Siemens SIPROTEC4 7SJ61 User manual

SIPROTEC4
Multifunction protection with
control
7SJ61 / 7SJ62 / 7SJ63
6MD63
Communication module
DNP 3.0
Communication Database and
Device Profile Document
Bus mapping
Revision: 1.0
Edition: June 2000
C53000-L1840-A001-01
Preface
Overview 1
Parametrization in DIGSI 2
DNP V3.00 Device Profile 3
Communication-Interfaces 4
Glossary
Index
Cover

Non-liability clause Copyright
Although we have checked the contents of this publication for
conformance with the hardware and software described we
cannot guarantee complete conformance since differences
cannot be ruled out.
The information in this manual is checked at regular intervals,
and necessary corrections are included in the next releases.
Your suggestions are welcome.
Subject to change without prior notice.
Copyright © Siemens AG 2000. All rights reserved.
Passing on or reproduction of this document, utilization and revelation
of its contents is not permitted without express permission.
Violations shall be cause for damage claims.
All rights reserved, in particular when a patent is issued or a general
model registered.
Registered trademarks
SIPROTEC® und DIGSI® are registered trademarks of Siemens AG.
Other designations in this manual may be trademarks that if used by
third parties for their own purposes may violate the rights of the owner.
Siemens Aktiengesellschaft C53000-L1840-A001-01

7SJ61/62/63 6MD63 DNP3.0 Device Profile Document
C53000-L1840-A001-01 i
Preface
Contents of this
manual The manual is devided into the following topics:
•Overview
•Parametrization in DIGSI
•DNP V3.00 Device Profile
•Communication-Interfaces
Additional
literature This manual describes the data in the DNP messages standard mapping
of the SIPROTEC devices.
The following additional manuals inform you about the function,
operation, assembly and commissioning of the SIPROTEC devices:
Manual Contents Order number
Overcurrent, overload
and motor protection with
control
SIPROTEC 7SJ61
Function, operation, assembly
and commissioning of the
SIPROTEC device 7SJ61
C53000-G1140-C118-2
Multifunction protection
with control
SIPROTEC 7SJ62
Function, operation, assembly
and commissioning of the
SIPROTEC device 7SJ62
C53000-G1140-C121-2
Multifunction protection
with control
SIPROTEC 7SJ63
Function, operation, assembly
and commissioning of the
SIPROTEC device 7SJ63
C53000-G1140-C120-2
Input/output unit with
local control
SIPROTEC 6MD63
Function, operation, assembly
and commissioning of the
SIPROTEC device 6MD63
C53000-C1840-C101-2

Preface
7SJ61/62/63 6MD63 DNP3.0 Device Profile Document
C53000-L1840-A001-01
ii
The DNP V3.0 specification and the structure of the DNP messages are
defined in:
ØDNP V3.00 Subset Definitions
Edition 2.00, November 1995
DNP Users Group
Document Nr.: P009-OIG.SUB
ØDNP V3.00 Data Object Library
Edition 0.02, July 1997
DNP Users Group
Document Nr.: P009-OBL
ØDNP V3.00 Data Link Layer
Edition 0.02, May 1997
DNP Users Group
Document Nr.: P009-OPD.DL
ØDNP V3.00 Application Layer
Edition 0.03, May 1997
DNP Users Group
Document Nr.: P009-OPD.APP
ØDNP V3.00 Transport Functions
Edition 0.01, May 1997
DNP Users Group
Document Nr.: P009-OPD.TF
Notes to this
manual This manual provides you with the following aids to make it easier to
locate the information you are looking for:
•At the beginning of this manual you will find a complete table of
contents plus separate lists of figures and tables contained in this
manual.
•In the individual chapters, you will find information in the left margin
of each page which will give you an overview of the contents of that
particular paragraph.
•Following the last chapter of this manual, you will find a glossary
containing definitions of technical terms and abbreviations used in
this manual.
•At the end of this manual, you will find a comprehensive index for
fast access to the information you need.
Validity This manual is valid for
•SIPROTEC devices 7SJ61, 7SJ62, 7SJ63 and 6MD63 with firmware
version 4.2 and DNP communication module.
Training courses See our catalog of courses for a list of available courses or contact our
training center in Nuremberg.
Questions If you have questions to the SIPROTEC devices, contact your Siemens
representative.

