Siemens Types NRK 16-T../A User manual

INTEGRAL RSA K21-04.10
1/8
Application controllers en - 06.2001
Siemens Building Technologies Landis & Staefa Division
NRK16/A (with NSA) NRK16-B/A (with NSA)
T pes
NRK16/A Application cont olle with ten unive sal inputs1) and
two analogue, two digital and two combined outputs
NRK16-B/A Like NRK16/A, but with panel fo simple local ope ation
NSA Application modules, va ying acco ding to count y o egion,
fo plugging into base units
NRK16-T../A NRK16/A + NITEL integ ated communications module fo a maximum
of th ee additional devices (see manual NT21)
NRK14-T../A Like NRK16-T../A, but without analogue outputs (see
manual NT21)
NRK16-WEB/A NRK16/A + integ ated NIWEB communications module fo ope ation
of up to 15 additional devices via the Inte net (K1-07.62)
Technical data
Supply voltage Ext a low voltage (SELV-E)
Nominal voltage AC 24 V, 50/60 Hz
 Max. tole ance +15 / 10 %
Powe consumption
 Without output pe iphe als 3 VA
 With output pe iphe als Max. 12 VA
Fuse The mal element (PTC)
Supply voltage fo pe iphe al devices
and emote ope ato te minal
Output voltage DC15V ±10%, elect ically isolated f om AC24V
Output cu ent Max. 150 mA
Signal inputs
2)
Unive sal inputs
3)
 Numbe 101)
 Use Can be st uctu ed as T1, Ni1000, DC 0...10 V,
digital volt-f ee, o fo connection of NMID
 Input impedance Ri (pull-up esisto ) = 10 kW to DC +15 V o
100 kW to GND (change-ove , see p. 6)
Remote cont ol input
Use Can be st uctu ed as T1, Ni1000, DC 0 ... 10 V,
min. 1.5 sink, digital volt-f ee contacts, o NMID
 Input impedance Ri (pull-up esisto ) = 10 kW to DC +15 V
Signal outputs
2)
Digital outputs
 Numbe 2
 Signal DC 0 / 24 V, 20 / +15 %
 Sou ce cu ent Max. 50 mA
Analogue outputs
 Numbe 2
 Range DC 0 ... 10 V
 Sou ce/sink cu ent Max. 2 mA
Technical data continued on page 2
Electrical protection
The powe supply is ove load-p otected
with a PTC the mal element.
All DC voltages a e elect ically isolated
f om the AC 24 V input.
All the inputs a e p otected against ove -
voltage (max. AC/DC 45 V). Low-pass fil-
te s p event fluctuations in measu ement.
All outputs a e sustained sho t-ci cuit
p oof.
High f equency inte fe ence is supp es-
sed by means of filte s, o in the case of
capacitive inte fe ence, discha ged via
the (ea thed) housing o the TE te minal
(functional ea th).
Important:
For direction connection of AC 24 V
3- ire peripheral devices, "GND"
and "NS" (^) must be connected.
NRK16/A, NRK16-B/A,
(NRK16-T../A, NRK14-T../A,
NRK16-WEB/A)
Control and interlock devices
Application controllers with
pre-programmed system-specific
application modules.
The controllers may be used
 as stand-alone control and
interlock devices
 for remote process control within
a management system
Especially suitable for use in small
heating, ventilation and air
conditioning systems.
1) The NMID multiplexe enables fou digital
inputs to be connected to a unive sal
output. (see K21-06.55). The function is
integ ated by use of a st uctu e mac o.
2) When connecting pe iphe al devices
with special input o output signals
(e.g. Pt100, phase cut o 3-position sig-
nals), the NTIO (NTIOS) single module
ca ie o an NATU adapte can be
used. (See K21-06.50 and K21-06.52).
3) The T1/Ni1000 supply voltage can be
disabled at the inputs (see page 5). DIP
switches a e p ovided to switch the
inputs f om T1 to Ni1000 and vice ve sa.

