Siemens SIMOTION P320-4 E User manual

SIMOTION
SIMOTION P320-4 E / P320-4 S
Manual
Valid as of version V5.2
03/2018
A5E36004933B
Preface
Safety instructions 1
Industrial security 2
Description 3
Application planning 4
Interfaces 5
Installation/mounting 6
Connection 7
Troubleshooting/FAQs 8
Technical data 9
Dimension drawings 10
Spare parts 11
Standards and approvals A
ESD Guideline B

Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be
used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property
damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified
personnel are those who, based on their training and experience, are capable of identifying risks and avoiding
potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described.
Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in
this publication is reviewed regularly and any necessary corrections are included in subsequent editions.
Siemens AG
Division Digital Factory
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E36004933B
Ⓟ 02/2018 Subject to change
Copyright © Siemens AG 2016 - 2018.
All rights reserved

Preface
Preface
This document is part of the SIMOTION P documentation package.
This documentation describes the SIMOTION P320‑4 hardware platform which can be
delivered in the SIMOTION P320-4 E and SIMOTION P320-4 S hardware versions:
● SIMOTION P320‑4 E with the Windows Embedded Standard 7 32-bit operating system and
real-time expansion for SIMOTION.
Successor to SIMOTION P320-3.
● SIMOTION P320‑4 E with the Windows 7 Ultimate 32-bit operating system and real-time
expansion for SIMOTION.
Successor to SIMOTION P350-3.
References
The following documents contain the descriptions for the SIMOTION P hardware platform:
● SIMOTION P320-4 E / P320-4 S, Manual, Edition 09/2016
● SIMOTION P320-4 E / P320-4 S, Commissioning and Hardware Installation Manual, Edition
09/2016
Validity range
This manual applies to the SIMOTION P320-4 E and SIMOTION P320-4 S devices as of
product level SIMOTION V4.5.
Standards
The SIMOTION system was developed in accordance with ISO 9001 quality guidelines.
Chapters in this documentation
The following sections describe the purpose and the use of this documentation:
● Safety instructions
Contains fundamental safety instructions for SIMOTION and specific safety instructions for
SIMOTION P320-4.
● Description
System overview and product description for SIMOTION P320-4. The communication
versions are also described.
● Use planning
Points to note in advance: upon delivery, the permitted installation positions, environmental
and ambient conditions and electromagnetic compatibility.
SIMOTION P320-4 E / P320-4 S
Manual, 03/2018, A5E36004933B 3

● Interfaces
Description of the interfaces and operator control and display elements for
SIMOTION P320-4.
●Installation/mounting
An overview of the installation of the SIMOTION P320-4 taking into account the mounting
positions.
● Connecting
This section provides general information and important notes that you must observe when
connecting the SIMOTION P320‑4.
● Troubleshooting/FAQs
List of possible errors and their remedies.
● Technical specifications
This section contains an overview of the technical data, which is listed in detail for the
individual components.
● Dimension drawings
In this section you can find dimension drawings and dimensions of the SIMOTION P320‑4.
● Spare parts
You can find information about the spare parts for the SIMOTION P320-4 here.
● Appendix
In addition to the safety information, the annexes also contain information about the
standards, approvals and EGB guideline.
● Index
Alphabetical directory for locating information.
SIMOTION Documentation
An overview of the SIMOTION documentation can be found in the SIMOTION Documentation
Overview document.
This documentation is included as electronic documentation in the scope of delivery of
SIMOTION SCOUT. It comprises ten documentation packages.
The following documentation packages are available for SIMOTION product version V5.2:
● SIMOTION Engineering System Handling
● SIMOTION System and Function Descriptions
● SIMOTION Service and Diagnostics
● SIMOTION IT
● SIMOTION Programming
● SIMOTION Programming - References
● SIMOTION C
● SIMOTION P
Preface
SIMOTION P320-4 E / P320-4 S
4Manual, 03/2018, A5E36004933B