7SJ61/62/63 6MD63 DNP3.0 Device Profile Document
C53000-L1840-A001-01 iii
Revision index
Modified chapters /
pages Edition Reasons of modification
1.0 First edition
June 8th, 2000

Revision index
7SJ61/62/63 6MD63 DNP3.0 Device Profile Document
C53000-L1840-A001-01
iv

7SJ61/62/63 6MD63 DNP3.0 Device Profile Document
C53000-L1840-A001-01 v
Table of contents
1 Overview......................................................................................................................... 1-1
2 Parametrization in DIGSI............................................................................................... 2-1
3 DNP V3.00 Device Profile .............................................................................................. 3-1
3.1 Implementation Table................................................................................................ 3-1
3.2 Device Profile Document........................................................................................... 3-3
3.3 Binary Input Points .................................................................................................... 3-6
Automatic reclosure status.................................................................................. 3-6
Time Overcurrent protection ............................................................................... 3-6
InRush Function.................................................................................................. 3-8
Directional time overcurrent protection ............................................................... 3-8
Unbalanced load protection............................................................................... 3-10
Frequency protection......................................................................................... 3-10
Voltage protection ............................................................................................. 3-11
Command Mode Information............................................................................. 3-11
Internal Mode Status......................................................................................... 3-12
Highly sensitive earth fault protection................................................................ 3-13
Circuit breaker failure protection ....................................................................... 3-14
Thermal overload protection ............................................................................. 3-15
Monitor start protection...................................................................................... 3-15
Start-up supervision .......................................................................................... 3-15
Trip coil monitor................................................................................................. 3-15
Extension........................................................................................................... 3-16
Control switches return position indication(double point commands)............... 3-16
Internal controls................................................................................................. 3-16
Output channels return position indication (Single point commands)............... 3-17
Input channels................................................................................................... 3-17
CFC Output....................................................................................................... 3-19
3.4 Control Relay Output Blocks/Binary Output Status(mapping 1 and 2).................... 3-20
External commands (Double point commands)................................................ 3-20
Internal commands............................................................................................ 3-21
Output channel (user defined single point output commands).......................... 3-21
CFC Input.......................................................................................................... 3-22
3.5 Control Relay Output Blocks/Binary Output Status(mapping 3 and 4).................... 3-24
External commands (Double point commands)................................................ 3-24
3.6 Counters.................................................................................................................. 3-26
3.7 Analog Inputs........................................................................................................... 3-27

Table of contents
7SJ61/62/63 6MD63 DNP3.0 Device Profile Document
C53000-L1840-A001-01
vi
4 Communication-Interfaces............................................................................................ 4-1
4.1 Technical Data RS485 modul....................................................................................4-1
4.2 Technical Data Fiber Optical Link modul...................................................................4-2
5 Glossary.......................................................................................................................... 5-1
6 Index................................................................................................................................ 6-1

7SJ61/62/63 6MD63 DNP3.0 Device Profile Document
C53000-L1840-A001-01 1-1
1 Overview
Overview 1
Mapping: This document describes the DNP standard mapping for SIPROTEC4
devices.
•Standard mapping one specifies the analog values for the voltage
range of 32.767 kV and two DNP index points for double point
commands.
•Standard mapping two specifies the analog values for the voltage
range of 327.67 kV and two DNP index points for double point
commands.
•Standard mapping three specifies the analog values for the voltage
range of 32.767 kV and one DNP index point for double point
commands.
•Standard mapping four specifies the analog values for the voltage
range of 327.67 kV and one DNP index point for double point
commands.
The following functions, described within the instruction book of
the 7SJ61/62/63 and 6MD63 for some protocols, are not available
via DNP 3.00.
Function Remedy
Oscillographic wave form
capture Redundant service port via modem or direct connection for DIGSI 4
Remote settings Redundant service port via modem
or direct connection for DIGSI 4
Additional information points map “User defined channels” via
CFC
Additional control
command/devices (Be careful:
Don’t delete or rename the
predefined control devices. The
user can not recreate control
command/devices after deleting
or renaming them within the
matrix)
If accidentally deleted or renamed,
do not save the setting changes or
create a new device within the DIGSI
manager. You must reprogram the
entire relay after creating a new
device.
Time synchronization Use IRIG B input
Block Data Transmission None
Generate Indications None

