Siemens SIMATIC IPC427E User manual

___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
SIMATIC
Industrial PC
SIMATIC IPC427E
Operating Instructions
09/2017
A5E37454814
-AB
Preface
Overview
1
Safety Instructions
2
Installing and connecting the
device
3
Commissioning the device
4
Extended device functions
5
Expanding and assigning
parameters to the device
6
Device maintenance and
repair
7
Technical specifications
8
Technical support
A
Markings and symbols
B
List of abbreviations
C

Siemens AG
Division Digital Factory
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E37454814-AB
Ⓟ
09/2017 Subject to change
Copyright © Siemens AG 2017.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

SIMATIC IPC427E
Operating Instructions, 09/2017, A5E37454814-AB 3
Preface
Purpose of the Operating Instructions
These operating instructions contain all the information you need for commissioning and
operating the SIMATIC IPC427E.
It is intended both for programming and testing personnel who commission the device and
connect it with other units (automation systems, programming devices), as well as for service
and maintenance personnel who install add-ons or carry out fault/error analyses.
Basic knowledge required
A solid background in personal computers and Microsoft operating systems is required to
understand this manual. General knowledge in the field automation control engineering is
recommended.
Scope of the operating instructions
These operating instructions are valid for all versions of the SIMATIC IPC427E.
Approbations
You will find additional information in "Certificates and approvals (Page 95)".
CE marking
You will find additional information in "Certificates and approvals (Page 95)".
Standards
For more information, refer to sections "Certificates and approvals (Page 95)" and
"Technical specifications (Page 105)".
Position in the information landscape
The IPC documentation comprises:
●SIMATIC IPC427E Quick Install Guide with product information about the device, for
example important notes
●SIMATIC IPC427E Operating Instructions
The documentation is supplied with the IPC in multiple languages in electronic form as a
PDF file on the USB stick supplied in the documentation package.

Preface
SIMATIC IPC427E
4Operating Instructions, 09/2017, A5E37454814-AB
Conventions
The terms "PC" and "device" are sometimes used to refer to the SIMATIC IPC427E in this
documentation.
The term "Windows Embedded Standard" is used throughout to refer to "Windows
Embedded Standard 7". "Windows 7" is used as an abbreviation for "Windows 7 Ultimate".
Note
A n
ote is important information about the product, handling the product or a reference to
specific sections of the documentation that require special consideration.
History
The following editions of these operating instructions have already been published:
Edition
Comments
09/2016
First edition
09/2017 Amendment regarding Windows 10
Corrections

SIMATIC IPC427E
Operating Instructions, 09/2017, A5E37454814-AB 5
Table of contents
Preface ................................................................................................................................................... 3
1 Overview................................................................................................................................................. 9
1.1 Product description ...................................................................................................................9
1.1.1 Applications.............................................................................................................................10
1.1.2 Features..................................................................................................................................10
1.2 Design of the device ...............................................................................................................13
1.2.1 Interfaces and operating elements .........................................................................................13
1.2.2 Status displays........................................................................................................................14
1.3 Accessories.............................................................................................................................15
2 Safety Instructions ................................................................................................................................ 17
2.1 General safety instructions .....................................................................................................17
2.2 Notes on usage.......................................................................................................................21
3 Installing and connecting the device ...................................................................................................... 23
3.1 Preparing for installation .........................................................................................................23
3.1.1 Checking the delivery package...............................................................................................23
3.1.2 Identification data of the device ..............................................................................................25
3.1.3 Permitted mounting positions .................................................................................................27
3.2 Installing the device ................................................................................................................29
3.2.1 Mounting instructions..............................................................................................................29
3.2.2 Installation on a DIN rail..........................................................................................................31
3.2.2.1 Attaching the DIN rail bracket .................................................................................................31
3.2.2.2 Mounting on DIN rails .............................................................................................................32
3.2.3 Wall mounting .........................................................................................................................33
3.2.4 Upright mounting.....................................................................................................................34
3.3 Connecting the device ............................................................................................................35
3.3.1 Notes on connecting ...............................................................................................................35
3.3.2 Connecting the protective conductor ......................................................................................37
3.3.3 Connecting peripheral equipment...........................................................................................38
3.3.4 Connecting expansion cards ..................................................................................................39
3.3.5 Connecting the terminal ..........................................................................................................40
3.3.6 Connecting the power supply .................................................................................................41
3.3.7 Connecting the device to networks.........................................................................................42
3.3.8 Installing the strain relief .........................................................................................................43
3.3.9 Securing the lines ...................................................................................................................44

