Siemens ACM-1 User manual

Installation Instructions
Model ACM-1
Audio Control Module
P/N 315-092083-10
Figure 1
ACM-1 PC Board
INTRODUCTION
The Model ACM-1 Audio Control Module
from Siemens Industry, Inc. is the master
control module for the MXLV audio system.
The module controls all Voice related func-
tions. It has two yellow LEDs—the TROUBLE
LED indicates ACM-1 troubles and the
TRANSMIT LED monitors network activity.
Refer to Figure 1 for the location of the
LEDs. (These troubles also appear on the
MKB-2 panel.)
ACM-1 has a supervised tone generator
which provides a variety of tones for use
with the system. Each system can have two
of the available tones. The tones are set
with CSG-M. If an application requires tone
backup, use the P6 connector on the
ACM-1 for the BTC-1 Backup Tone card.
(Refer to Figure 1.)
The ACM-1 occupies one network address.
The switch S102 shown in Figure 2 is used
to set the network address that was chosen
in CSG-M for the ACM-1 module.
OPERATIONS
1. The ACM-1 controls and supervises the
preamplifier circuit for the microphone
and wiring for the retractable cord. The
preamplifier circuit controls the volume
of any signal that enters the circuit.
2. When the microphone key is pressed,
the ACM-1 sends the preannounce tone
that was configured in CSG-M, making
the microphone the source for audio
channel 1.
Siemens Industry, Inc.
Building Technologies Division
Florham Park, NJ
Siemens Building Technologies, Ltd.
Fire Safety & Security Products
2 Kenview Boulevard
Brampton, Ontario
L6T 5E4 Canada

2
refer to the MXLV Manual, P/N 315-
092036, and the VLM-1//VSM-1/VFM-1
Instructions, P/N 315-092064.
6. The ACM-1 controls the warden’s page
that comes from the TMM-1 Telephone
Master module. When activated, the
warden’s page becomes the audio
source for selected speaker zones.
INSTALLATION
Remove all system power before instal-
lation, first battery and then AC. (To
power up, connect the AC first, then the
battery.)
To set the network address of the
module:
1. Remove the ACM-1 from its protective
bag.
2. Refer to the CSG-M configuration
printout for the address of the ACM-1
module.
3. Set the ACM-1 address on switch S102.
(Refer to Figure 2 for the location of
S102.)
3. The ACM-1 also controls a small local
speaker in the MMM-1 module. Any
of several signals available in the
System can be sent to this speaker if
selected in CSG-M.
4. Three supervised riser circuits provide
low power audio signals to the OCC-1 to
be sent to power amplifiers. The ACM-1
can also connect these risers to an
auxiliary non-emergency signal source
for use in non-emergency audio
applications.
5. The Audio Control module communi-
cates with the VSM-1 Voice Switch
modules, the VLM-1 Voice LED
modules, and the VFM-1 Fan Control
modules that are part of the system.
The VSM-1 modules provide firefighters
with a means of controlling nonautomatic
functions of the MXLV system.
The VLM-1 modules provide status
indications of the System. The VFM-1
modules provide the system operator
with automatic and manual control and
annunciation of fan control functions for
building management. These functions
are set in CSG-M. For more information
about the VSM-1, VLM-1, and VFM-1,
Figure 2
Mounting the ACM-1
5
4
3
2
1
6
7
ON DIP
8
SWITCH S102
X5

3
4. Find the correct setting for the ACM-1
address in Table 1 on page 6 of these
instructions and use dipswitch S102,
switches SW1 through SW8, to set the
address for the module.
NOTE: To open a dipswitch, press
down on the side of the
dipswitch marked OPEN. To
close a dipswitch, press down
on the side of the dipswitch
opposite the side marked
OPEN.
To open a slide switch, push
the slide to the side opposite
the side marked ON. To close a
slide switch, push the slide to
the side marked ON.
To mount the ACM-1 module:
The ACM-1 may be mounted in two differ-
ent locations in the enclosure, depending on
whether or not there is an MKB-2 in the
enclosure. (In some cases an MHD-3 is
used instead of the MKB to enable the use
of more VSMs in a system.)
1. When an MKB-2 is in the top
position of the system enclosure:
a. Mount the ACM-1 module on the
back of the MKB-2 front panel,
below the ANN-1 module. Check
that the ribbon cable connector P1 is
in the upper left corner of the board
before mounting.
b. With the board in that position, place
the module over the five threaded
mounting spacers. (See Figure 2.)
c. Fasten the module in place with the
No. 6 screws provided.
2. When an MHD-3 is used in the top
position of the enclosure (instead of
an MKB-2):
a. Mount the ACM-MPT bracket on the
4 studs located in the lower right
hand corner of the MME-3 backbox.
(These are the same studs used for
a TSP-40 printer.) Secure the
bracket with the four nuts provided.
(See Figure 3.)
b. Be sure that P1 is in the upper right
hand corner of the ACM. (Refer to
Figure 3.) Mount the ACM-1 PC
board over the six threaded mount-
ing spacers.
c. Fasten the module in place with the
five No. 6 screws provided (one of
the spacers is used for support).
(Refer to Figure 3.)
Figure 3
Alternate Mounting of ACM-1