INTEGRAL RSA K21-04.10
2/8
Application controllers en - 06.2001
Siemens Building Technologies Landis & Staefa Division
Technical data continued from page 1
Combined outputs
 Numbe 2
 Type One te minal with a digital and one with an
analogue output (see data above)
 Digital/analogue elationship High > 50 %, low < 30 % of analogue signal
Remote cont ol output
 Range DC 0 ... 10 V
 Sou ce cu ent Max. 10 mA
 Sink cu ent Max. 3 mA
P oduct data
Accu acy Class 0.5
Sampling ate
 Inte nal 100 ms
 St uctu e 0.2  1 s
Data p otection afte powe failu e
 St uctu es and pa amete s 4)> 10 yea s
 Time / date 4) Equivalent to batte y life
 Adjustable values in NRK16-B/A4) Equivalent to batte y life
NSA application module EEPROM Type 28C64
Connections
Connection te minals 2.5 mm2 sc ew te minals
Cable type and length See installation inst uctions, K21-11.20
Communication
RS bus Elect ically isolated f om AC 24 V
and signal outputs
 T ansmission speed 9600 baud
 Max. cable length (RS bus) 2400 m
 NRK16../A connection to RS bus F om se vice socket via 10-co e ibbon cable
to NARB/A adapte
Se vice te minal NBRN ope ato te minal; plugs di ectly
into se vice socket
Weight excluding packaging
NRK16/A 1.15 kg
NRK16-B/A 1.25 kg
NSA application module 0.06 kg
Dimensions (W x H x D)
NRK16../A 162 x 252 x 52 mm
NSA application module 24 x 59 x 49 mm
Mounting Snap-mounted on DIN ails o sc ewed to a
flat su face; NRK16-B/A installed in cont ol
panel f ont with the Z402 mounting kit
Safety
P oduct safety EN 61010-1
 Contamination level 2
Elect ical safety SELV-E (PELV to IEC 364-4-41)
Gene al ambient conditions
Use Installed in cont ol panel
Tempe atu e ange
 Ope ation 5 ... 45 °C
 Sto age 25 ... 70 °C
Ambient humidity 10 ... 90 % h, non-condensing
Confo mity This p oduct meets the equi ements fo
ma king and is tested
Battery
In the event of a powe failu e, data is
p otected against loss by a eplaceable
lithium batte y (se vice life app ox. 5 ...10
yea s).
Used and faulty batte ies must be dispo-
sed of in acco dance with local egulations.
4) Applies to pe manently plugged-in
application modules

INTEGRAL RSA K21-04.10
3/8
Application controllers en - 06.2001
Siemens Building Technologies Landis & Staefa Division
Brief description
The R A controllers are microprocessor-based DDC controllers comprising a
base unit and a plug-in application module.
Each plug-in application module contains an EEPROM preprogrammed with
a given application chosen from a wide range of heating, ventilation and
air conditioning applications. The application modules are held in application
libraries in the various national and regional taefa offices. They can be se-
lected according to the system and plugged into the base unit. The engineer-
ing required is thus minimal, and since suitable default settings are provided
for setpoints, parameters etc., commissioning is extremely easy.
If no suitable standard solution is available, a program for the specific appli-
cation can be designed in APIM and downloaded to the module from a PC.
At the same time, the application modules are freely programmable, so
that if no suitable standard solution is available, a program can be
designed in APIM and downloaded to the module from a PC.
The EEPROM also holds the NBRN-modifiable setpoints, parameters and
time programmes but not the setpoints from the local operator panel of
the NRK16-B/A.
Construction
Essentially, the base unit consists of a metal housing and printed circuit
board.
The housing comprises a base and a cover, and accommodates the PCB and
two-part plug-in connection terminals. These terminals are accessible at the
top and bottom of the housing, so that peripheral devices can be connected
directly without removing the cover plate.
Additional terminals and a 10-pin ribbon cable connector are provided for
the power supply, operator terminal and R bus communication (see
page 5, Connection diagram and suitable devices).
The cover plate incorporates an aperture for the plug-in application mod-
ule, a rotary switch for setting the R bus address and three LEDs:
 Green (power): Power supply / basic test (on = OK)
 Yellow (Tx R ): Normal operation / R bus communication
(flashing = OK)
 Red (error) Error
The NRK16-B/A incorporates additional elements for control and display
(see page 8).
Note:
SAPIM (St uctu e and Pa amete Identifica-
tion Menu) is a p og amming language
developed by Landis & Staefa fo the
p og amming of cont ol and inte lock
modules. It consists of a wide ange of
basic functions (softwa e modules) which
can be combined to c eate all the
st uctu es equi ed.
92.00157

INTEGRAL RSA K21-04.10
4/8
Application controllers en - 06.2001
Siemens Building Technologies Landis & Staefa Division
Mounting and dimensions [mm]
The base unit can be fixed with four screws directly onto any surface, or
snap-mounted on two rails.
If mounting rails are used, proceed as follows:
1. Fix the top rail
2. Fit the bottom rail to the base unit and snap-mount the unit onto the
top rail
3. Fix the bottom rail
The terminal connections are grouped in blocks, making for easy wiring
without the need to remove the unit cover.
243
92.00156
125
149
Caution:
The application module is a static-
sensitive component.
Before inserting or removing the mo-
dule, the base unit must be discon-
nected from the po er supply.
Do not touch the contact pins in the
base unit.
252
52
162
59
49
24
15
203
92.00158
Opening the controller
1. Ensure that the necessary EMC precautions have been taken.
2. Undo the four cross-head screws between the terminal blocks.
3. Carefully lift off the cover.
For the NRK16-B/A: Press the four white plastic clips together with pliers,
carefully release the pcb for the display and operating unit, and pull
upwards.
Observe similar precautions when re-assembling the controller, paying
special attention to the fibre optic cables of the LEDs and the extension of
switch 100.
Caution:
Do not touch the PCB. Electronic
components can be damaged by
electrostatic discharge. Handling the
PCB ithout observing electrostatic
precautions ill invalidate the
arranty.

