Siemens SIMATIC NET CP 1613 A2 User manual

CP 1613 A2
___________________
___________________
___________________
___________________
___________________
___________________
___________________
SIMATIC NET
PG/PC - Industrial Ethernet
CP 1613 A2
Operating Instructions
08/2016
C79000
-G8976-C303-02
Preface
1
Description of the device
2
Software installation
3
Hardware installation
4
Configuration
5
Technical specifications
6
Approvals
A

Siemens AG
Division Process Industries and Drives
Postfa
ch 48 48
90026 NÜRNBERG
GERMANY
Document order number: C79000-G8976-C303
Ⓟ
09/2016 Subject to change
Copyright © Siemens AG 2016.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

CP 1613 A2
Operating Instructions, 08/2016, C79000-G8976-C303-02 3
Table of contents
1 Preface ................................................................................................................................................... 5
2 Description of the device......................................................................................................................... 9
3 Software installation.............................................................................................................................. 11
3.1 Installing the driver..................................................................................................................11
3.2 Installing the "SIMATIC NET PC Software" ............................................................................11
3.3 Uninstalling the "SIMATIC NET PC Software"........................................................................12
4 Hardware installation............................................................................................................................. 13
5 Configuration ........................................................................................................................................ 15
6 Technical specifications ........................................................................................................................ 17
A Approvals.............................................................................................................................................. 19

Table of contents
CP 1613 A2
4Operating Instructions, 08/2016, C79000-G8976-C303-02

CP 1613 A2
Operating Instructions, 08/2016, C79000-G8976-C303-02 5
Preface
1
Validity of this documentation
These operating instructions are valid for the following product:
●CP 1613 A2
Article number: 6GK1161-3AA01
Content of this documentation
These operating instructions contain information about the installation and configuration of
the CP 1613 A2 communications processor.
Updated operating instructions on the Internet
You will find the current version of these operating instructions on the Product Support pages
under the following entry ID:
62611661 (https://support.industry.siemens.com/cs/ww/en/view/62611661)
Further documentation
The documents listed below contain more detailed information on commissioning and using
the communications processor.
Enter the entry ID shown below of the relevant manual as the search item.
●
Configuration manual Commissioning PC Stations
This provides you with detailed information on commissioning and configuring SIMATIC
NET PC communications modules.
Entry ID:
109488960 (https://support.industry.siemens.com/cs/ww/en/view/109488960)
●
SIMATIC NET - Industrial Communication with PG/PC
–
Volume 1 – Basics (system manual)
Entry ID:
77376110 (https://support.industry.siemens.com/cs/ww/en/view/77376110)
–
Volume 2 – Interfaces (programming manual)
Entry ID:
77378184 (https://support.industry.siemens.com/cs/ww/en/view/77378184)
The system manuals introduce the topic of industrial communication and explain the
communications protocols used. There is also a description of the OPC interface as
user programming interface.

Preface
CP 1613 A2
6Operating Instructions, 08/2016, C79000-G8976-C303-02
●
Installation manual SIMATIC NET PC Software
This document contains detailed information on installing the "SIMATIC NET
PC Software".
Entry ID:
77377602 (https://support.industry.siemens.com/cs/ww/en/view/77377602)
●
System manual Industrial Ethernet Network Manual
In this document you will find detailed information about setting up an Industrial Ethernet
network.
Entry ID:
27069465 (https://support.industry.siemens.com/cs/ww/en/view/27069465)
SIMATIC NET documentation
You will find the entire SIMATIC NET documentation on the Product Support pages:
15247 (https://support.industry.siemens.com/cs/ww/en/ps/15247)
Go to the required product group and make the following settings:
→Filter criteria for entries →entry type "Manual"
See also
Support (https://support.industry.siemens.com/cs/ww/en/ps)
Trademarks
The following and possibly other names not identified by the registered trademark sign ® are
registered trademarks of Siemens AG:
SIMATIC NET, HARDNET, SOFTNET, CP 1612, CP 1613, CP 5612, CP 5613, CP 5614,
CP 5622
Industry Online Support
In addition to the product documentation, the comprehensive online information platform of
Siemens Industry Online Support at the following Internet address:
Link: (https://support.industry.siemens.com/cs/de/en/)
Apart from news, there you will also find:
●Project information: Manuals, FAQs, downloads, application examples etc.
●Contacts, Technical Forum
●The option submitting a support query:
Link: (https://support.industry.siemens.com/My/ww/en/requests)
●Our service offer:
Right across our products and systems, we provide numerous services that support you
in every phase of the life of your machine or system - from planning and implementation
to commissioning, through to maintenance and modernization.

Preface
CP 1613 A2
Operating Instructions, 08/2016, C79000-G8976-C303-02 7
You will find contact data on the Internet at the following address:
Link: (http://www.automation.siemens.com/aspa_app/?ci=yes&lang=en)
SITRAIN - Training for Industry
The training offer includes more than 300 courses on basic topics, extended knowledge and
special knowledge as well as advanced training for individual sectors - available at more
than 130 locations. Courses can also be organized individually and held locally at your
location.
You will find detailed information on the training curriculum and how to contact our customer
consultants at the following Internet address:
Link: (http://sitrain.automation.siemens.com/DE/sitrain/default.aspx?AppLang=en)
Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions only form one element of such a concept.
Customer is responsible to prevent unauthorized access to its plants, systems, machines
and networks. Systems, machines and components should only be connected to the
enterprise network or the internet if and to the extent necessary and with appropriate security
measures (e.g. use of firewalls and network segmentation) in place.
Additionally, Siemens’ guidance on appropriate security measures should be taken into
account. For more information about industrial security, please visit
http://www.siemens.com/industrialsecurity
Siemens’ products and solutions undergo continuous development to make them more
secure. Siemens strongly recommends to apply product updates as soon as available and to
always use the latest product versions. Use of product versions that are no longer supported,
and failure to apply latest updates may increase customer’s exposure to cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed under
https://support.industry.siemens.com/cs/ww/de/ps/15247/pm
SIMATIC NET glossary
Explanations of many of the specialist terms used in this documentation can be found in the
SIMATIC NET glossary.
You will find the SIMATIC NET glossary on the Internet at the following address:
50305045 (http://support.automation.siemens.com/WW/view/en/50305045)

CP 1613 A2
Operating Instructions, 08/2016, C79000-G8976-C303-02 9
Description of the device
2
Product features
The CP 1613 A2 is a PCI module for connecting PGs/PCs to Industrial Ethernet. The
essential properties are as follows:
●RJ-45 jack for Industrial Ethernet for connecting a TP cable (TP -twisted-pair)
●15-pin D-sub socket for AUI and ITP
The 15-pin D-sub socket with slide locking mechanism is intended for connection of both
AUI transceiver cables (AUI - Attachment Unit Interface) and for connection of ITP cables
(ITP - Industrial Twisted Pair).
●The following data rates are supported:
–10/100 Mbps (half/full duplex)
●Own processor on the CP 1613 A2 relieves the PC/PG CPU
●Autosensing, autonegotiation
●The changeover between the AUI and ITP connector is made automatically by the CP
1613 A2 if you use Siemens ITP cables.
●ISO and TCP/IP transport protocol onboard
Hardware requirements
The CP 1613 A2 requires a PCI slot for operation.
LED display
To indicate module activity, the CP 1613 A2 has two LEDs on the RJ-45 jackl that are lit
when data is being received (green) and when data is being sent (yellow).

Description of the device
CP 1613 A2
10 Operating Instructions, 08/2016, C79000-G8976-C303-02