4
Figure 4
Wiring an ACM-1 that is Mounted on an MKB-2
To wire the ACM-1:
The ACM-1 can be wired in two different
configurations: One wiring configuration is
used if an MMB (or PSR) supplies the
power and data communications (See
Figure 4).
The other wiring configuration is used
where a PS-5N7 supplies the power and
data communications, as in a remote
expander board (See Figure 5).
The wiring information below is unaffected
by whether the ACM-1 module is in the
upper or lower position of the enclosure.
CAUTION:
Remember that all cables that con-
nect to the ACM-1 are polarized
and connect in one way only. DO
NOT FORCE THEM. The location
of pin 1 on a connector is indicated
by marks on the pin or by color
tracers on the wires. In Nos.1 and
2 below, be sure the black tracer
wire is close to the 1.
1. To wire the ACM-1 in an enclosure
that has an MMB or a PSR (Refer to
Figure 4):
a. Connect the long 15-ribbon cable
(P/N 555-192238) from the MMB, P8
(or PSR-1, P5) to P5 on the ACM-1.
b. Connect the short 15-conductor
ribbon cable (P/N 555-192242) from
ANN-1, P3 to P4 on the ACM-1.
c. Connect the 14-conductor ribbon
cable (P/N 555-192236) from
TMM-1, P3 to P1 on the ACM-1, if
used.
d. Connect the 50-conductor ribbon
cable (P/N 555-192201) from
TBM-2, P3 to P2 on the ACM-1.
e. Connect the 5-conductor wire cable
(P/N 600-190220) from TBM-2, P2
to P3 on the ACM-1.
f. P6 on the ACM-1 is connected to an
optional BTC-1 module, if used.
g. If an MMM-1 is used, connect the 9-
conductor cable attached to the
MMM-1 to P7 on the ACM-1.
P5 to MMB-2/-3,P8
or to PSR-1,P5
or to PIM-1,P1
Ribbon Cable
P/N 555-192238

5
Figure 5
Wiring an ACM-1 in a Remote Expander Enclosure
2. To wire an ACM-1 module when
PS-5N7 is used to supply power and
for data communication (instead of
an MMB or a PSR):
a. Connect the long 15-conductor
ribbon cable (P/N 555-192238) from
the PS-5N7, P1 to P5 on the ACM-1.
b. Connect the 50-conductor ribbon
cable (P/N 555-192201) from
TBM-2, P3 to P2 on the ACM-1.
c. Connect the 5-conductor wire cable
(P/N 600-190220) from TBM-2, P2
to P3 on the ACM-1.
For additional information on the MXL/MXLV System,
refer to the MXL/MXLV Manual, P/N 315-092036.
ELECTRICAL RATINGS
tnerruCeludoMCDV5evitcAAm671
tnerruCeludoMCDV42evitcAAm58
tnerruCeludoMCDV42ybdnatSAm921