● SIMOTION D
●SIMOTION Supplementary Documentation
Hotline and Internet addresses
SIMOTION at a glance
We have compiled an overview page from our range of information about SIMOTION with the
most important information on frequently asked topics - which can be opened with only one
click.
Whether beginner or experienced SIMOTION user – the most important downloads, manuals,
tutorials, FAQs, application examples, etc. can be found at
https://support.industry.siemens.com/cs/ww/en/view/109480700
Additional information
Click the following link to find information on the following topics:
● Documentation overview
● Additional links to download documents
● Using documentation online (find and search manuals/information)
https://support.industry.siemens.com/cs/ww/en/view/109479653
My Documentation Manager
Click the following link for information on how to compile documentation individually on the
basis of Siemens content and how to adapt it for the purpose of your own machine
documentation:
https://support.industry.siemens.com/My/ww/en/documentation
Training
Click the following link for information on SITRAIN - Siemens training courses for automation
products, systems and solutions:
http://www.siemens.com/sitrain
FAQs
Frequently Asked Questions can be found in SIMOTION Utilities & Applications, which are
included in the scope of delivery of SIMOTION SCOUT, and in the Service&Support pages in
Product Support:
https://support.industry.siemens.com/cs/de/en/ps/14505/faq
Preface
SIMOTION P320-4 E / P320-4 S
Manual, 03/2018, A5E36004933B 5

Technical support
Country-specific telephone numbers for technical support are provided on the Internet under
Contact:
https://support.industry.siemens.com/cs/ww/en/sc/2090
Product disposal
SIMOTION P is an environmentally friendly product! It includes the following features:
●In spite of its excellent resistance to fire, the flame-resistant agent in the plastic used for
the housing does not contain halogens.
● Marking of the plastic materials as per ISO 11469.
● Less material used because the unit is smaller and with fewer components thanks to
integration in ASICs.
The product is to be disposed of in accordance with national regulations.
The product described in this manual can be recycled owing to its low pollutant content. For
environmentally friendly recycling and disposal of your old device, please contact a company
certified for the disposal of electronic waste and dispose of the device in accordance with the
regulations in your country.
If you have any further questions about disposal and recycling, please contact your local
Siemens representative. Contact details can be found in our contacts database on the Internet
at:
http://www.automation.siemens.com/partner/index.asp
Preface
SIMOTION P320-4 E / P320-4 S
6Manual, 03/2018, A5E36004933B

Table of contents
Preface.........................................................................................................................................................3
1Safety instructions......................................................................................................................................11
1.1 Fundamental safety instructions............................................................................................11
1.1.1 General safety instructions.....................................................................................................11
1.1.2 Safety instructions for electromagnetic fields (EMF)..............................................................14
1.1.3 Handling electrostatic sensitive devices (ESD)......................................................................14
1.1.4 Security information...............................................................................................................15
1.1.5 Danger to life due to software manipulation when using removable storage media..............15
1.1.6 Residual risks of power drive systems...................................................................................16
1.2 Specific safety instructions for the SIMOTION P320-4..........................................................17
1.2.1 General safety instructions for the SIMOTION P320-4..........................................................17
1.2.2 Notes on use..........................................................................................................................19
2 Industrial security........................................................................................................................................21
2.1 Security concept for SIMOTION P320-4................................................................................21
2.1.1 Security..................................................................................................................................21
2.2 Why is industrial security so important?.................................................................................24
2.2.1 Trends in the IT sector...........................................................................................................24
2.2.2 Possible corporate security holes..........................................................................................25
2.3 General security measures....................................................................................................26
2.3.1 Overview................................................................................................................................26
2.3.2 Plant security..........................................................................................................................27
2.3.2.1 Physical protection of critical production areas......................................................................27
2.3.3 Network security.....................................................................................................................28
2.3.3.1 Network segmentation...........................................................................................................28
2.3.4 System integrity......................................................................................................................31
2.3.4.1 System hardening..................................................................................................................31
2.3.4.2 Patch management................................................................................................................32
2.4 Product-specific measures.....................................................................................................33
2.4.1 Virus scanners, Windows security patches, SIMOTION P.....................................................33
2.4.2 Changing the Windows user password..................................................................................34
2.4.3 Changing the AutoLogin.........................................................................................................38
2.4.4 Deactivating the remote desktop connection.........................................................................45
3 Description..................................................................................................................................................49
3.1 System overview....................................................................................................................49
3.2 SIMOTION P320-4 product description.................................................................................51
3.2.1 SIMOTION P320-4 overview..................................................................................................51
3.2.2 Features.................................................................................................................................52
3.2.3 SIMOTION P320-4 (hardware) structure...............................................................................54
3.2.4 Interfaces and operating elements.........................................................................................55
3.2.5 SIMOTION P Runtime (software) structure............................................................................55
3.2.6 Components...........................................................................................................................56
SIMOTION P320-4 E / P320-4 S
Manual, 03/2018, A5E36004933B 7

