Siemens SIM-16RC User manual

SiemensSiemens
SiemensSiemens
Siemens IndustryIndustry
IndustryIndustry
Industry,,
,,
,Inc.Inc.
Inc.Inc.
Inc.
BuildingBuilding
BuildingBuilding
Building
TT
TT
Tecec
ecec
echnologies Dihnologies Di
hnologies Dihnologies Di
hnologies Divisionvision
visionvision
vision
P/N 315-050715-1
Supervised Input Module Ribbon Cable
Installation Instructions
Model SIM-16RC
INTRODUCTION The Model SIM-16RC Supervised Input Module Ribbon
Cable from Siemens Industry, Inc., is a remotely located,
general purpose input module. It provides sixteen input
circuits for remote system monitoring. Each input can
only be unsupervised (general-purpose input). The
SIM-16RC has two Form C relays.The relays and the
inputs are programmed by inserting an SIM-16 in the
Zeus Programming Tool.
Inputs must be programmed as unsupervised.
OPERATION The SIM-16RC is mounted in an enclosure that is
remotely located from the Main Panel. Communication
between the SIM-16RC and the NIC-C (Network Interface
Card) or DAC-NET is through the Control Area Network
(CAN) bus. Up to 99 SIM-16RCs can be used with a
single NIC-C or DAC-NET.
Each SIM-16RC has two 10-position rotary switches that
are used to set the board address on the CAN which is a
sub-address of the NIC-C or DAC-NET.
Every time a change of state of the input is detected, a
unique CAN message is sent to the NIC-C or DAC-NET. A
CAN message from the NIC-C or DAC-NET directed to
the SIM-16RC controls the Form C relays.
PRE-INSTALLATION Rotary Address Switches - Set the board address for
each SIM-16RC using both of the ten-position rotary
switches located on the board (See Figure 1). Each of
these addresses must be a sub-address of the NIC-C or
DAC-NET and must be the same as the addresses
assigned in the Zeus Programming Tool.
INSTALLATION A SIM-16RC may be installed in a REMBOX. When using REMBOX 2 or 4, mount the
SIM-16RC in one module space on a REMBOX2-MP, P/N 500-634211 or REMBOX4-
MP, P/N 500-634212 using the four screws provided. (Refer to REMBOX2-MP/
REMBOX4-MP Installation Instructions, P/N 315-034211.) Up to 4 SIM-16RCs will fit
in a REMBOX2; up to 8 SIM-16RCs will fit in a REMBOX4.
Figure 1
SIM-16RC Supervised
Input Module Ribbon
Cable
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
0
P2
S1 S2
P3
TB3
1
1
6
6
TB4
SIM-16RC
16
15
2
1
J1
1
2
15
16
J2

Siemens Industry, Inc.
Building Technologies Division
P/N 315-050715-12
WIRING Refer to Figures 2-5.
Remove all system power before installation, first battery then AC. (To power up,
connect the AC first, then the battery.)
• Each SIM-16RC module is a node in the CAN bus.
• The SIM-16RC can be installed with or without an RNI. Connect the CAN
bus and 24V as shown in Figures 2 and 3.
• Up to 99 CAN modules, in any combination, can be connected to the CAN
bus of each NIC-C or DAC-NET.
• Each SIM-16RC module is shipped with one CCS cable.
• Cable connections for SIM-16RC modules are shown in the following table:
SNOITCENNOCELBACCR61-MIS
elbaCnoitpircseDrebmuNtraPnoitcennoC
LCCgnoL-ELBAC-NAC rotcudnoc-6,.ni03 412436-995.C
R61-MIStsrifotINRno4PstcennoC /MCFotCR61-MISmorfstcennocoslA .)roodno(seludomBSC/MCS/MCL
SCCtrohS-ELBAC-N
AC rotcudnoc-6,.ni½5 935331-555-MISotseludomCR61-MISstcennoC 61-MCOroCR61-MCO,61-MIS,CR61 worelgnisaniselu
dom
The CAN bus requires a 120Stermination at each end of the loop. Refer to the NIC-C
Installation Instructions, P/N 315-033240 for details about CAN termination.
The ribbon cable for J1 and J2 is to be provided with the external unit.
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
0
P2
S1 S2
P3
TB3
1
1
6
6
TB4
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
0
P2
S1 S2
P3
TB3
1
1
6
6
TB4
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
0
P2
S1 S2
P3
TB3
1
1
6
6
TB4
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
0
P2
S1 S2
P3
TB3
1
1
6
6
TB4
TO RNI, P4
CAN TERMINATOR,
P/N 110-134215
(SHIPPED WITH NIC-C)
CABLE
MODEL
# CCS
CABLE
MODEL
# CCL
SIM-16RC SIM-16RC SIM-16RC SIM-16RC
16
15
2
1
J1
1
2
15
16
J2
1
2
15
16
J2
1
2
15
16
J2
1
2
15
16
J2
16
15
2
1
J1
16
15
2
1
J1
16
15
2
1
J1
Figure 2
SIM-16RC CAN Bus Connections With An RNI

