Siemens SIMATIC IPC1047 User manual

SIMATIC IPC1047
SIMATIC
Industrial PC
SIMATIC IPC1047
Operating Instructions
07/2019
A5E45118479
-AB
Preface
Overview
1
Safety Instructions
2
Installing and connecting the
device
3
Commissioning the device
4
Operating the device
5
Expanding and assigning
parameters to the device
6
Device maintenance and
repair
7
Technical specifications
8
Dimension drawings
9
Standards and approvals
10
Technical support
A
Markings and symbols
B
Abbreviations
C

Siemens AG
Division Digital Factory
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E45118479-AB
Ⓟ
07/2019 Subject to change
Copyright © Siemens AG 2019.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

SIMATIC IPC1047
Operating Instructions, 07/2019, A5E45118479-AB 3
Preface
These operating instructions contain all the information you need for commissioning and
operation of the SIMATIC IPC1047.
It is intended both for programming and testing personnel who commission the device and
connect it with other units (automation systems, programming devices), as well as for service
and maintenance personnel who install add-ons or carry out fault/error analyses.
Basic knowledge required
A solid background in electrical installation, personal computers, Microsoft operating
systems and network technology is required to understand this manual.
Validity of the Operating Instructions
These operating instructions are valid for all supplied versions of the SIMATIC IPC1047.
Scope of this documentation
The documentation for the SIMATIC IPC1047 includes:
●Product Information "Important notes on your device"
●Quick Install Guide
●Operating instructions in German, English and French
Refer to the corresponding user documentation for information and instructions on using
software.
Conventions
The following naming conventions apply in these operating instructions:
●The terms "Industrial PC", "PC" or "device" are also used in place of the product name
"SIMATIC IPC1047".
●The abbreviation "Microsoft Windows" or "Windows" is also used in place of the brand
name Microsoft® Windows®.
History
Currently released versions of these operating instructions:
Version
Comments
09/2018 First edition
07/2019 New edition, description of configurable device features added, security provi-
sions revised in accordance with IEC/EN/UL 61010-2-201

Preface
SIMATIC IPC1047
4Operating Instructions, 07/2019, A5E45118479-AB
Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be
connected to an enterprise network or the internet if and to the extent such a connection is
necessary and only when appropriate security measures (e.g. firewalls and/or network
segmentation) are in place.
For additional information on industrial security measures that may be implemented, please
visit (http://www.siemens.com/industrialsecurity).
Siemens' products and solutions undergo continuous development to make them more
secure. Siemens strongly recommends that product updates are applied as soon as they are
available and that the latest product versions are used. Use of product versions that are no
longer supported, and failure to apply the latest updates may increase customers' exposure
to cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed visit (http://www.siemens.com/industrialsecurity).
Disclaimer for third-party software updates
This product includes third-party software. Siemens AG only provides a warranty for
updates/patches of the third-party software, if these have been distributed as part of a
Siemens software update service contract or officially released by Siemens AG. Otherwise,
updates/patches are undertaken at your own risk. You can find more information about our
Software Update Service offer on the Internet at Software Update Service
(http://www.automation.siemens.com/mcms/automation-software/en/software-update-
service).
NOTICE
Danger for machine and plant through unauthorized remote access
IPMI remote monitoring has a known standard password in the delivery state. This allows
unauthorized access to the device from the outside by third parties. Damage to the
machine or plant is not excluded.
•Change the IPMI password immediately after commissioning the device. You can find
additional information in the sections "Monitoring functions (Page 51)" and "IPMI Setup
(Page 99)".
•Alternatively, do not connect IPMI-enabled devices to the Internet or any network at all.