3.3 HMI and SIMOTION SCOUT.................................................................................................59
3.3.1 HMI and SIMOTION SCOUT Overview.................................................................................59
3.3.2 Local HMI or ES on SIMOTION P320-4.................................................................................59
3.3.2.1 Setting up a network bridge - MAC bridge miniport...............................................................61
3.3.3 HMI or ES via PROFINET......................................................................................................72
3.3.4 HMI or ES via Ethernet..........................................................................................................73
3.3.5 HMI or ES via IsoPROFIBUS (optional).................................................................................74
4 Application planning...................................................................................................................................77
4.1 Unpacking and checking the delivery.....................................................................................77
4.2 Identification data of the device..............................................................................................79
4.3 Permissible mounting positions..............................................................................................82
4.4 Environmental conditions.......................................................................................................83
4.5 Electromagnetic compatibility.................................................................................................85
5 Interfaces....................................................................................................................................................87
5.1 Hardware components of the SIMOTION P320-4..................................................................87
5.2 Overview of operator control and display elements...............................................................89
5.3 Control elements....................................................................................................................90
5.4 Status displays.......................................................................................................................91
5.5 Overview of the SIMOTION P320-4 interfaces......................................................................93
5.6 PROFINET onboard...............................................................................................................94
5.7 Ethernet..................................................................................................................................95
5.8 DVI-I.......................................................................................................................................96
5.9 DisplayPort.............................................................................................................................98
5.10 USB 3.0..................................................................................................................................99
5.11 CFast card ...........................................................................................................................100
5.12 COM1...................................................................................................................................101
5.13 IsoPROFIBUS board (optional)............................................................................................102
6 Installation/mounting.................................................................................................................................103
6.1 Installing the device..............................................................................................................103
6.2 Permissible mounting positions............................................................................................104
6.2.1 Standard rail mounting and vertical mounting......................................................................105
6.2.1.1 Standard rail mounting.........................................................................................................105
6.2.1.2 Vertical mounting.................................................................................................................107
6.3 Installation notes..................................................................................................................109
6.4 Overview of operating modes for the SIMOTION P320-4....................................................111
6.5 Decentralized structure........................................................................................................112
7 Connection...............................................................................................................................................113
7.1 Requirements.......................................................................................................................113
Table of contents
SIMOTION P320-4 E / P320-4 S
8Manual, 03/2018, A5E36004933B