INTEGRAL RSA K21-04.10
5/8
Application controllers en - 06.2001
Siemens Building Technologies Landis & Staefa Division
Connection diagram and suitable peripheral devices
Notes:
1. The digital outputs (C, D, E and F) a e
active-type outputs, DC 0 o 24 V
(max. 50 mA).
2. Outputs C and D may be used as both
digital and analogue outputs. The di-
gital (24 V) signal switchs on when the
analogue output is > 5 V, and off
when it is < 3 V.
3. Othe input and output types may be
connected via the NTIO adapte and
suitable input o output modules.
Suitable peripheral devices (examples) Documentation
T1/Ni1000 ensors with T1 or Ni1000 measuring elements Various
ZM100/A Teminal housing for DC 0 ... 10 V valves CA2N4591
NTIO ingle terminal module carrier K21-06.50
NATU Adapter for special signals K21-06.52
NMID Multiplexer (to increase the number of digital inputs) K21-06.55
Room operating units, see page 7
-
1+
2
A
UI01
-
1+
2
B
UI02
-
1+
2
C
UI03
-
1+
2
D
UI04
-
1+
2
E
UI05
-
1+
2
F
UI06
-
1+
2
G
UI07
-
1+
2
H
UI08
-
1+
2
I
UI09
-
1+
2
J
UI10
-
1+
2K
UI11
+
4+ 6
UO07
3
-4
+
UO01
UO02
UO03
UO04
A B E
UO05
F
UO06
3
-4
+3
-5
+3
-5
+
3
-4
+5 +3
-4
+5 +
AC
24 V DC 15 V
TE L
(+) N
(-)
GND
+15
92.00160en
3 = COMMON
4 = DC 0 ... 10 V
5 = digital (DC 0 / 24 V)
-
+
+15
GND
NMID
C D
3
ZM100
4
Service
34 3 5
Relay, 24 VDC
NBRN
(RS485)
12 12 12 12
GND
+15
DC 0 ... 10 VdigitalT1 Remote
control
SAPIM I/O number
SAPIM I/O number
1 2
AC 24 V
L
SN S
T1/Ni1000

INTEGRAL RSA K21-04.10
6/8
Application controllers en - 06.2001
Siemens Building Technologies Landis & Staefa Division
00414
S182
D120
D140
OFF
ON
21
ON
Selection of T or Ni 000 sensor
Both T1 and Ni1000 sensors can be connected to the R A application
controllers. DIP switch 182 is used to adapt the controller to the required
sensor type. External access to this DIP switch is possible after removal of
the N A plug-in application module. The change-over from one sensor type
to the other is applied in blocks of eight and three inputs (UI01...UI08 and
UI09...UI11 respectively).
Rotary address
switch
T1/Ni1000
switch
Firmware
Battery
Application
Slot for NSA
module
Disabling the sensor supply voltage
The pull-up resistors (Ri = 10kW) for the T1 and Ni1000 sensor supply volt-
age can be disabled individually at inputs A (UI101) to J (UI10) with jumpers
X310 to X420. This process is required whenever devices are connected
which are unable to sink current.
The jumpers are located on the printed circuit board and cannot be adjusted
without opening the controller housing.
When delivered from the factory, the jumper settings are such that the sensor
supply voltage is enabled. To disable the supply, each jumper must be
moved one position to the left.
Settings for switch S 82 T /Ni 000
1 2 ensor Inputs
OFF T1 UI01 to UI08
OFF T1 UI09 to UI16
ON Ni1000 1) UI01 to UI08
ON Ni1000 1) UI09 to UI16
The factory setting is T1
1) When setting the input pa amete s in
INTEGRAL PLAN, note that the T1 input
ange should be used fo Ni1000
senso s. The cont olle is adapted to the
senso via the ha dwa e only. The
SAPIM softwa e is not affected.
Inputs and jumpers
Input Jumpe Input Jumpe
A UI01 X310 F UI06 X360
B UI02 X320 G UI07 X370
C UI03 X330 H UI08 X380
D UI04 X340 I UI09 X410
E UI05 X350 J UI10 X420
Caution
The incorrect positioning of jumpers
can give rise to offset voltages hen
active signal transmitters are connec-
ted (failure to reach a zero-point).
View of part of the PCB: In this example, apart from X 50 and X 60 (T1/Ni1000 supply
OFF) all the jumpers are shown in their factory-set position.
51068A
X310 X320 X330 X340
X350
X360 X370 X380 X410 X420
X301 X302
UI01 ... UI05 UI06 ... UI10