Overview
7SJ61/62/63 6MD63 DNP3.0 Device Profile Document
C53000-L1840-A001-01
1-2
Specifications The communication database profile in the SIPROTEC-device 7SJ61-63
and 6MD63 with the DNP3.0 protocol is grouped into twelve object
types. These are:
•Binary Input with Status (object 01, variation 02):
These points represents the state of a digital input-channel or an
internal software-information-point. It is used for a general
interrogation request by a RTU (after a reset or cyclic during
runtime) to synchronize the RTU information-database. They are
considered class 1 data (an event with high priority).
•Binary Input Change with Time (object 02, variation 02):
These points represents the changed state of a digital input-
channel or an internal software-information-point and the time at
which the state changed. It is used for spontaneous process-
events. They are considered class 1 data (an event with high
priority). It is used for spontaneous process-events. They are
considered class 1 data (an event with high priority).
•Binary Output Status (object 10, variation 02):
These points represents the current status of a controlled digital
output-channel. These digital output-channels are controlled by
the Control Relay Output Block (object 12).
•Control Relay Output Block (Direct Operate) (object 12, variation
01):
These points are used for commands to the process or setting
internal functions.
•32-Bit Binary Counter (with Flag) (object 20, variation 01):
These points are used to represent a counter for active and
reactive Power.
•32-Bit Counter Change Event without Time (object 22, variation
01):
These points are used to represent a counter for active and
reactive Power reported as an event.
•16-Bit Analog Input (Measurements) (object 30, variation 02):
These points are used to represent an actual analog point. This
16-bit signed value could represent a digitized signal or calculated
value. It is used for a General Interrogation Functionality within the
startup-procedure or for an Measurement snapshot.
•16-Bit Analog Change Event without Time (Measurements)
(object 32, variation 02):
These points are used to represent a changed analog point. The
time of measurement-change is determined from the
measurement-filter-method.
•16-Bit Analog Change Event with Time (Measurements) (object
32, variation 04):
These points are used to represent current and voltage minimum
and maximum values. The time stamp represent the last value
updating.

7SJ61/62/63 6MD63 DNP3.0 Device Profile Document
C53000-L1840-A001-01 1-3
•Time and Date (object 50, variation 01):
The time and date object is an information object that represents
the absolute time of day and date. This object are used for time-
synchronization. The absolute time is recorded as milliseconds
since midnight, January 1st, 1970, at zero hours, zero minutes,
zero seconds and milliseconds.
•Class Data (object 60, variation 01, 02, 03, 04):
This objects specifies different classes of information elements.
Class 0 specifies any information objects not assigned to class 1
until class 3.
Classes 1 to 3 specifies groups of event driven information
objects. Class 1 data has higher priority than class 2 , class 3 and
static data.
•Internal Indications (object 80, variation 01):
This object reflect internal status of device. This are availability of
class 1,2,3 date, device trouble and so on.
Response time Some approximate response times with different numbers of selected
points at 9600 baud are:
1 point à70 milliseconds
30 points à115 milliseconds
376 points à670 milliseconds

Overview
7SJ61/62/63 6MD63 DNP3.0 Device Profile Document
C53000-L1840-A001-01
1-4

Parametrization in DIGSI
7SJ61/62/63 6MD63 DNP3.0 Device Profile Document
C53000-L1840-A001-01 2-1
2 Parametrization in DIGSI
Parametrization in DIGSI 2
The SIPROTEC-device is designed so that the users can select only the
group of data points in which they are interested. Users can select
mappings by the protection data processing program DIGSI®. Within the
DIGSI Manager àProperties of SIPROTEC 4 device àthe user may
choose the data mapping of choice.
An Edit area will be active after selecting the mapping file. Device
specific data, like “slave address” and DNP specific parameter can be
edited.

Parametrization in DIGSI
7SJ61/62/63 6MD63 DNP3.0 Device Profile Document
C53000-L1840-A001-01
2-2
Edit only the numbers. Editing anything else will cause unexpected
problems.
Only those SIPROTEC objects can transmitted or controlled by DNP
which are listed in the DNP V3.00 Device Profile
All these objects are already contained in the standard parameter set
and they can identified by their name or their „Internal object no.“ (not all
SIPROTEC objects have an internal object number).
Information points Control commands can be found within the matrix within the group
“Control device” or “Protocol”. “User defined information” can be found
within the matrix within the group “Protocol”
For transmission of installation-specific commands and annunciations
user-definable objects are available.
Binary outputs and binary inputs of the SIPROTEC device can be
assigned to these objects using the DIGSI parameterization software.
CFC-Incoming annunciations and CFC-Output indications can be used
to allocate protection annunciations, which are not containd in the
standard mapping of DNP