7.2 Overview of connections......................................................................................................114
7.3 Notes on connecting............................................................................................................116
7.4 Protective conductor connection and potential equalization................................................118
7.5 Connecting peripheral equipment........................................................................................120
7.6 Connecting the power supply (24 VDC)...............................................................................121
7.7 Connecting the device to networks......................................................................................123
7.8 Installing the strain relief......................................................................................................124
8 Troubleshooting/FAQs..............................................................................................................................125
8.1 Error correction....................................................................................................................125
8.2 Hotplug Enabled BIOS settings............................................................................................127
9 Technical data..........................................................................................................................................133
9.1 Overview of the technical specifications..............................................................................133
9.2 General technical specifications...........................................................................................134
9.3 Ambient conditions...............................................................................................................136
9.4 Technical data of the IsoPROFIBUS board.........................................................................138
9.5 Power requirements of the components..............................................................................140
9.6 Integrated DC power supply.................................................................................................141
9.7 Technical data for the SITOP smart 24 V/10 A....................................................................142
9.8 Typical power consumption..................................................................................................144
10 Dimension drawings.................................................................................................................................145
10.1 Overview of the dimensional drawings.................................................................................145
10.2 Device dimension drawing for standard rail mounting.........................................................146
10.3 Device dimension drawing for vertical mounting..................................................................148
10.4 Dimension drawing of device with one expansion card.......................................................151
11 Spare parts...............................................................................................................................................153
11.1 Available spare parts for SIMOTION P320-4.......................................................................153
A Standards and approvals..........................................................................................................................155
A.1 General rules........................................................................................................................155
B ESD Guideline..........................................................................................................................................157
B.1 ESD definition......................................................................................................................157
B.2 Electrostatic charging of individuals.....................................................................................158
B.3 Basic measures for protection against discharge of static electricity...................................159
Index.........................................................................................................................................................161
Table of contents
SIMOTION P320-4 E / P320-4 S
Manual, 03/2018, A5E36004933B 9

Table of contents
SIMOTION P320-4 E / P320-4 S
10 Manual, 03/2018, A5E36004933B

Safety instructions 1
1.1 Fundamental safety instructions
1.1.1 General safety instructions
DANGER
Danger to life due to live parts and other energy sources
Death or serious injury can result when live parts are touched.
●Only work on electrical devices when you are qualified for this job.
● Always observe the country-specific safety rules.
Generally, six steps apply when establishing safety:
1. Prepare for shutdown and notify all those who will be affected by the procedure.
2. Disconnect the machine from the supply.
– Switch off the machine.
– Wait until the discharge time specified on the warning labels has elapsed.
– Check that it really is in a no-voltage condition, from phase conductor to phase
conductor and phase conductor to protective conductor.
– Check whether the existing auxiliary supply circuits are de-energized.
– Ensure that the motors cannot move.
3. Identify all other dangerous energy sources, e.g. compressed air, hydraulic systems, or
water.
4. Isolate or neutralize all hazardous energy sources by closing switches, grounding or short-
circuiting or closing valves, for example.
5. Secure the energy sources against switching on again.
6. Ensure that the correct machine is completely interlocked.
After you have completed the work, restore the operational readiness in the inverse sequence.
WARNING
Danger to life from hazardous voltage when connecting an unsuitable power supply
Touching live components can result in death or severe injury.
●Only use power supplies that provide SELV (Safety Extra Low Voltage) or PELV
(Protective Extra Low Voltage) output voltages for all connections and terminals of the
electronics modules.
SIMOTION P320-4 E / P320-4 S
Manual, 03/2018, A5E36004933B 11

WARNING
Danger to life from touching live parts on damaged devices
Improper handling of devices can result in damage.
For damaged devices, hazardous voltages can be present at the enclosure or at exposed
components; if touched, this can result in death or severe injury.
● Observe the limit values specified in the technical specifications during transport, storage,
and operation.
● Do not use damaged devices.
WARNING
Danger to life through electric shock due to unconnected cable shields
Hazardous touch voltages can occur through capacitive cross-coupling due to unconnected
cable shields.
● As a minimum, connect cable shields and the cores of power cables that are not used
(e.g. brake cores) at one end at the grounded housing potential.
WARNING
Danger to life due to electric shock when not grounded
For missing or incorrectly implemented protective conductor connection for devices with
protection class I, high voltages can be present at open, exposed parts, which when touched,
can result in death or severe injury.
● Ground the device in compliance with the applicable regulations.
WARNING
Danger to life due to fire spreading if housing is inadequate
Fire and smoke development can cause severe personal injury or material damage.
● Install devices without a protective housing in a metal control cabinet (or protect the device
by another equivalent measure) in such a way that contact with fire inside and outside the
device is prevented.
● Ensure that smoke can only escape via controlled and monitored paths.
Safety instructions
1.1 Fundamental safety instructions
SIMOTION P320-4 E / P320-4 S
12 Manual, 03/2018, A5E36004933B