Table of contents
SIMATIC IPC427E
6Operating Instructions, 09/2017, A5E37454814-AB
4 Commissioning the device .................................................................................................................... 45
4.1 General information on commissioning ................................................................................. 45
4.2 Initial commissioning.............................................................................................................. 47
4.3 Windows Action Center.......................................................................................................... 48
4.4 IPC Driver and Tools.............................................................................................................. 48
5 Extended device functions .................................................................................................................... 49
5.1 Monitoring Functions.............................................................................................................. 49
5.1.1 Overview of the monitoring functions..................................................................................... 49
5.1.2 Temperature monitoring/display ............................................................................................ 50
5.1.3 Watchdog (WD)...................................................................................................................... 51
5.1.4 Battery monitoring .................................................................................................................. 52
5.1.5 Mass storage monitoring........................................................................................................ 52
5.2 Unified Write Filter (UWF)...................................................................................................... 52
5.3 Enhanced Write Filter (EWF) ................................................................................................. 53
5.4 File Based Write Filter (FBWF).............................................................................................. 56
5.5 Buffer memory NVRAM ......................................................................................................... 58
5.6 Operation without monitor and keyboard............................................................................... 58
5.7 Active Management Technology (AMT) ................................................................................ 58
5.8 Trusted Platform Modul (TPM)............................................................................................... 60
6 Expanding and assigning parameters to the device............................................................................... 61
6.1 Installing and removing the memory module ......................................................................... 61
6.1.1 Opening the device ................................................................................................................ 61
6.1.2 Opening the device containing expansion cards ................................................................... 63
6.1.3 Replacing memory modules .................................................................................................. 64
6.2 Installing and removing CFast cards...................................................................................... 66
6.3 Installing and removing PCIe cards ....................................................................................... 68
6.4 Assigning CPU power consumption parameters ................................................................... 71
7 Device maintenance and repair............................................................................................................. 73
7.1 Maintenance........................................................................................................................... 73
7.2 Repair information.................................................................................................................. 73
7.3 Installing and removing hardware .......................................................................................... 76
7.3.1 Installing and removing the backup battery ........................................................................... 76
7.3.2 Changing storage media........................................................................................................ 78
7.3.2.1 Replacing a HDD/SSD........................................................................................................... 78
7.4 Installing the software ............................................................................................................ 81
7.4.1 Reinstalling the operating system .......................................................................................... 81
7.4.1.1 General installation procedure ............................................................................................... 81
7.4.1.2 Restoring the factory state ..................................................................................................... 83
7.4.1.3 Windows 7 / Windows 10....................................................................................................... 84
7.4.1.4 Windows Embedded Standard .............................................................................................. 87