Siemens Industry, Inc.
Building Technologies Division
P/N 315-050715-13
Figure 3
SIM-16RC Wiring Without An RNI
NOTES
1. All wiring supervised.
2. All circuits are power limited
per article 760 of NEC.
3. The ribbon cables for J1 and
J2 must be:
- within the same room
- within 20 ft.
- in rigid conduit.
4. Wiring forTB3 and TB4 is
18AWG min., 16 AWG max.
5. CAN network max. line
resistance 15S.
6. Refer to the NIC-C
Installation Instructions, P/N
315-033240 for CAN
network termination
instructions.
Figure 4
SIM-16RC Relay Connections
NOTES
1. Contacts are unsupervised.
2. 1A max @ 24VDC resistive.
3. All wiring must remain
inside the enclosure or
within 20 feet in rigid
conduit.
4. The ribbon cables for J1 and
J2 must be:
- within the same room
- within 20 ft.
- in rigid conduit.
5. Wiring forTB3 and TB4 is
18AWG min., 16 AWG max.
SIM-16RC
CAN –
SHIELD
SHIELD
24 V RET
+24 V
CAN +
TB3
TO PSC-12/PSX-12, TB3
OR ANY REGULATED
POWER LIMITED POWER
SUPPLY LISTED FOR
FIRE PROTECTIVE
SIGNALING USE
TO PSC-12, TB1
SEE NIC-C
INSTALLATION
INSTRUCTIONS,
P/N 315-033240
FOR WIRING DETAILS
1
2
15
16
J2
6
5
4
3
2
1
COM
N.C.
N.O.
COM
N.C.
N.O.
Programmable
Relay 2
Programmable
Relay 1
TB3
1
6
TB4
SIM-16RC
1
2
15
16
J2

Siemens Industry, Inc.
Building Technologies Division
Florham Park, NJ
Siemens Canada Limited
Building Technologies Division
2 Kenview Boulevard
Brampton, Ontario L6T 5E4 Canada P/N 315-050715-1
Figure 5
SIM-16RC Unsupervised Input Wiring
NOTES
1. All inputs unsupervised.
2. All inputs are power limited
per article 760 of NEC.
3. The ribbon cables for J1 and
J2 must be:
- within the same room
- within 20 ft.
- in rigid conduit.
4. All inputs must remain
inside the enclosure or
within 20 feet in rigid
conduit.
5. In the Zeus Programming
Tool, select unsupervised for
each unsupervised input.
6. Inputs #1 - 16 are program-
mable.
SIM-16RC
TYPICAL
CONNECTION
(16 PLACES)
INPUT #2
INPUT #1
INPUT #6
INPUT #16
INPUT #5
INPUT #9
1
2
15
16
J2
16
15
2
1
J1
ELECTRICAL RATINGS
tnerruCenalPkcaBV420
tnerruCV42lanimreTwercS Am02 tupnidesivrepus/Am2.1+ yalerevitca/Am02+
tnerruCenalPkcaB
V2.60
tnerruCybdnatSV42 Am02 tupnidesivrepus/Am2.1+ yalerevitca/Am02+
rewoPtuptuO
riaPkrowteNNAC .xamkaepotka
epV8
.xamAm57 )noissimsnartgsmgnirud(