WARNING
Danger to life from unexpected movement of machines when using mobile wireless devices
or mobile phones
Using mobile radios or mobile phones with a transmit power > 1 W closer than approx. 2 m
to the components may cause the devices to malfunction, influence the functional safety of
machines therefore putting people at risk or causing material damage.
● Switch off wireless devices or mobile phones in the immediate vicinity of the components.
WARNING
Danger to life due to fire if overheating occurs because of insufficient ventilation clearances
Inadequate ventilation clearances can cause overheating of components followed by fire and
smoke development. This can cause death or serious injury. This can also result in increased
downtime and reduced service life for devices/systems.
● Ensure compliance with the specified minimum clearance as ventilation clearance for the
respective component.
WARNING
Danger of an accident occurring due to missing or illegible warning labels
Missing or illegible warning labels can result in accidents involving death or serious injury.
●Check that the warning labels are complete based on the documentation.
● Attach any missing warning labels to the components, in the national language if
necessary.
● Replace illegible warning labels.
WARNING
Danger to life when safety functions are inactive
Safety functions that are inactive or that have not been adjusted accordingly can cause
operational faults on machines that could lead to serious injury or death.
● Observe the information in the appropriate product documentation before commissioning.
● Carry out a safety inspection for functions relevant to safety on the entire system, including
all safety-related components.
● Ensure that the safety functions used in your drives and automation tasks are adjusted
and activated through appropriate parameterizing.
● Perform a function test.
● Only put your plant into live operation once you have guaranteed that the functions relevant
to safety are running correctly.
Safety instructions
1.1 Fundamental safety instructions
SIMOTION P320-4 E / P320-4 S
Manual, 03/2018, A5E36004933B 13

Note
Important safety notices for safety functions
If you want to use safety functions, you must observe the safety notices in the safety manuals.
1.1.2 Safety instructions for electromagnetic fields (EMF)
WARNING
Danger to life from electromagnetic fields
Electromagnetic fields (EMF) are generated by the operation of electrical power equipment
such as transformers, converters or motors.
People with pacemakers or implants are at a special risk in the immediate vicinity of these
devices/systems.
●Ensure that the persons involved are the necessary distance away (minimum 2 m).
1.1.3 Handling electrostatic sensitive devices (ESD)
Electrostatic sensitive devices (ESD) are individual components, integrated circuits, modules
or devices that may be damaged by either electric fields or electrostatic discharge.
NOTICE
Damage through electric fields or electrostatic discharge
Electric fields or electrostatic discharge can cause malfunctions through damaged individual
components, integrated circuits, modules or devices.
● Only pack, store, transport and send electronic components, modules or devices in their
original packaging or in other suitable materials, e.g conductive foam rubber of aluminum
foil.
● Only touch components, modules and devices when you are grounded by one of the
following methods:
– Wearing an ESD wrist strap
– Wearing ESD shoes or ESD grounding straps in ESD areas with conductive flooring
● Only place electronic components, modules or devices on conductive surfaces (table with
ESD surface, conductive ESD foam, ESD packaging, ESD transport container).
Safety instructions
1.1 Fundamental safety instructions
SIMOTION P320-4 E / P320-4 S
14 Manual, 03/2018, A5E36004933B