SIMATIC IPC1047
Operating Instructions, 07/2019, A5E45118479-AB 5
Table of contents
Preface ................................................................................................................................................... 3
1 Overview................................................................................................................................................. 9
1.1 Product description ...................................................................................................................9
1.1.1 Overview ...................................................................................................................................9
1.1.2 Scope of application..................................................................................................................9
1.1.3 Highlights ................................................................................................................................10
1.1.4 Features..................................................................................................................................11
1.2 Design of the device ...............................................................................................................13
1.2.1 Front panel..............................................................................................................................13
1.2.2 Rear of the device...................................................................................................................14
1.2.3 Interfaces at rear of the device ...............................................................................................15
1.2.4 Status displays........................................................................................................................16
1.2.4.1 System status displays ...........................................................................................................16
1.2.4.2 Power indicators, redundant power supply.............................................................................17
1.2.4.3 Status displays on removable tray for drives ..........................................................................19
1.3 Accessories and spare parts ..................................................................................................20
2 Safety Instructions ................................................................................................................................ 21
2.1 General safety instructions .....................................................................................................21
2.2 Notes on ambient and environmental conditions....................................................................26
3 Installing and connecting the device ...................................................................................................... 29
3.1 Preparing for installation .........................................................................................................29
3.1.1 Checking the delivery package...............................................................................................29
3.1.2 Identification data of the device ..............................................................................................29
3.1.3 Permitted mounting positions .................................................................................................30
3.2 Mounting the device................................................................................................................31
3.2.1 Installation guidelines..............................................................................................................31
3.2.2 Mounting the device................................................................................................................32
3.3 Connecting the device ............................................................................................................33
3.3.1 Country-specific information on supply voltage ......................................................................33
3.3.2 Connecting the power supply .................................................................................................34
3.3.2.1 Information about the power supply........................................................................................34
3.3.2.2 Connecting a single power supply ..........................................................................................34
3.3.2.3 Connecting a redundant power supply ...................................................................................35
3.3.3 Connecting I/O devices...........................................................................................................36
4 Commissioning the device .................................................................................................................... 37
4.1 General information on commissioning ..................................................................................37
4.2 Switching on the device ..........................................................................................................38
4.3 Automatic switching on of the device......................................................................................39
4.4 Switching off the device ..........................................................................................................39

Table of contents
SIMATIC IPC1047
6Operating Instructions, 07/2019, A5E45118479-AB
5 Operating the device............................................................................................................................. 41
5.1 Opening the front door ........................................................................................................... 41
5.2 Drive configurations ............................................................................................................... 41
5.2.1 Multi-disk system.................................................................................................................... 41
5.2.2 RAID systems ........................................................................................................................ 42
5.2.2.1 Manage RAID system ............................................................................................................ 42
5.2.2.2 RAID system of the motherboard........................................................................................... 43
5.2.2.3 SAS/SATA hardware RAID system ....................................................................................... 43
5.2.2.4 RAID1 system ........................................................................................................................ 45
5.3 Operating RAID systems ....................................................................................................... 46
5.3.1 Manage onboard RAID system.............................................................................................. 46
5.3.1.1 Example for a RAID1 system during the boot phase of the system ...................................... 46
5.3.1.2 RAID software ........................................................................................................................ 47
5.3.1.3 Checking the status of the RAID system ............................................................................... 47
5.3.1.4 Displaying a defective hard disk of a RAID system in the RAID software ............................. 48
5.3.1.5 Special feature: Replacing hard disk in the RAID system when switched off ....................... 48
5.3.1.6 Integrating a new hard disk drive in the RAID system........................................................... 49
5.3.2 Managing the Hardware RAID system .................................................................................. 50
5.4 Monitoring functions............................................................................................................... 51
5.5 Trusted Platform Module (TPM)............................................................................................. 52
6 Expanding and assigning parameters to the device............................................................................... 53
6.1 Open the device. .................................................................................................................... 53
6.2 Drives ..................................................................................................................................... 54
6.2.1 Overview ................................................................................................................................ 54
6.2.2 Drives in drive cage type A .................................................................................................... 56
6.2.2.1 Change 2.5" and 3.5" drive in removable tray ....................................................................... 56
6.2.2.2 Installing a 5.25" adapter module for removable trays .......................................................... 58
6.2.2.3 Installing a backplane for removable tray .............................................................................. 59
6.2.2.4 Changing a backplane for removable tray ............................................................................. 61
6.2.3 Drives in drive cage type B .................................................................................................... 63
6.2.3.1 Overview ................................................................................................................................ 63
6.2.3.2 Removing and installing a tray from/in the drive cage ........................................................... 65
6.2.3.3 Removing and installing 3.5" drives from/in tray.................................................................... 66
6.2.3.4 Removing and installing 2.5" drives from/in tray.................................................................... 67
6.2.4 Replacing a defective hard disk drive in the RAID system .................................................... 70
6.3 Expansion cards..................................................................................................................... 71
6.3.1 Notes on the expansion cards ............................................................................................... 71
6.3.2 Configuration variants ............................................................................................................ 72
6.3.3 Installing and removing expansion cards............................................................................... 73
6.3.4 Installing the PCI expansion kit (optional).............................................................................. 74
6.3.5 Removing and installing the graphics card ............................................................................ 76
6.3.6 Installing and configuring the hardware RAID adapter card .................................................. 78
6.4 Installing a second COM interface (optional)......................................................................... 80

