD,IMP,.e.i-elbuorteludomdesivrepusynA
METSYS cificepsaotdetniopniptoneratahtseruliaf/elbuortdetaler-metsySynA
.ecivedroenoz,eludom
KROWTENTENH
.elbatcelesdleiftoneradnayrotcafehtybdenifed-erperaseirogetacesehtfollA:ETON
In addition, the System responds to troubles with other output functions (as pro-
grammed in the Zeus tool).
An Acknowledge Trouble soft key displays in the bottom left corner of the screen.
Press this key to acknowledge each trouble and to silence the local audible. The
blinking exclamation point (!) then changes to a check mark (). See Figure 1-6.
24 Hour Trouble Resound If acknowledged troubles remain in the queue,
the system will sound the local audible every 24
hours as a reminder. A 24 Hour Trouble Resound
pop-up box (See Figure 1-10) will appear on the
PMI and the sounder will remain on until it is
silenced.To silence the local audible, touch any
PMI key or press the Silence button on the
touch screen.
24 Hour Trouble
Resound
Silence
Figure 1-10
24 Hour Trouble Resound Pop-up Box
Technical Manuals Online! - http://www.tech-man.com
firealarmresources.com

BASIC OPERATION
CHAPTER 1 | PMI OPERATION MANUAL
1-11
Reset Procedures There are two types of reset procedures that can be performed on the FireFinder-
XLS System: Hard Reset and Soft Reset.
Hard Reset Other terms for Hard Reset are Power-up, Initialization, and Cold Reset. Applying
power to the system performs a Hard Reset. Doing so initializes the whole system.
What Is Lost:
• Alarm, supervisory, trouble, and security conditions (provided they have
returned to the normal state).
• Arm/disarm.
• Manual sensitivity adjustment.
What Is Not Lost:
• Zeus program.
• Time and date.
• History log.
• Time-based control.
Soft Reset A Soft Reset is performed by pressing the Reset System soft key. The system can
only be reset when all events (alarms, supervisories, securities and troubles) are
acknowledged and the notification appliances are silenced.
What Is Lost:
• Alarm, supervisory, trouble, and security conditions (provided they have
returned to the normal state).
What Is Not Lost:
• Any user entries such as time and date.
• Arm/disarm.
• Zeus program.
• Manual sensitivity adjustment.
• Time-based control.
Technical Manuals Online! - http://www.tech-man.com
firealarmresources.com

BASIC OPERATION
PMI OPERATION MANUAL | CHAPTER 1
1-12
Technical Manuals Online! - http://www.tech-man.com
firealarmresources.com

REPORT MODE Report Mode is used to obtain information and create reports about the system,
modules, submodules and devices.
Report Options There are four options that can be selected in the Report Mode: Configuration,
Status, Queue and History.
Report displays are not dynamic.The information on the PMI screen is displayed at
the moment the report was requested.
The Configuration reports list the following information:
TROPERNOITARUGIFNOC
noitceleSepyTtropeRnoitamrofnItropeR
gsMtsuCegasseMmotsuCsserddAytitnEegasseMmotsuC
esabataDofnIesabataDmetIBDeulaV-----
epyTytitnEepyTytitnEsserddAytitnE-----
egasUegasUeciveDsserddAytitnEegasU
yrogetaCyrogetaCeciveDsserddAytitnEyrogetaC
veRlppAnoisreVnoitacilppA
1
sserddAytitnEnoisreVerawtfoS
veResaBnoisreVesaB
2
sserddAytitnEnoisreVerawmriF
veRWHnoisreVerawdraH
3
sserddAytitnEnoisreVerawdraH
veRAGPFnoisreVAGPF
4
sserddAytitnEnoisreVAGPF
1
cificeps-noitacilppAehtfonoisrevtnerrucehtsevigtroperveRlppAehT
.seoddnasieludomcificepsatahwsenifedtahterawtfoseht,.e.i,erawtfoS
2
ecafretniTENHnommocehtfonoisrevtnerrucehtsevigtroperveResaBehT
.seludomllanoerawmrifesab
3
erawdrahllaotylppatonseodverWH vAN. eriuqcaotelbanurehtiesetacidni
.ytitnemorfelbaliavatonro
4
:ylnoseludombuscificeps-eciovgniwollofehtrofsitroperveRAGPFehT
.BPLdnaCIA,081-MAZ,04-CAZ
REPORT MODE 2-1
2
Technical Manuals Online! - http://www.tech-man.com
firealarmresources.com