1.1.4 Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens' products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be connected
to an enterprise network or the internet if and to the extent such a connection is necessary
and only when appropriate security measures (e.g. firewalls and/or network segmentation) are
in place.
For additional information on industrial security measures that may be implemented, please
visit (https://www.siemens.com/industrialsecurity).
Siemens' products and solutions undergo continuous development to make them more secure.
Siemens strongly recommends that product updates are applied as soon as they are available
and that the latest product versions are used. Use of product versions that are no longer
supported, and failure to apply the latest updates may increase customers' exposure to cyber
threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed under (https://www.siemens.com/industrialsecurity).
1.1.5 Danger to life due to software manipulation when using removable storage media
WARNING
Danger to life due to software manipulation when using removable storage media
The storage of files on removable storage media involves a high risk of infection, e.g. via
viruses or malware. Incorrect parameter assignment can cause machines to malfunction,
which can lead to injuries or death.
● Protect the files on removable storage media against harmful software through appropriate
protective measures, e.g. virus scanners.
Safety instructions
1.1 Fundamental safety instructions
SIMOTION P320-4 E / P320-4 S
Manual, 03/2018, A5E36004933B 15

1.1.6 Residual risks of power drive systems
When performing the risk assessment for a machine or plant in accordance with the respective
local regulations (e.g. EC Machinery Directive), the machine manufacturer or plant constructor
must take into account the following residual risks associated with the control and drive
components of a drive system:
1. Unintentional movements of driven machine or system components during commissioning,
operation, maintenance and repairs caused by, for example:
– Hardware and/or software errors in the sensors, control system, actuators, and cables
and connections
– Response times of the control system and of the drive
– Operation and/or environmental conditions outside the specification
– Condensation/conductive contamination
– Parameterization, programming, cabling, and installation errors
– Use of wireless devices / mobile phones in the immediate vicinity of electronic
components
– External influences/damage
– X-rays, ionizing radiation and cosmic radiation
2. Unusually high temperatures, including open flames, as well as emissions of light, noise,
particles, gases, etc., can occur inside and outside the components under fault conditions
caused by, for example:
– Component failure
– Software errors
– Operation and/or environmental conditions outside the specification
– External influences/damage
3. Hazardous shock voltages caused by, for example:
– Component failure
– Influence during electrostatic charging
– Induction of voltages in moving motors
– Operation and/or environmental conditions outside the specification
– Condensation/conductive contamination
– External influences/damage
4. Electrical, magnetic and electromagnetic fields generated in operation that can pose a risk
to people with a pacemaker, implants or metal replacement joints, etc., if they are too close
5. Release of environmental pollutants or emissions as a result of improper operation of the
system and/or failure to dispose of components safely and correctly
For more information about the residual risks of the drive system components, see the relevant
sections in the technical user documentation.
Safety instructions
1.1 Fundamental safety instructions
SIMOTION P320-4 E / P320-4 S
16 Manual, 03/2018, A5E36004933B

1.2 Specific safety instructions for the SIMOTION P320-4
1.2.1 General safety instructions for the SIMOTION P320-4
WARNING
Life-threatening voltages are present with an open control cabinet
When you install the device in a control cabinet, some areas or components in the open
control cabinet may be carrying life-threatening voltages.
If you touch these areas or components, you may be killed by electric shock.
Switch off the power supply to the cabinet before opening it.
System expansions
NOTICE
Damage through system expansions
Device and system expansions may be faulty and can affect the entire machine or plant.
The installation of expansions can damage the device, machine or plant.
Device and system expansions may violate safety rules and regulations regarding radio
interference suppression.
If you install or exchange system expansions and damage your device, the warranty becomes
void.
Note the following for system expansions:
●Only install system expansion devices designed for this device. Contact your technical
support team or where you purchased your PC to find out which system expansion devices
may safely be installed.
● Observe the information on electromagnetic compatibility (Page 155).
NOTICE
"Open Type" UL508
Note that the device is classified as "Open Type" for use in the area of Industrial Control
Equipment (UL508). Installation of the device in an enclosure according to UL508 is
conditional for approval or operation according to UL508.
Safety instructions
1.2 Specific safety instructions for the SIMOTION P320-4
SIMOTION P320-4 E / P320-4 S
Manual, 03/2018, A5E36004933B 17