Table of contents
SIMATIC IPC427E
Operating Instructions, 09/2017, A5E37454814-AB 7
7.4.2 Partitioning the data storage medium .....................................................................................89
7.4.2.1 Partitioning in Windows Embedded Standard 7 .....................................................................89
7.4.2.2 Setting up the partitions under Windows 7 Ultimate and Windows 10 ...................................90
7.4.2.3 Adapting the partitions under Windows 7 Ultimate and Windows 10 .....................................91
7.4.3 Installing drivers and software ................................................................................................92
7.4.4 Update installation ..................................................................................................................93
7.4.4.1 Updating the operating system ...............................................................................................93
7.4.4.2 Installing or updating application programs and drivers .........................................................93
7.4.5 Backing up data ......................................................................................................................93
7.5 Recycling and disposal ...........................................................................................................93
8 Technical specifications ........................................................................................................................ 95
8.1 Certificates and approvals ......................................................................................................95
8.2 Declaration of conformity ........................................................................................................97
8.2.1 CE marking .............................................................................................................................97
8.2.2 Electromagnetic compatibility, Industrial and Residential Areas ............................................97
8.3 Directives and declarations.....................................................................................................98
8.3.1 ESD guideline .........................................................................................................................98
8.4 Dimension drawings..............................................................................................................101
8.4.1 Dimension drawing - mounting on a DIN rail ........................................................................101
8.4.2 Dimension drawing - wall-mounting......................................................................................102
8.4.3 Dimension drawing - vertical mounting.................................................................................103
8.4.4 Dimension drawing - device with expansion cards...............................................................104
8.5 Technical specifications ........................................................................................................105
8.5.1 General technical specifications ...........................................................................................105
8.5.2 Ambient conditions................................................................................................................108
8.5.3 Power demand of the components .......................................................................................110
8.5.4 Integrated DC power supply .................................................................................................110
8.5.5 Typical power consumption ..................................................................................................111
8.6 Hardware descriptions ..........................................................................................................112
8.6.1 External ports........................................................................................................................112
8.6.1.1 COM1 / COM2 ......................................................................................................................112
8.6.1.2 CFast.....................................................................................................................................113
8.6.1.3 DisplayPort............................................................................................................................114
8.6.1.4 Ethernet ................................................................................................................................115
8.6.1.5 USB 3.0 port .........................................................................................................................115
8.6.2 Internal ports .........................................................................................................................116
8.6.2.1 PCIe card ..............................................................................................................................116
8.6.3 System resources .................................................................................................................118
8.6.3.1 Currently allocated system resources...................................................................................118
8.6.3.2 Allocation of system resources .............................................................................................118
8.6.4 I/O Address Areas.................................................................................................................120
8.6.4.1 Overview of the internal module registers ............................................................................120
8.6.4.2 Watchdog enable register / 066h select register (read/write, address 062h) .......................120
8.6.4.3 Watchdog trigger register (read only, address 066h) ...........................................................122
8.6.4.4 Output register user LED L1/L2/L3 (read/write, address 404Eh) .........................................122
8.6.4.5 Battery status register (read-only, address 404Dh)..............................................................123
8.6.4.6 NVRAM address register ......................................................................................................123

Table of contents
SIMATIC IPC427E
8Operating Instructions, 09/2017, A5E37454814-AB
8.7 BIOS description .................................................................................................................. 124
8.7.1 Overview .............................................................................................................................. 124
8.7.2 Opening the BIOS selection menu....................................................................................... 125
8.7.3 Structure of the BIOS Setup menu ...................................................................................... 126
8.7.4 Exit menu ............................................................................................................................. 128
8.7.5 BIOS update......................................................................................................................... 129
8.7.6 Alarm, error and system messages ..................................................................................... 131
8.8 Active Management Technology (AMT) .............................................................................. 132
8.8.1 Introduction .......................................................................................................................... 132
8.8.2 Overview of AMT.................................................................................................................. 133
8.8.3 Enabling Intel® AMT / basic configuration........................................................................... 133
8.8.4 Resetting the Intel® AMT to the default settings and disabling AMT .................................. 135
8.8.5 Determining the network address ........................................................................................ 136
8.8.6 Forcing user consent ........................................................................................................... 136
8.9 Functional scope in Windows .............................................................................................. 137
8.9.1 Windows Embedded Standard 7 ......................................................................................... 137
A Technical support.................................................................................................................................139
A.1 Service and support ............................................................................................................. 139
A.2 Troubleshooting ................................................................................................................... 140
A.3 Notes on the use of third-party modules.............................................................................. 141
B Markings and symbols .........................................................................................................................143
B.1 Overview .............................................................................................................................. 143
B.2 Safety ................................................................................................................................... 143
B.3 Operator controls ................................................................................................................. 143
B.4 Certificates, approvals and markings................................................................................... 144
B.5 Interfaces ............................................................................................................................. 145
C List of abbreviations .............................................................................................................................147
Glossary ..............................................................................................................................................153
Index ...................................................................................................................................................161

