Siemens FS-TRI-M User manual

SiemensBuilding Technologies, Inc.
FlorhamPark, New Jersey 07932
RED BLK ORG ORG GRN
EARTH
GND
TOCONTROL PANEL
ORPREVIOUS ADDRESSABLE DEVICE
+-
MODEL: FS-TRI-M
REFER TO INSTL. INSTR.
P/N 315-699487
DEVICE ADDR.__________
ALLTERMINALS ARE POWERLIMITED
NOTE:
DO NOT USE
REAR CONDUIT ENTRY
SINGLE GANG
SWITCHBOX
(USER SUPPLIED)
SINGLE GANG
SWITCHPLATE (BLANK)
(USER SUPPLIED)
FS-TRI-M
U
L
UNDERWRITERS
LABORATORIES
The SIEMENS FS-TRI-M Contact Monitoring Module,
as shown in Figure 1, interfaces normally open contact
devices to an ddressable Device Circuit of a fire
alarm control unit.
The FS-TRI-M supports Style B (Class B) Initiating
Device Circuit wiring. Each module uses one address
on the ddressable Device Circuit. It does not require
any mechanical address programming. Use the FS-FPI
Programmer/Tester to program and test the module.
PROGRAMMING INSTRUCTIONS
CAUTION:
1. To prevent damage to the FS-FPI, do not
connect module to the FS-FPI until the
Addre able Device Circuit wiring i
di connected.
2. Only one device mu t be connected to the
FS-FPI at a time.
1. Connect the red and black wires of the FS-TRI-M
to the SIEMENS FS-FPI Programmer/Tester. Use
the cable provided with the Programmer/Tester
and the 2 alligator clips provided.
2. Set the address for the module by following the
instructions in the FS-FPI Programmer/Tester
Manual (P/N 315-699480).
3. Record the device address on the label located
on the module. The module can now be installed
and wired to the system.
MOUNTING
The FS-TRI-M mu t be in talled in a
UL Li ted electrical box.
Refer to Figure 2.
1. Connect the appropriate wires using wire nuts.
Tuck the FS-TRI-M module inside the electrical
box and dress the wiring as required.
2. Fasten the cover plate (user supplied) to the box.
Figure 2
FS-TRI-M Mounting
P/N 315-699487-1
Siemens Building Technologies, Inc.
8 ernwood Road
lorham Park, New Jersey 07932
Siemens Building Technologies, Ltd.
2 Kenview Boulevard
Brampton, Ontario L6T 5E4 CN
Installation Instructions
Models FS-TRI-M
Contact Monitoring Module
Fire Safety
Figure 1
FS-TRI-M Module

Figure 3
FS-TRI-M Wiring
NOTES:
1. ll circuits are power limited.
2. In supervisory:
FS-TRI-M draws 1.5m
3. Initiating Device Circuit ratings:
Style B, Class B
See NFP 72 standard for the number of normally open contact devices allowed.
Voltage (max.): 5 VDC (during polling)
Supervisory current (max.): 0.5m (during polling)
larm current (max.): 0.8m (during polling)
IDC cable requirements:
Wire size: 18 to 14 WG
Wire resistance (max.): 2 ohms
Cable length (max.): 200 feet
Cable Type: Data grade, twisted pair
4. If Earth Ground is available, the green wire should be connected to earth ground.
5. If Earth Ground is NOT available, the IDC wiring should be limited to the same room.
RED
BLACK
GREEN
ORANGE
ORANGE
FS-TRI-M
+
+
-
-TO NEXT
ADDRESSABLE DEVICE
FROM ADDRESSABLE DEVICE
CIRCUIT OF A COMPATIBLE
CONTROL UNIT OR PREVIOUS
ADDRESSABLE DEVICE
GROUND
SEE NOTES 4 AND 5
END OF LINE RESISTOR
P/N 140-820185
3.6K, 1/4W, 5%
CONTACT DEVICE
INITIATING DEVICE CIRCUIT
SUPERVISED, SEE NOTE 3
ADDRESSABLE DEVICE CIRCUIT
24VDC NOMINAL, SUPERVISED
WIRING
Remove all y tem power before in tallation, fir t battery and then AC.
(To power up, connect AC first then battery.)
Refer to the wiring diagram and wire the module accordingly.
P/N 315-699487-1