6
TA B L E 1
NETWORK ADDRESS PROGRAMMING
ADDR 87654321 ADDR 87654321 ADDR 87654321 ADDR 87654321
000 ILLEGAL 064 OXOOOOOO 128 XOOOOOOO 192 XXOOOOOO
001 ILLEGAL 065 OXOOOOOX 129 XOOOOOOX 193 XXOOOOOX
002 ILLEGAL 066 OXOOOOXO 130 XOOOOOXO 194 XXOOOOXO
003
004
005
006
007
008
009
010
011
012
013
014
015
016
017
018
019
020
021
022
023
024
025
026
027
028
029
030
031
032
033
034
035
036
037
038
039
040
041
042
043
044
045
046
047
048
049
050
051
052
053
054
055
OOOOOOXX
OOOOOXOO
OOOOOXOX
OOOOOXXO
OOOOOXXX
OOOOXOOO
OOOOXOOX
OOOOXOXO
OOOOXOXX
OOOOXXOO
OOOOXXOX
OOOOXXXO
OOOOXXXX
OOOXOOOO
OOOXOOOX
OOOXOOXO
OOOXOOXX
OOOXOXOO
OOOXOXOX
OOOXOXXO
OOOXOXXX
OOOXXOOO
OOOXXOOX
OOOXXOXO
OOOXXOXX
OOOXXXOO
OOOXXXOX
OOOXXXXO
OOOXXXXX
OOXOOOOO
OOXOOOOX
OOXOOOXO
OOXOOOXX
OOXOOXOO
OOXOOXOX
OOXOOXXO
OOXOOXXX
OOXOXOOO
OOXOXOOX
OOXOXOXO
OOXOXOXX
OOXOXXOO
OOXOXXOX
OOXOXXXO
OOXOXXXX
OOXXOOOO
OOXXOOOX
OOXXOOXO
OOXXOOXX
OOXXOXOO
OOXXOXOX
OOXXOXXO
OOXXOXXX
067
068
069
070
071
072
073
074
075
076
077
078
079
080
081
082
083
084
085
086
087
088
089
090
091
092
093
094
095
096
097
098
099
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
OXOOOOXX
OXOOOXOO
OXOOOXOX
OXOOOXXO
OXOOOXXX
OXOOXOOO
OXOOXOOX
OXOOXOXO
OXOOXOXX
OXOOXXOO
OXOOXXOX
OXOOXXXO
OXOOXXXX
OXOXOOOO
OXOXOOOX
OXOXOOXO
OXOXOOXX
OXOXOXOO
OXOXOXOX
OXOXOXXO
OXOXOXXX
OXOXXOOO
OXOXXOOX
OXOXXOXO
OXOXXOXX
OXOXXXOO
OXOXXXOX
OXOXXXXO
OXOXXXXX
OXXOOOOO
OXXOOOOX
OXXOOOXO
OXXOOOXX
OXXOOXOO
OXXOOXOX
OXXOOXXO
OXXOOXXX
OXXOXOOO
OXXOXOOX
OXXOXOXO
OXXOXOXX
OXXOXXOO
OXXOXXOX
OXXOXXXO
OXXOXXXX
OXXXOOOO
OXXXOOOX
OXXXOOXO
OXXXOOXX
OXXXOXOO
OXXXOXOX
OXXXOXXO
OXXXOXXX
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
XOOOOOXX
XOOOOXOO
XOOOOXOX
XOOOOXXO
XOOOOXXX
XOOOXOOO
XOOOXOOX
XOOOXOXO
XOOOXOXX
XOOOXXOO
XOOOXXOX
XOOOXXXO
XOOOXXXX
XOOXOOOO
XOOXOOOX
XOOXOOXO
XOOXOOXX
XOOXOXOO
XOOXOXOX
XOOXOXXO
XOOXOXXX
XOOXXOOO
XOOXXOOX
XOOXXOXO
XOOXXOXX
XOOXXXOO
XOOXXXOX
XOOXXXXO
XOOXXXXX
XOXOOOOO
XOXOOOOX
XOXOOOXO
XOXOOOXX
XOXOOXOO
XOXOOXOX
XOXOOXXO
XOXOOXXX
XOXOXOOO
XOXOXOOX
XOXOXOXO
XOXOXOXX
XOXOXXOO
XOXOXXOX
XOXOXXXO
XOXOXXXX
XOXXOOOO
XOXXOOOX
XOXXOOXO
XOXXOOXX
XOXXOXOO
XOXXOXOX
XOXXOXXO
XOXXOXXX
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
XXOOOOXX
XXOOOXOO
XXOOOXOX
XXOOOXXO
XXOOOXXX
XXOOXOOO
XXOOXOOX
XXOOXOXO
XXOOXOXX
XXOOXXOO
XXOOXXOX
XXOOXXXO
XXOOXXXX
XXOXOOOO
XXOXOOOX
XXOXOOXO
XXOXOOXX
XXOXOXOO
XXOXOXOX
XXOXOXXO
XXOXOXXX
XXOXXOOO
XXOXXOOX
XXOXXOXO
XXOXXOXX
XXOXXXOO
XXOXXXOX
XXOXXXXO
XXOXXXXX
XXXOOOOO
XXXOOOOX
XXXOOOXO
XXXOOOXX
XXXOOXOO
XXXOOXOX
XXXOOXXO
XXXOOXXX
XXXOXOOO
XXXOXOOX
XXXOXOXO
XXXOXOXX
XXXOXXOO
XXXOXXOX
XXXOXXXO
XXXOXXXX
XXXXOOOO
XXXXOOOX
XXXXOOXO
XXXXOOXX
XXXXOXOO
XXXXOXOX
XXXXOXXO
XXXXOXXX
056 OOXXXOOO 120 OXXXXOOO 184 XOXXXOOO 248 ILLEGAL
057 OOXXXOOX 121 OXXXXOOX 185 XOXXXOOX 249 ILLEGAL
058 OOXXXOXO 122 OXXXXOXO 186 XOXXXOXO 250 ILLEGAL
059 OOXXXOXX 123 OXXXXOXX 187 XOXXXOXX 251 ILLEGAL
060 OOXXXXOO 124 OXXXXXOO 188 XOXXXXOO 252 ILLEGAL
061 OOXXXXOX 125 OXXXXXOX 189 XOXXXXOX 253 ILLEGAL
062 OOXXXXXO 126 OXXXXXXO 190 XOXXXXXO 254 ILLEGAL
063 OOXXXXXX 127 OXXXXXXX 191 XOXXXXXX 255 ILLEGAL
O = OPEN (or OFF) X = CLOSED ( or ON)

7

Siemens Industry, Inc.
Building Technologies Division
Florham Park, NJ
Siemens Building Technologies, Ltd.
Fire Safety & Security Products
2 Kenview Boulevard
Brampton, Ontario
L6T 5E4 Canada
P/N 315-092083-10