SIMATIC IPC427E
Operating Instructions, 09/2017, A5E37454814-AB 9
Overview
1
1.1
Product description
The SIMATIC IPC427E provides high-level industrial functionality.
●Compact design
●Maintenance-free operation
●High degree of ruggedness

Overview
1.1 Product description
SIMATIC IPC427E
10 Operating Instructions, 09/2017, A5E37454814-AB
1.1.1
Applications
The device provides industrial PC systems for high-performance and space-saving
applications in particular in the field of machine, systems and switchgear cabinet
engineering:
●Measuring and controlling process and machine data, for example, automated washing
systems, assembling machines and packaging machines
●Operating and visualization tasks with separate monitors or displays, for example,
information terminals and large-scale displays in automotive production
●Data logging and processing, for example, system data logging and distributed process
control
1.1.2
Features
Basic data
Installation •Installation on a DIN rail
•Wall mounting
•Vertical mounting
Processor •Intel® Celeron® Processor G3902E (2M Cache, 1.6 GHz)
•Intel® Core™ i3-6102E Processor (3M Cache, 1.9 GHz)
•Intel® Core™ i5-6442EQ Processor (6M Cache, up to 2.7 GHz)
•Intel® Xeon® Processor E3-1505L v5 (8M Cache, up to 2.8 GHz)
Main memory Memory modules without ECC:
•4 GB DDR4-SDRAM SODIMM
•8 GB DDR4-SDRAM SODIMM
•16 GB DDR4-SDRAM SODIMM
Memory module with ECC (not combinable with i5 CPU):
•8 GB DDR4-SDRAM SODIMM
•16 GB DDR4-SDRAM SODIMM
Free slots for expansion
cards
Up to 2 × PCIe cards (optional), depending on enclosure version;
max. 175 mm long
Graphics •Intel® HD Graphics 510 / 530 / P530 (depending on CPU type)
•2 x DisplayPort, maximum resolution 4096 x 2304 pixels
•Graphics memory is claimed in main memory (dynamic UMA)
Power supply
24 V DC (-20%/+20%) max. 4 A
Conditions of use
Operation without fan

Overview
1.1 Product description
SIMATIC IPC427E
Operating Instructions, 09/2017, A5E37454814-AB 11
Basic data
Drives and storage media
CFast card Can be used optionally as boot drive or additional data memory.
•2 GB
•4 GB
•8 GB
•16 GB
•30 GB
Hard disk
2.5", ≥ 320 GB, SATA (optional)
SSD (Solid State Disk)
2.5", ≥ 80 GB SATA (optional)
USB stick
External, can be connected via USB interface
Ports
Serial
COM1 / COM2 (RS 232, RS 422, RS 485 configurable), optional
Graphics
2 x DisplayPort DPP (DVI via DP++ to DVI adapter possible)
USB 4 × USB 3.0, simultaneous operation of max. 2 x high current ports,
backward compatible with USB 2.0/1.1
Ethernet
2 × (3 x optional) RJ45 (10/100/1000 Mbps), teaming-capable
Keyboard, mouse
Connected via external USB port
Extended device functions
Temperature monitoring •When permitted temperature range is exceeded
•Warnings can be analyzed by application program (local, via LAN)
Watchdog •Monitoring function for program execution
•Restart can be parameterized in the event of a fault
•Warnings can be analyzed by application program (local, via LAN)
LED display 4 LEDs for displaying system statuses; 3 of these can be freely pro-
grammed by the user
Transient voltage interruption
Up to 15 ms buffer time at full load
Buffer memory
512 KB optional
TPM Integrated Trusted Platform Module, optional, according to TPM 2.0
standard

Overview
1.1 Product description
SIMATIC IPC427E
12 Operating Instructions, 09/2017, A5E37454814-AB
Software
Operating systems
Available •None
•Windows Embedded Standard 7, SP1
•Windows 7 Ultimate, SP1
•Windows 10 IoT Enterprise LTSB 2016, 64-bit
Project-specific •LINUX
•QNX
•VxWorks