PMI OPERATION MANUAL | CHAPTER 2
REPORT MODE2-2
The Status reports list the following information:
TROPERSUTATS
noitceleSepyTtropeRnoitamrofnItropeR
demrasiDdemrasiDsserddAytitnEtnenopmoC
DSADSAsserddAytitnEgnitteSDSA
wSsutatSsehctiwSevitcAsserddAytitnEegasseMmotsuC
ytivitisneSytivitisneSsserddAytitnE)tooF/%(ytivitisneS
dlohserhTdlohserhTsserddAytitnE)tooF/%(dlohserhTmralA
erutarepmeTerutarepmeTsserddAytitnE)CgeD(erutarepmeT
TENHscitsitatSTENHsserddAytitnEscitsitatS
tsetklaWtsetklaWsserddAepyT.gsMmotsuC,etaD/emiT
The Queue reports list the following information:
TROPEREUEUQ
noitceleS tropeR
epyT noitamrofnItropeR
mralAmralAsserddAytitnE motsuC
egasseM
&emiTtnevE
DItnevE TUO/NI
vpuSyrosivrepuSsserddAytitnE motsuC
egasseM
&emiTtnevE
DItnevE TUO/NI
ytiruceSytiruceSsserddAytitnE motsuC
egasseM
&emiTtnevE
DItnevE TUO/NI
elbuorTelbuorTsserddAytitnE motsuC
egasseM
&emiTtnevE
DItnevE
&TUO/NI
epyTelbuorT
Technical Manuals Online! - http://www.tech-man.com
firealarmresources.com

CHAPTER 2 | PMI OPERATION MANUAL
REPORT MODE 2-3
The History reports list the following information:
TROPERYROTSIH
noitceleSepyTtropeRnoitamrofnItropeR
mralAsmralAsserddAepyT tnevE
noitpircseD
emiTtnevE
etaD&
motsuC
egasseM
yrosivrepuSseirosivrepuSsserddAepyT tnevE
noitpircseD
emiTtnevE
etaD&
motsuC
egasseM
ytiruceSseitiruceSsserddAepyT tnevE
noitpircseD
emiTtnevE
etaD&
motsuC
egasseM
elbuorTselbuorTsserddAepyT tnevE
noitpircseD
emiTtnevE
etaD&
motsuC
egasseM
seueuQllA ,vpuS,mrlAllA
stnevElbrT&ceS sserddAepyT tnevE noitpircseD
emiTtnevE
etaD&
motsuC
egasseM
-noNllA
stnevE
yrotsiHrehtOllA
,vpuS,mrlAtoN(
)lbrTroceS
sserddAepyT tnevE
noitpircseD
emiTtnevE
etaD&
motsuC
egasseM
Report Press the Menu button (
....
) on the PMI (upper right) and select the Report option by
pressing the Report soft key.
Press the More Info button on the PMI to navigate to the desired loop or specific
device. When More Info is pressed once it displays the FireFinder-XLS node.
• Press the More Info/+ button again to display a list of FireFinder-XLS
modules; use the up and down buttons to select the desired module.
• Press the More Info/+ button again to display a list of FireFinder-XLS
submodules (provided your system has submodules installed); use the up
and down buttons to select the desired submodule.
• Press the More Info/+ button again to display a list of FireFinder-XLS
devices; use the up and down buttons to select the desired device.
Report - Configuration Once at the desired module/loop or device, press the Configuration soft key to
display all the possible Configuration report types. See Figure 2-1 and the Configura-
tion Report table. “Touch” the desired option to select it and the Report Screen
appears for that option.
Technical Manuals Online! - http://www.tech-man.com
firealarmresources.com

PMI OPERATION MANUAL | CHAPTER 2
REPORT MODE2-4
Category text information
Menu:Report:Configuration
PHY:FireFinder@1
Cancel
Cust Msg Database
Entity Type Usage Category
Appl Rev Base Rev HW Rev FPGA Rev
Figure 2-1
Configuration Report Selections
To access, view and print any of the Configuration Reports, follow the directions
described below. (The Custom Message Report has been used as an example.)
When Cust Msg is selected, the Custom Message Report screen displays as shown
in Figure 2-2.
Menu:Report:Configuration:CustMsg
PHY:FireFinder@1
Custom Message Report
AT: FireFinder@1
Cancel Settings View
SETTINGS:
Module: All
SubModule: All
Device: None
Figure 2-2
Custom Message Report Settings Status
Report - Settings Press the Settings soft key to narrow the focus of the report at the node, module,
submodule and/or device levels. See Figure 2-3.
Choose one from each of the following option levels, then press the Apply soft key:
Node: None / All
Module: None / All / A Specific Module (as programmed in the Zeus Tool)
Submodule: Non / All / A Specific Submodule (as programmed in the Zeus Tool)
Device: None / All / Conv Zone / Manual / Smoke / Thermal /Thermal Only / TRIs
Technical Manuals Online! - http://www.tech-man.com
firealarmresources.com