Table of contents
SIMATIC IPC1047
Operating Instructions, 07/2019, A5E45118479-AB 7
7 Device maintenance and repair............................................................................................................. 81
7.1 Repair information...................................................................................................................81
7.2 Maintenance intervals.............................................................................................................82
7.3 Removing and installing hardware..........................................................................................82
7.3.1 Remove the fan cover.............................................................................................................82
7.3.2 Replacing filters ......................................................................................................................83
7.3.3 Replacing device fans.............................................................................................................83
7.3.4 Change the fan on drive cage type A .....................................................................................85
7.3.5 Replacing the backup battery .................................................................................................87
7.3.6 Replacing the redundant power supply module .....................................................................89
7.3.7 Replacing the processor .........................................................................................................90
7.4 Installing the software .............................................................................................................91
7.4.1 Back-up authorization or license key ......................................................................................91
7.4.2 Restoring the factory settings of the operating system and partitions (Restore)....................92
7.4.3 Updating the operating system ...............................................................................................93
7.4.4 Installing drivers and software ................................................................................................94
7.4.5 Installing Windows (Recovery) ...............................................................................................94
7.4.6 Installing Hardware RAID controller software.........................................................................98
7.5 BIOS description .....................................................................................................................99
7.6 IPMI Setup ..............................................................................................................................99
7.7 Recycling and disposal .........................................................................................................100
8 Technical specifications ...................................................................................................................... 101
8.1 General specifications...........................................................................................................101
8.2 Current and power requirements ..........................................................................................105
8.3 Power supply (AC) ................................................................................................................106
8.4 AC power supply, redundant ................................................................................................107
8.5 Motherboard..........................................................................................................................108
9 Dimension drawings............................................................................................................................ 109
9.1 Dimensional drawing of the device .......................................................................................109
9.2 Dimension drawing for telescope rails..................................................................................110
9.3 Dimension drawing of the expansion cards..........................................................................110
10 Standards and approvals .................................................................................................................... 111
A Technical support................................................................................................................................ 113
A.1 Service and support ..............................................................................................................113
A.2 Troubleshooting ....................................................................................................................114
A.2.1 Problems with device functions ............................................................................................114
A.2.2 Problems with the RAID system and device startup.............................................................115
A.2.3 Problems when using expansion cards ................................................................................116

Table of contents
SIMATIC IPC1047
8Operating Instructions, 07/2019, A5E45118479-AB
B Markings and symbols .........................................................................................................................117
B.1 Overview .............................................................................................................................. 117
B.2 Safety ................................................................................................................................... 117
B.3 Operator controls ................................................................................................................. 118
B.4 Certificates, approvals and markings................................................................................... 117
B.5 Interfaces ............................................................................................................................. 118
C Abbreviations.......................................................................................................................................119
Glossary ..............................................................................................................................................125
Index ...................................................................................................................................................133

SIMATIC IPC1047
Operating Instructions, 07/2019, A5E45118479-AB 9
Overview
1
1.1 Product description
1.1.1 Overview
The SIMATIC IPC1047 is a high-performance rack PC with industrial functionality:
●Highly compact
●Extremely rugged
●Extensive product continuity
Note
Depending on the configuration ordered, the features and illustrations described in this
manual may differ from the features of your d
evice.
1.1.2 Scope of application
The device offers very high computing power in a compact enclosure for 19" rack installation.
It has a high degree of flexible expandability for diverse performance-driven applications:
●Scientific calculations and simulations
●Image processing and editing
●Cryptography
●Process monitoring
●Virtualization
●Quality assurance
●Scada applications
●Artificial intelligence, machine learning