INTEGRAL RSA K21-04.10
7/8
Application controllers en - 06.2001
Siemens Building Technologies Landis & Staefa Division
Operation and service
The controller can be operated by various means:
 Remotely, from a room operating unit
 Via the R bus, with an operator terminal or PC
 NBRN-.. operator terminal or service PC for service and commissioning
 NRK16-B/A for simple local operation (see page 8)
 NRK16-WEB/A for operation with an Internet browser
Remote operation
Connection terminals K1, K2, K4 and K6 are provided for remote operation
from a type KR.. room operating unit. The PB.. operating units should be
connected to universal inputs A..J.
Suitable room operating units Documentation
KRT-1B Room temperature measurement
Room temperature setpoint adjustment
Mode selection (AUT, ON or OFF)
Heating time extension (by 1, 2 or 4 hours) CA2N1612
KRT-1L Room temperature measurement
Room temperature setpoint adjustment
Mode selection (AUT, ON or OFF)
Holiday mode extension (by 1, 2 or 3 days) CA2N1613
KRU-1 Room temperature measurement
Mode selection (AUT, ON or OFF)
Timer module with independent time function CA2N1614
PBA Room temperature measurement
Room temperature setpoint adjustment CA2N1651
P B C Room temperature measurement
Room temperature setpoint adjustment
Digital display of room temperature CA2N1655
See the relevant documentation for maximum cable lengths
Operation via RS bus
ince the controller is compatible with the R bus, it can be operated
remotely from any of the following devices:
 NBE remote operator terminal (see K21-05.18)
 NBRN-.. operator terminal (see K21-05.10 and 12)
 From a PC running the INTEGRAL DIALOG service software, connected
via the NITEL.. communications module (see K21-07.30) or NARC
R 485-R 232 adapter
 Internet browser, via the NIWEB communications module
Where the INTEGRAL R system is integrated into a higher-level
system, the controllers can also be operated as follows:
 In an INTEGRAL M 1000, M 2000 or T 1500 building
management system
 In the DE IGO IN IGHT building management system, with advanced
graphics-based operation
Service and commissioning
For service and commissioning purposes an NBRN-.. terminal or a PC can
be connected directly to the service socket on the controller. The same
socket is used to download an application-specific APIM program from a
suitable PC (not required for pre-programmed modules).
User manuals
The following user manuals are available for the operator software
described above:
 K23 NBRN.. operator terminals
 K9 INTEGRAL DIALOG
 CA12U3290 NIWEB User manual
 CA1B9110 DE IGO IN IGHT
Important:
For communication on the RS bus,
the controller must be assigned the
appropriate address, by use of the
rotary s itch on the cover plate.
(Factory-setting: Address 1).

INTEGRAL RSA K21-04.10
8/8
Application controllers en - 06.2001
Siemens Building Technologies Landis & Staefa Division
92.00159
123
54
Simple local operation with the NRK16-B/A
The cover plate of the NRK16-B/A incorporates facilities for direct opera-
tion. The functions of the selectable display and switches are defined by
the application module selected.
1 Rocke switches
2 Fou -digit 7-segment LED display
3 Display-selecto keys, f om top:
 Measu ed value 1
 Measu ed value 2
 Setpoint 1
 Setpoint 2
4 Channel LEDs
co esponding to selecto keys
5<+> and <> fo setpoint ent y
Each rocker switch has three positions with functions which vary depending
on the application module used. The allocation of the two setpoints and
two measured values also depends on the application. These four values
can be displayed in the four-digit LED display panel by use of the appropri-
ate selector key. The setpoints can be modified with the <+> and <> keys;
these also operate as repeating keys when continuously depressed. Each of
the four values is associated with one of the red channel LEDs. With some
applications, the setpoints can have upper and lower limits, adjustable
from an operator terminal.
LED unction test
Depressing the two lower selector keys simultaneously should cause all seg-
ments of the display panel and the channel LEDs to light up..
Alarm handling
ubject to the application selected, the display panel can also be used to in-
dicate alarms. A code between A1 and A9 can be displayed (A1A8 for
alarms defined in accordance with the application, and A9 for a common
alarm). The operation of the controller is not affected by the presence of an
alarm. While the measured value or setpoint is displayed, the associated
channel LED will flash, i.e. the alarm remains active. The alarm code can be
displayed again by pressing the two upper selector keys simultaneously.