Parametrization in DIGSI
7SJ61/62/63 6MD63 DNP3.0 Device Profile Document
C53000-L1840-A001-01 2-3
The messages in DNP input direction allow:
•polling of switching devices‘ status and binary inputs,
•transmission of annunciations, measurands and meter values to the
DNP master.
The messages in DNP output direction allow:
•command outputs through the output relays of the SIPROTEC
device (external commands),
•manipulation of taggings (internal commands), which can be
changed by DNP.
Note
The allocation of the input channels and of the output relays to the
switching devices and to the output channels is defined during
parametrization of the SIPROTEC devices.
Depending on the device composition and the existing protection
packages not all of the indicated binary inputs, protection annunciations
and output relays (and corresponding DNP point index) may be available
in the SIPROTEC devices.

Parametrization in DIGSI
7SJ61/62/63 6MD63 DNP3.0 Device Profile Document
C53000-L1840-A001-01
2-4

7SJ61/62/63 6MD63 DNP3.0 Device Profile Document
C53000-L1840-A001-01 3-1
3 DNP V3.00 Device Profile
DNP V3.00 Device Profile 3
3.1 Implementation Table
In the table below, text shaded 00, 01 (start stop) indicates Subset Level
3 functionality (beyond Subset Level 2).
In the table below, text shaded as indicates functionality beyond Subset
Level 3.
OBJECT REQUEST RESPONSE
Obj VA
RDescription Func Codes Qual Codes (hex) Func Codes Qual Codes
(hex)
1 0 Binary Input - Any Variations 1 (read) 00, 01 (start-stop)
06 (no range)
07, 08 (limited qfy)
17, 28 (index)
1 2 Binary Input with Status 1 (read) 00, 01 (start-stop)
06 (no range)
07, 08 (limited qfy)
17, 28 (index)
129
(response)
00, 01
(start-stop)
17, 28
(index)
2 0 Binary Input Change - Any Variations 1 (read) 06, (no range)
07, 08 (limited qfy)
2 2 Binary Input Change with Time 1 (read) 06, (no range)
07, 08 (limited qfy)
129
(response)
130
(unsol. resp)
17, 28
(index)
10 0 Binary Output - Any Variations 1 (read) 00, 01 (start-stop)
06 (no range)
07, 08 (limited qfy)
17, 28 (index)
10 2 Binary Output Status 1 (read) 00, 01 (start-stop)
06 (no range)
07, 08 (limited qfy)
17, 28 (index)
129
(response)
00, 01
(start-stop)
17, 28
(index)
12 1 Control Relay Output Block 3 (select)
4 (operate)
5 (direct op.)
6 (dir. op.
noack)
00, 01 (start-stop)
07, 08 (limited qfy)
17, 28 (index) 129
(response)
echo of request
20 0 Binary Counter - Any Variations 1 (read) 00, 01 (start-stop)
06 (no range)
07, 08 (limited qfy)
17, 28 (index)
20 1 32-Bit Binary Counter (with Flag) 1 (read) 00, 01 (start-stop)
06 (no range)
07, 08 (limited qfy)

DNP V3.00 Device Profile
7SJ61/62/63 6MD63 DNP3.0 Device Profile Document
C53000-L1840-A001-01
3-2
OBJECT REQUEST RESPONSE
Obj VA
RDescription Func Codes Qual Codes (hex) Func Codes Qual Codes
(hex)
17, 28 (index)
22 0 Counter Change Event - Any
Variations 1 (read) 06, (no range)
07, 08 (limited qfy)
22 1 32-Bit Counter Change Event
without Time
1 (read) 06 (no range)
07, 08 (limited qfy)
30 0 16-Bit Analog Input - Any Variations 1 (read) 00, 01 (start-stop)
06 (no range)
07, 08 (limited qfy)
17, 28 (index)
30 2 16-Bit Analog Input (Static) 1 (read) 00, 01 (start-stop)
06 (no range)
07, 08 (limited qfy)
17, 28 (index)
129
(response)
00, 01
(start-stop)
17, 28
(index)
32 0 Analog Change Event - Any
Variations 1 (read) 06, (no range)
07, 08 (limited qfy)
32 2 16-Bit Analog Change Event without
Time
1 (read) 06 (no range)
07, 08 (limited qfy) 129
(response)
130
(unsol. resp)
17, 28
(index)
32 4 16-Bit Analog Change Event with
Time
1 (read) 06 (no range)
07, 08 (limited qfy) 129
(response)
130
(unsol. resp)
17, 28
(index)
50 0 Time and Date – Any Variations
50 1Time and Date 207 (where quantity = 1)
60 1 Class 0 Data 106
60 2 Class 1 Data 106 (no range)
07, 08 (limited qfy)
60 3 Class 2 Data 106 (no range)
07, 08 (limited qfy)
60 4 Class 3 Data 106 (no range)
07, 08 (limited qfy)
100, 01
80 1 Internal Indications 200, index=7