Overview
1.1 Product description
SIMATIC IPC1047
10 Operating Instructions, 07/2019, A5E45118479-AB
1.1.3 Highlights
Performance optimized to the application
●High computing and graphics performance
●Use of suitable drives and memory
High level of functionality and ease of service
●High availability through redundancy and optimized cooling
●Rack design for easy installation
Use in a rugged environment
●Extended temperature range
●Dust exposure, shock and vibration
High investment protection
●High continuity of the components/design
●Product availability up to 5 years
●Repair service for additional 5 years
High system availability
●ECC memory modules
●Redundant power supply (optional)
●Integration of redundant or high-performance SAS/SATA/RAID data systems with
additional controller card (optional)
●Hardware RAID
–Auto-Rebuild for change of hard disk
–"Zero-Maintenance Cache Protection" protects the data in the hardware RAID
controller cache in the event of a power failure
–Reduced load on the main processor during the rebuild
–Fast HDDs/SSDs for high speed when reading and writing data

Overview
1.1 Product description
SIMATIC IPC1047
Operating Instructions, 07/2019, A5E45118479-AB 11
1.1.4 Features
General features
Design •19" rack, 4 HU, 572 mm enclosure depth
•Rugged bay enclosure
•Prepared for mounting telescopic rails
•Can be mounted horizontally
•
Lockable enclosure front
Motherboard Dual socket R3 (LGA 2011-3) supports Intel® Xeon® processor E5-v3/v4
generation
CPU Dual Intel® Xeon® E5-26xx series,
from 1.7 GHz/8 cores to 2.3 GHz/14 cores
Main memory configu-
ration
Up to 512 GB DDR4 RAM 2400 MHz
(more memory available as an option on request)
Hard disk space
Up to 16 TB
Drive bays
Up to 4 × 3.5" or 8 x 2.5"´drive in internal drive cage or in removable drive bay
Expansion card slots •3 × PCIe x8
•
3 × PCIe x16
Power supply •Single power supply
100 … 240 V AC (-10%; +10%), wide-range
13–7 A, 47–63 Hz, 860 watts or
•Redundant power supply
2 x 100 … 240 V AC (-10%; +10%), wide-range
10–5 A, 60–50 Hz, 700 watts
Interfaces
Ethernet •2 × 1 Gbps (INTEL I350)
•1 × RJ45 IPMI LAN
See section "Monitoring functions (Page 51)"
USB •2 × USB 3.0 (front)
•2 × USB 3.0 (rear)
•2 × USB 2.0 (rear)
Serial •1 × COM port (rear)
•
1 × COM port (rear, optional)
Monitor
1 × VGA, optional Nvidia Quadro Px expansion card
TPM
1 × TPM 1.2 20-pin header
Monitoring functions
Voltages
Voltage monitoring for motherboard, CPU, memory
Temperatures Temperature monitoring of CPU, memory, HDD, mainboard with corre-
sponding closed-loop control of fan speeds
LED •POWER (internal power supply present, PC switched on)
•HDD (access to hard disk)
•FAN FAIL (display fan problems)
Power supply status,
power, temperatures,
voltages
Monitoring of redundant power supply (optional)

Overview
1.1 Product description
SIMATIC IPC1047
12 Operating Instructions, 07/2019, A5E45118479-AB
Operating systems
Operating system for
order, pre-installed
Microsoft® Windows® 10 Enterprise 2016 LTSB, 64-bit, multi-language 1
Operating system for
order, license and
drivers, not pre-
installed
Microsoft® Windows® Server 2016 Standard Edition incl. 5 Clients, 64-bit,
multi-language 1
(additional licenses possible as an option on request)
Alternative: without
operating system
Compatibility with the motherboard
1 Multi-language user interface MUI: 5 languages (English, German, French, Spanish, Italian)
Optional accessories
DOM
2 × SuperDOM (Disk on Module)
PCI expansion card
Can be mounted crosswise as complete PCI expansion kit
PCI graphics card •NVIDIA Quadro P400, 64-bit, 2 GB GDDR5 RAM, 4 × Mini DisplayPort,
resolution: 3 × 4096×2160 @ 60 Hz, 1 × 5120×2880 @ 60 Hz
•NVIDIA Quadro P1000, 128-bit, 4 GB GDDR5 RAM,
4 × Mini DisplayPort, resolution: 4 × 4096×2160 @ 60 Hz,
4 × 5120×2880 @ 60 Hz
•NVIDIA Quadro P4000, 256-bit, 8 GB GDDR5 RAM, 4 × DisplayPort,
resolution: 4 × 4096×2160 @ 120 Hz, 4 × 5120×2880 @ 60 Hz
•NVIDIA Quadro P5000, 256-bit, 16 GB GDDR5X RAM, 4 × DisplayPort,
resolution: 4 × 7680×4320 @ 30 Hz, 4 × 2560×1600 @ 60 Hz
PCI hardware RAID
controller
•Adaptec RAID 8405 PCIe 3.0 x8 with:
–4 SAS/SATA ports
–CPU and cache memory, therefore negligible effect on the system
–Backup for data reliability in the event of power failures
•Adaptec RAID 8805 PCIe 3.0 x8 with:
–8 SAS/SATA ports
–CPU and cache memory, therefore negligible effect on the system
–Backup for data reliability in the event of power failures
LAN expansion card •Intel® I350-T2, 2 × 1 GB LAN
•Intel® I350-T4, 4 × 1 GB LAN
•Intel® X540-T2, 2 × 10 GB LAN