Battery and rechargeable battery
WARNING
Risk of explosion and release of harmful substances
Improper handling of lithium batteries can result in an explosion of the batteries.
Explosion of the batteries and the released pollutants can cause severe physical injury. Worn
batteries jeopardize the function of the device.
Note the following when handling lithium batteries:
● Replace used batteries in good time, see the section "Replacing the backup battery" in
the Commissioning and Hardware Installation Manual.
● Replace the lithium battery only with an identical battery or types recommended by the
manufacturer (Article No.: A5E30314053).
● Do not throw lithium batteries into fire, do not solder on the cell body, do not recharge, do
not open, do not short-circuit, do not reverse polarity, do not heat above 100°C and protect
from direct sunlight, moisture and condensation.
High frequency radiation
NOTICE
Unintentional operating situations
High frequency radiation, e g. from a cellular phone, interferes with device functions and can
result in malfunctioning of the device.
Persons are injured and the plant is damaged.
Avoid high-frequency radiation:
● Remove radiation sources from the environment of the device.
● Switch off radiating devices.
● Reduce the radio output of radiating devices.
● Observe the information on electromagnetic compatibility (Page 155).
ESD Guideline
Electrostatic sensitive devices can be labeled with an appropriate symbol.
NOTICE
Electrostatic sensitive devices (ESD)
When you touch electrostatic sensitive components, you can destroy them through voltages
that are far below the human perception threshold.
If you work with components that can be destroyed by electrostatic discharge, observe the
ESD Guideline.
Safety instructions
1.2 Specific safety instructions for the SIMOTION P320-4
SIMOTION P320-4 E / P320-4 S
18 Manual, 03/2018, A5E36004933B

Further information
You can find more detailed information about the EGB Guideline in Annex B in the section with
the same name.
1.2.2 Notes on use
WARNING
Hazards on an unprotected machine or plant
According to the results of a risk analysis, hazards can occur on an unprotected machine.
The hazards can result in personal injury.
According to the risk analysis, the risk of personal injury can be avoided with the following
measures:
●Additional protective devices on the machine or plant. With this, especially the
programming, configuration and wiring of the inserted I/O modules have to be executed,
in accordance with the necessary risk analysis identified safety performance (SIL, PL or
Cat.).
● The correct use of the device has to be verified with a function test on the system. This
test can detect programming, configuration and wiring errors.
● Documentation of the test results that you can enter in the relevant safety records when
required.
NOTICE
Ambient conditions
Ambient conditions for which the device is not suitable can cause faults or damage the device.
Note the following:
● Operate the device only in closed rooms. Failure to comply nullifies the warranty.
● Operate the device only in accordance with the ambient conditions specified in the
technical specifications.
● Protect the device against dust, moisture and heat.
● Do not expose the device to direct sunlight or other strong sources of light.
● Without additional measures, such as a supply of clean air, the device may not be used
in locations with harsh operating conditions caused by acidic vapors or gases.
● Observe the permissible mounting positions of the device.
● Do not obstruct the venting slots of the device.
Note
Use in an industrial environment without additional protective measures
This device was designed for use in a normal industrial environment according to
IEC 60721-3-3.
Safety instructions
1.2 Specific safety instructions for the SIMOTION P320-4
SIMOTION P320-4 E / P320-4 S
Manual, 03/2018, A5E36004933B 19

Safety instructions
1.2 Specific safety instructions for the SIMOTION P320-4
SIMOTION P320-4 E / P320-4 S
20 Manual, 03/2018, A5E36004933B