Overview
1.2 Design of the device
SIMATIC IPC427E
Operating Instructions, 09/2017, A5E37454814-AB 13
1.2
Design of the device
1.2.1
Interfaces and operating elements
①
On/off switch The on/off switch does not isolate the device from the power supply. Position
"OFF", when the "_" symbol is pressed. Position "OFF" is the delivery state.
②
24V DC
Power supply connection
③
Protective conductor
Protective conductor terminal
④
Memory card slot
Slot for CFast card with cover
⑤
4 × USB
USB 3.0 high current, backward compatible with USB 2.0/1.1
⑥
2 x DisplayPort
DisplayPort connection for digital monitor
⑦
3 × Ethernet / 2 x Ethernet
RJ45 interface (10/100/1000 Mbps); 2 x RJ45 (optional)
⑧
COM1
Serial interface (optional)
⑨
COM2
Serial interface (optional)

Overview
1.2 Design of the device
SIMATIC IPC427E
14 Operating Instructions, 09/2017, A5E37454814-AB
1.2.2
Status displays
LED
State
Description
PC ON/WD Off -
Green
BIOS ready to boot; PC running
Flashing green/yellow
(1 Hz)
BIOS in POST, power switch on
Yellow
Idle state
Flashing red (1 Hz)
Watchdog status display: active
RUN/STOP / L1
Off
-
Green
Can be controlled by user program
Yellow Can be controlled by controller program (e.g.
WinAC)
ERROR / L2
Off
-
Red
-
Flashing red Can be controlled by user program or controller
program (e.g. WinAC)
MAINT / L3
Off
-
Yellow
-
Red Can be controlled by controller program (e.g.
WinAC)
For additional information on controlling the LEDs or the NVRAM with a Windows operating
system, please refer to Output register user LED L1/L2/L3 (read/write, address 404Eh)
(Page 122). Example programs for controlling the LEDs on Windows operating systems are
available on the Customer Support page of Siemens Industry Automation and Drive
Technologies. (http://www.siemens.com/automation/service&support)

Overview
1.3 Accessories
SIMATIC IPC427E
Operating Instructions, 09/2017, A5E37454814-AB 15
1.3
Accessories
Siemens offers accessories not included in the scope of delivery for the device. For more
information on available accessories, refer to the Internet at:
Industry Mall (https://mall.industry.siemens.com)
Expansion components and accessories (http://www.automation.siemens.com/mcms/pc-
based-automation/en/industrial-pc/expansion_components_accessories)
SIMATIC IPC CFast cards
●2 GB optional or
●4 GB optional or
●8 GB optional or
●16 GB optional or
●30 GB optional
Memory modules
●SO-DIMM module 4096 MB DDR4-SDRAM
●SO-DIMM module 8192 MB DDR4-SDRAM
●SO-DIMM module 16384 MB DDR4-SDRAM
●SO-DIMM module 8192 MB DDR4-SDRAM ECC
●SO-DIMM module 16384 MB DDR4-SDRAM ECC
Mounting sets
●Mounting onto standard rail
●Wall mounting
●Vertical mounting

Overview
1.3 Accessories
SIMATIC IPC427E
16 Operating Instructions, 09/2017, A5E37454814-AB

SIMATIC IPC427E
Operating Instructions, 09/2017, A5E37454814-AB 17
Safety Instructions
2
2.1
General safety instructions
WARNING
Life-threatening voltages are present with an open control cabinet
When you install the device in a control cabinet, some areas or components in the open
control cabinet may be carrying life-threatening voltages.
If you touch these areas or components, you may be killed by electric shock.
Switch off the power supply to the cabinet before opening it.
System expansions
NOTICE
Damage through system expansions
Device and system expansions may be faulty and can affect the entire machine or plant.
The installation of expansions can damage the device, machine or plant. Device and
system expansions may violate safety rules and regulations regarding radio interference
suppression. If you install or exchange system expansions and damage your device, the
warranty becomes void.