Overview
1.2 Design of the device
SIMATIC IPC1047
Operating Instructions, 07/2019, A5E45118479-AB 13
1.2 Design of the device
1.2.1 Front panel
Front view
①
19" mounting bracket
②
Fan cover on front fan with ventilation openings, locked by front door
③
System status displays (Page 16)
④
Front door: lockable, protection against unauthorized access
⑤
Lock
•Key vertical: open
•Key horizontal: closed
View with front door open
The following figures show examples of devices with front door open. Depending on the
configuration, the device is equipped with one of the following drive cages:
●Drive cage type A with slots for removable drives
The removable trays can be locked; this way, the drives are protected from unauthorized
access.
●Drive cage type B with fixed slots for drives

Overview
1.2 Design of the device
SIMATIC IPC1047
14 Operating Instructions, 07/2019, A5E45118479-AB
①
USB 3.0 ports
②
Reset button
③
On/off button
④
Captive locking screw of the enclosure cover
⑤
Slots for removable drives in drive cage type A
⑥
Slot covers for drives in drive cage type B
1.2.2 Rear of the device
Rear view with AC power supply
①
ATX power supply
⑤
Interfaces
②
Power LED
⑥
Expansion card slots
③
On/off switch
⑦
PCI expansion kit interface (optional)
④
Power connection socket
⑧
2nd COM interface (optional)

Overview
1.2 Design of the device
SIMATIC IPC1047
Operating Instructions, 07/2019, A5E45118479-AB 15
Rear view with redundant AC power supply
①
Power connection socket
⑤
Interfaces
②
Acknowledgment button with status LED
⑥
Expansion card slots
③
Power supply module
⑦
PCI expansion kit interface (optional)
④
Handle
⑧
2nd COM interface (optional)
1.2.3 Interfaces at rear of the device
①
COM interface
②
RJ45 IPMI dedicated LAN connection
③
USB 2.0 ports
④
USB 3.0 ports
⑤
Gbit ETHERNET interface 1
⑥
Gbit ETHERNET interface 2
⑦
VGA connection

Overview
1.2 Design of the device
SIMATIC IPC1047
16 Operating Instructions, 07/2019, A5E45118479-AB
1.2.4 Status displays
1.2.4.1 System status displays
Front status displays
The status displays provide information on the status of the device components listed in the
following table. The operating indicators are visible when the front door is closed and open.
①
"POWER" LED
②
"HDD" LED
③
"FAN FAIL" LED
Meaning of the LEDs
LED
Meaning
LED status
Meaning of the status
POWER Operating mode of the PC
OFF
Switched off or disconnected from the mains
YELLOW Idle state or shut down
GREEN
PC in operation
HDD Access to hard disk
OFF
No access
GREEN
Access
FAN FAIL Fan status
OFF
No error
RED flashing Possible causes:
•CPU heat sink fan fault
•Front fan faulty
•Power supply fan fault

