Siemens OP1S User manual

SIMOVERT MASTERDRIVES
Bedienfeld OP1S
Operator Panel OP1S
Betriebsanleitung
Operating Instructions
Ausgabe / Edition: AA 477 459 4070 76 J AA-74

OP1S Operator Control Panel
Siemens AG 477 459 4070 76 J AA-74
SIMOVERT MASTERDRIVES Operating Instructions
Contents
1 General...............................................................................................................1
2 Connecting, Run-up ..........................................................................................3
2.1 Connecting ..........................................................................................................3
2.2 Run-up.................................................................................................................5
3 Operator control ................................................................................................7
3.1 Operator control elements ...................................................................................7
3.2 Operating display.................................................................................................8
3.3 Basic menu..........................................................................................................9
3.4 Slave ID.............................................................................................................10
3.5 OP: Upread........................................................................................................11
3.6 OP: Download....................................................................................................12
3.7 Delete data........................................................................................................13
3.8 Menu selection ..................................................................................................14
3.8.1 Displaying and correcting parameters................................................................15
3.8.2 Fault and alarm messages ................................................................................20
3.9 Issuing commands via the OP1S.......................................................................21
4 Bus operation ..................................................................................................22
4.1 Configuring slaves.............................................................................................22
4.2 Change slave.....................................................................................................23
5 Technical data..................................................................................................24
Note This operation manual of the OP1S is only valid for MASTER DRIVES
units with the control boards CUVC and CUMC and for MASTER
DRIVES Kompakt+ units.
The usage of the OP1S as spare part for the OP1 in conjunction with
the control boards CU1 (FC), CU2 (VC) and CU3 (SC) is described in
the operation manual of the OP1 with the order No. : 6SE7087-6CX84-
2FF0.

OP1S Operator Control Panel
Siemens AG 477 459 4070 76 J AA-74
SIMOVERT MASTERDRIVES Operating Instructions 1
1 General
The operator control panel (OP1S) is an optional input/output device which can be used
for parameterizing and starting up the units. Plain-text displays greatly facilitate
parameterization.
The OP1S has a non-volatile memory and can permanently store complete sets of
parameters. It can therefore be used for archiving sets of parameters but, first, the
parameter sets must be read out (upread) from the units. Stored parameter sets can also
be transferred (downloaded) to other units.
The OP1S and the units to be operated communicate with each other via a serial
interface (RS485) using the USS protocol. During communication, the OP1S assumes
the function of a master whereas the connected units function as slaves.
The OP1S can be operated at baud rates of 9.6 kBd and 19.2 kBd and is capable of
communicating with up to 32 slaves (addresses 0 to 31). It can therefore be used in a
point-to-point link (e.g. during initial parameterization) or within a bus configuration.
The plain-text displays can be shown in one of five different languages (German, English,
Spanish, French, Italian). The language is chosen by selecting the relevant parameter for
the slave in question.
Order numbers
Components Order No.
OP1S 6SE7090-0XX84-2FK0
Connecting cable 3 m 6SX7010-0AB03
Connecting cable 5 m 6SX7010-0AB05
Adapter for installation in cabinet door, incl. 5 m cable 6SX7010-0AA00
NOTE The parameter settings for units connected to the OP1S are given in the
corresponding documentation (Compendium).

OP1S Operator Control Panel
477 459 4070 76 J AA-74 Siemens AG
2Operating Instructions SIMOVERT MASTERDRIVES
Inching key
OFF key
ON key
Key for toggling between control levels
Lower key
Raise key
Reversing key
8.2 A 25 V 00
# 100.000 min-1
* 100.000 min-1
Run
LCD (4 lines x 16 characters)
Sign key
Reset key
0 to 9: number keys
Jog789
P
Reset
+/-
0
456
123
O
I
Fault
Run
9-pole SUB-D connector
on rear of unit
LED green
LED red
Fig. 1-1 View of the OP1S
OP1S connection
Pin Designation Meaning Range
3 RS485 P Data via RS485 interface
5 M5V Ground
6 P5V 5 V aux. voltage supply ±5 %, 200 mA
8 RS485 N Data via RS485 interface
9 Reference potential
Table 1-1 Connections of the OP1S
15
69

OP1S Operator Control Panel
Siemens AG 477 459 4070 76 J AA-74
SIMOVERT MASTERDRIVES Operating Instructions 3
2 Connecting, Run-up
2.1 Connecting
The OP1S can be connected to the units in the following ways:
♦ Connection via 3 m or 5 m cable (e.g. as a manual input device for start-up)
♦ Connection via cable and adapter for installation in cabinet door
♦ Direct plugging into the units provided for it, e.g. MASTERDRIVE Compact units or
the Compact PLUS MASTERDRIVE rectifier unit.
Connection via cable
SIEMENS
A
S1
BX101
CX103
P
USS-Bus
100.0A 380 .0V 00
#-300.000H z
*-300.000Hz
Betrieb
Jog 7 8 9
P
Reset
+/-0
456
123
O
I
Fault
Run
OP1S
USSviaRS485
5
4
3
2
1
9
8
7
6
5
4
3
2
1
9
8
7
6
OP1S side:
9-pole SUB-D socket
Unit side:
9-pole SUB-D connector
Connecting cable
Fig. 2-1 Example: The OP1S in a point-to-point link with the Compact PLUS unit

OP1S Operator Control Panel
477 459 4070 76 J AA-74 Siemens AG
4Operating Instructions SIMOVERT MASTERDRIVES
Plugging into the units provided
USS-Bus
100. 0A 380.0V 00
#-30 0.000H z
*-30 0.000Hz
Betr ieb
Jog 7 8 9
P
Reset
+/-0
456
123
O
I
Fault
Run
SIEMENS SIEMENS
X100
Run
Failure
Chopper
activ e
SIEMENS
A
S1
BX101
CX103
CM Rect.Unit Inv.
USS bus
on X100
OP1S mounted
on rectifier unit
SIEMENS
A
S1
BX101
CX103
Inv.
SIEMENS
A
S1
BX101
CX103
SIEMENS
A
S1
BX101
CX103
Inv. Inv.
Fig. 2-2 Example: The OP1S during bus operation with Compact PLUS units
NOTE During bus operation, the Compact PLUS rectifier unit is only for
mechanically restraining the OP1S and for connecting the bus to the
inverters. It does not function as a slave.