DNP V3.00 Device Profile
7SJ61/62/63 6MD63 DNP3.0 Device Profile Document
C53000-L1840-A001-01 3-3
3.2 Device Profile Document
DNP V3.00
DEVICE PROFILE DOCUMENT
Vendor Name: SIEMENS AG
Device Name: SIPROTEC 7SJ61, 7SJ62, 7SJ63 & 6MD63
Highest DNP Level Supported:
For Requests DNP-L2
For Responses DNP-L2
Device Function:
?Master CSlave
Notable objects, functions, and/or qualifiers supported in addition to the Highest DNP Levels
Supported (the complete list is described in the attached table):
For static (non-change-event) object requests, request qualifier codes 00 and 01 (start-stop), 07 and
08 (limited quantity), and 17 and 28 (index) are supported in addition to request qualifier code 06 (no
range). Static object requests sent with qualifiers 00, 01, 06, 07, or 08, will be responded with qualifiers
00 or 01. Static object requests sent with qualifiers 17 or 28 will be responded with qualifiers 17 or 28.
For change-event object requests, qualifiers 17 or 28 are always responded.
16-bit Analog Change Events with Time may be requested.
The read function code for Object 50 (Time and Date), variation 1, is supported.
The features outlined within this Device Profile have successfully passed DNP Conformance Test of
Subset Level 2 outlined in DNP3-1999 IED Certification Procedure.
Unsolicited Data and Data Link Retries are supported but have not been conformance tested to date.
Maximum Data Link Frame Size (octets):
Transmitted____292______________
Received______292______________
Maximum Application Fragment Size (octets):
Transmitted_Configurable up to 2048
Received_______2048_______
Maximum Data Link Re-tries:
CNone
?Fixed at
?Configurable, range _0_to __255___
Maximum Application Layer Re-tries:
CNone
?Configurable, range ____ to _______
(Fixed is not permitted)

DNP V3.00 Device Profile
7SJ61/62/63 6MD63 DNP3.0 Device Profile Document
C53000-L1840-A001-01
3-4
Requires Data Link Layer Confirmation:
?Never
?Always
?Sometimes If 'Sometimes', when?
______________________________________________
CConfigurable If 'Configurable', how? by the protection data processing program DIGSI
Requires Application Layer Confirmation:
?Never
?Always (not recommended)
CWhen reporting Event Data (Slave devices only)
CWhen sending multi-fragment responses (Slave devices only)
?Sometimes If 'Sometimes', when?
______________________________________________
CConfigurable If 'Configurable', how? by the protection data processing program DIGSI
Timeouts while waiting for:
Data Link Confirm ?None ?Fixed at ________ ?Variable CConfigurable
Complete Appl. Fragment CNone ?Fixed at ________ ?Variable ?Configurable
Application Confirm ?None ?Fixed at ________ ?Variable CConfigurable
Complete Appl. Response CNone ?Fixed at ________ ?Variable ?Configurable
Others Default value are configurable by the protection data processing program DIGSI
Attach explanation if 'Variable' or 'Configurable' was checked for any timeout
Sends/Executes Control Operations:
WRITE Binary Outputs CNever ?Always ?Sometimes ?Configurable
SELECT/OPERATE ?Never CAlways ?Sometimes ?Configurable
DIRECT OPERATE ?Never CAlways ?Sometimes ?Configurable
DIRECT OPERATE - NO ACK ?Never CAlways ?Sometimes ?Configurable
Count > 1 CNever ?Always ?Sometimes ?Configurable
Pulse On ?Never CAlways ?Sometimes ?Configurable
Pulse Off CNever ?Always ?Sometimes ?Configurable
Latch On ?Never CAlways ?Sometimes ?Configurable
Latch Off ?Never CAlways ?Sometimes ?Configurable
Queue CNever ?Always ?Sometimes ?Configurable
Clear Queue CNever ?Always ?Sometimes ?Configurable
Note: CONTROL RELAY OUTPUT BLOCK parameters (count, on-time, off-time) are ignored.
Attach explanation if 'Sometimes' or 'Configurable' was checked for any operation.