Overview
1.2 Design of the device
SIMATIC IPC1047
Operating Instructions, 07/2019, A5E45118479-AB 17
Rear status displays
The Ethernet interfaces with the following status displays are located on the rear of the
device:
LED
Meaning
LED status
Meaning of the status
LED 1 1Connection status OFF •No cable connected
•Cable disabled
•Interface disabled
GREEN •Active cable connected
GREEN, flashing •Data transfer active
LED 2 1Data transmission rate OFF •10 Mbps
GREEN •100 Mbps
YELLOW •1000 Mbps
1
The Ethernet ports are numbered on the enclosure to identify them clearly. The numbering by the
operating system may deviate from this.
1.2.4.2 Power indicators, redundant power supply
Rear
The power supply unit of the redundant power supply consists of two power supply modules.
The power supply unit works as soon as one power supply module is in operation. If a power
supply module is out of service, a visual and audible warning signal sounds.
The following figure shows an example with power supply module ①in operation and power
supply module ②out of service.

Overview
1.2 Design of the device
SIMATIC IPC1047
18 Operating Instructions, 07/2019, A5E45118479-AB
LED
Meaning
LED status
Meaning of the status
LED of acknowl-
edgment
button 1
Operating sta-
tus of power
supply module 1
OFF
Device disconnected from power supply
Flashes
GREEN
•Power supply module 1 ready for operation
•PC switched off
GREEN •Power supply module 1 in operation
•PC switched on
Flashes RED
Power supply 1 interrupted
RED
Power supply module 1 defective
Flashes slowly
RED/GREEN
Warning at power supply module 1,
e.g. overload
LED of acknowl-
edgment
button 2
Operating sta-
tus of power
supply module 2
OFF Device disconnected from power supply
Flashes
GREEN
•Power supply module 2 ready for operation
•PC switched off
GREEN •Power supply module 2 in operation
•PC switched on
Flashes RED
Power supply 2 interrupted
RED
Power supply module 2 defective
Flashes slowly
RED/GREEN
Warning at power supply module 2,
e.g. overload

Overview
1.2 Design of the device
SIMATIC IPC1047
Operating Instructions, 07/2019, A5E45118479-AB 19
1.2.4.3 Status displays on removable tray for drives
The following figure shows the status displays of a removable tray in devices with drive cage
type A.
①
"Power" LED
②
"Activity" LED
Meaning of the LEDs
LED
Meaning
LED status
Meaning of the status
Power Status of the removable tray OFF •Device switched off
•Power supply not connected
•No drive installed
Lit •Device is switched on and a drive is
installed
Activity Status of the drive Flashes •Drive is active
OFF •Drive is not active

Overview
1.3 Accessories and spare parts
SIMATIC IPC1047
20 Operating Instructions, 07/2019, A5E45118479-AB
1.3 Accessories and spare parts
Accessories from Siemens are available for your device. These are not included in the scope
of delivery.
Obtaining accessories from the SIEMENS Industry Mall
You can find additional information in the online ordering system Industry Mall
(https://mall.industry.siemens.com).
Accessories available for order
Name
Description
Article number
Low profile remova-
ble rack unit
The removable tray makes for quick and simple
replacement of a 2.5" or 3.5" drive without hav-
ing to open the device or remove it from the
control cabinet. The result is the following ad-
vantages for service and maintenance, data
backup and data transfer:
•Replacement of a failed hard disk in opera-
tion ("hot-swap")
•Downloading different system states or op-
erating systems from different hard drives
during a short period of time.
•Simplified data backup by copying, for ex-
ample, to a backup hard drive.
•Simple transportation of backup data
•Separate data storage and archiving possi-
ble
6ES7648-0EH00-1BA0
PCI expansion kit
Riser card with slot for PCI expansion card
6BK1700-6HA70-0AA0
Filter pad Filter pad for fan cover on the device front,
package with 10 filter pads
A5E37019277
Device fan
Internal fan
6BK1700-6HA71-0AA0
Backup battery The battery is used to back up the CMOS data
for the BIOS setup and the real-time clock.
6BK1700-6HA73-0AA0
Restore USB stick
Windows 10
USB stick for restoring the delivery state of the
operating system, drivers and partitioning
A5E47323540
USB stick Windows
Server 2016
USB stick for restoring the operating system A5E47932416
SIEMENS spare parts services
Information on ordering, the provision and delivery of spare parts can be found under
"Industry Online Support: Spare parts services
(http://support.automation.siemens.com/WW/view/en/16611927)".