OP1S Operator Control Panel
Siemens AG 477 459 4070 76 J AA-74
SIMOVERT MASTERDRIVES Operating Instructions 5
2.2 Run-up
After the power supply for the unit connected to the OP1S has been turned on or after
the OP1S has been plugged into a unit which is operating, there is a run-up phase.
!CAUTION The OP1S must not be plugged into the Sub-D socket if the
SCom1 interface parallel to the socket is already being used
elsewhere, e.g. bus operation with SIMATIC as the master.
NOTE In the as-delivered state or after a reset of the parameters to the factory
setting with the unit’s own control panel, a point-to-point link can be adopted
with the OP1S without any further preparatory measures.
When a bus system is started up with the OP1S, the slaves must first be
configured individually. The plugs of the bus cable must be removed for this
purpose (see section "Bus operation").
During the run-up phase, the text "Search slave" is shown in the first line of the display,
followed by "Slave found" and the found slave number as well as the set baud rate.
Slave found
Address: [00]
Baud rate: [6]
Example of a display after the run-up
phase (6 corresponds to 9.6 kBd)
After approximately 4 s, the display changes to
SIEMENS
MASTERDRIVES MC
6SE7014-0TP50
SW:V1.0 OP:V2T20
Example of what is displayed after a
slave address has been found

OP1S Operator Control Panel
477 459 4070 76 J AA-74 Siemens AG
6Operating Instructions SIMOVERT MASTERDRIVES
After a further 2 s, there is a changeover to the operating display. If it is not possible to
start communicating with the slave, an error message "Error: Configuration not ok"
appears. About 2 s later, a request is made for new configuration.
New config?
#yes
no
Error message displayed when
communication not possible
If the "P" key is pressed, the connected unit is reconfigured, i.e. the interface parameters
are set to the standard values.
Number of PKWs: 127
Number of PZDs: 2 or 4
Telegram failure time: 0 ms
If communication with the slave is still impossible, the reasons may be as follows:
♦ Defective cabling
♦ Bus operation with two or more slaves with the same bus address (see section "Bus
operation").
♦ The baud rate set in the slave is neither 9.6 nor 19.2 kBd.
In the latter case, an error message appears: "Error: No Slave found". The unit’s own
control panel must then be used to set the baud rate to 9.6/19.2 kBd or to reset the
parameters to the factory setting.

OP1S Operator Control Panel
Siemens AG 477 459 4070 76 J AA-74
SIMOVERT MASTERDRIVES Operating Instructions 7
3 Operator control
3.1 Operator control elements
Key Meaning Function
ON key • For energizing the drive (enabling motor activation). This
function must be enabled by means of parameterization.
OFF key • For de-energizing the drive by means of OFF1, OFF2 or
OFF3, depending on parameterization. This function must
be enabled by means of parameterization.
Jog key • For jogging with jog setpoint 1 (only effective when the unit
is in the "ready to start" state). This function must be
enabled by means of parameterization.
Reversing
key • For reversing the direction of rotation of the drive. This
function must be enabled by means of parameterization.
Toggle key • For selecting menu levels and switching between
parameter number, parameter index and parameter value
in the sequence indicated. The current level is displayed by
the position of the cursor on the LCD display (the
command comes into effect when the key is released).
• For concluding a numerical input
Reset Reset key • For leaving menu levels
• If fault display active, this is for acknowledging the fault.
This function must be enabled by means of
parameterization.
Raise key For increasing the displayed value
• Short press = single-step increase
• Long press = rapid increase
• If motor potentiometer is active, this is for raising the
setpoint. This function must be enabled by means of
parameterization.
Lower key For lowering the displayed value
• Short press = single-step decrease
• Long-press = rapid decrease
• If motor potentiometer is active, this is for lowering the
setpoint. This function must be enabled by means of
parameterization.

OP1S Operator Control Panel
477 459 4070 76 J AA-74 Siemens AG
8Operating Instructions SIMOVERT MASTERDRIVES
Key Meaning Function
+/- Sign key • For changing the sign so that negative values can be
entered
0... 9Number keys • Numerical input
Table 3-1 Operator control elements of the OP1S
3.2 Operating display
After run-up of the OP1S, the following operating display appears.
0.0 A 0 V 00
# 0.00 min-1
* 0.00 min-1
Ready
Example of an operating display in
the "Ready" state
The values shown in the operating display (except for slave number, 1st line on the far
right) can be specified by means of parameterization.
1st line left in the example "Output current"
1st line right in the example "DC link voltage"
2nd line actual value in the example, "Actual speed" (only a visualization
parameter)
3rd line setpoint in the example "Speed setpoint"
4th line in the example "Operating state"
In the operating display, the actual value is indicated with "#“ and the setpoint with "*“.
In addition to the operating display on the display unit, the operating state is indicated by
the red and green LEDs as follows:
Flashing Continuous
Red LED Warning Fault
Green LED Ready Operating
Table 3-2 Operating displays