Safety Instructions
2.1 General safety instructions
SIMATIC IPC427E
18 Operating Instructions, 09/2017, A5E37454814-AB
Note the following for system expansions:
●Only install system expansion devices designed for this device. Contact your technical
support team or where you purchased your PC to find out which system expansion
devices may safely be installed.
●Observe the information on electromagnetic compatibility (Page 97).
NOTICE
"Open Type" UL508
Note that the device is classified as "Open Type" for use in the area of Industrial Control
Equipment (UL508). Installation of the device in an enclosure complying with UL508 for
specific permitted mounting positions (see corresponding section) is a prerequisite for
approval or operation in accordance with UL508.
WARNING
Risk of fire through expansion cards
Expansion cards generate additional heat. The device may overheat and cause a fire.
Please note the following:
•Observe the safety and installation instructions for the expansion cards.
•If in doubt, install the device in an enclosure that is compliant with sections 4.6 and 4.7.3
of the IEC/UL/EN/DIN-EN 60950-1 standard.
Battery and rechargeable battery
WARNING
Risk of explosion and release of harmful substances
Improper handling of lithium batteries can result in an explosion of the batteries.
Explosion of the batteries and the released pollutants can cause severe physical injury.
Worn batteries jeopardize the function of the device.
Note the following when handling lithium batteries:
•Replace used batteries in good time; see the section "Replacing the backup battery" in
the operating instructions.
•Replace the lithium battery only with an identical battery or types recommended by the
manufacturer (order no.: A5E34734290).
•Do not throw lithium batteries into fire, do not solder on the cell body, do not recharge,
do not open, do not short-circuit, do not reverse polarity, do not heat above 100°C and
protect from direct sunlight, moisture and condensation.

Safety Instructions
2.1 General safety instructions
SIMATIC IPC427E
Operating Instructions, 09/2017, A5E37454814-AB 19
High frequency radiation
NOTICE
Unintentional operating situations
High frequency radiation, e g. from a cellular phone, interferes with device functions and
can result in malfunctioning of the device.
Persons are injured and the plant is damaged.
Avoid high-frequency radiation:
•Remove radiation sources from the environment of the device.
•Switch off radiating devices.
•Reduce the radio output of radiating devices.
•Observe the information on electromagnetic compatibility (Page 97).
ESD Guideline
Electrostatic sensitive devices can be labeled with an appropriate symbol.
NOTICE
Electrostatic sensitive devices (ESD)
When you touch electrostatic sensitive components, you can destroy them through voltages
that are far below the human perception threshold.
If you work with components that can be destroyed by electrostatic discharge, observe the
ESD Guideline (Page 98).
Industrial Security
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions only form one element of such a concept.
Customer is responsible to prevent unauthorized access to its plants, systems, machines
and networks. Systems, machines and components should only be connected to the
enterprise network or the internet if and to the extent necessary and with appropriate security
measures (e.g. use of firewalls and network segmentation) in place.
Additionally, Siemens’ guidance on appropriate security measures should be taken into
account. For more information about industrial security, please visit
(http://www.siemens.com/industrialsecurity).

Safety Instructions
2.1 General safety instructions
SIMATIC IPC427E
20 Operating Instructions, 09/2017, A5E37454814-AB
Siemens’ products and solutions undergo continuous development to make them more
secure. Siemens strongly recommends to apply product updates as soon as available and to
always use the latest product versions. Use of product versions that are no longer supported,
and failure to apply latest updates may increase customer’s exposure to cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed under (https://support.industry.siemens.com).
Disclaimer for third-party software updates
This product includes third-party software. Siemens AG only provides a warranty for
updates/patches of the third-party software, if these have been distributed as part of a
Siemens software update service contract or officially released by Siemens AG. Otherwise,
updates/patches are undertaken at your own risk. You can find more information about our
Software Update Service offer on the Internet at Software Update Service
(http://www.automation.siemens.com/mcms/automation-software/en/software-update-
service).
Notes on protecting administrator accounts
A user with administrator privileges has extensive access and manipulation options in the
system.
Therefore, ensure there are adequate safeguards for protecting the administrator accounts
to prevent unauthorized changes. To do this, use secure passwords and a standard user
account for normal operation. Other measures, such as the use of security policies, should
be applied as needed.