Siemens SIMATIC IPC547C User manual

SIMATIC Industrial PC SIMATIC IPC547C
_
_____________
_
_____________
_
_____________
_
_____________
_
_____________
_
_____________
_
_____________
_
_____________
Introduction 1
Description
2
Application Planning
3
Installing
4
Connecting
5
Commissioning
6
Dimension drawings
7
Appendix
A
SIMATIC
Industrial PC
SIMATIC IPC547C
Getting Started
06/2009
A5E02411398-01

Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.
CAUTION
without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.
NOTICE
indicates that an unintended result or situation can occur if the corresponding information is not taken into
account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The device/system may only be set up and used in conjunction with this documentation. Commissioning and
operation of a device/system may only be performed by qualified personnel. Within the context of the safety notes
in this documentation qualified persons are defined as persons who are authorized to commission, ground and
label devices, systems and circuits in accordance with established safety practices and standards.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be adhered to. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this
publication may be trademarks whose use by third parties for their own purposes could violate the rights of the
owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E02411398-01
Ⓟ 06/2009
Copyright © Siemens AG 2009.
Technical data subject to change

SIMATIC IPC547C
Getting Started, 06/2009, A5E02411398-01 3
Table of contents
1 Introduction................................................................................................................................................ 5
2 Description................................................................................................................................................. 7
2.1 External structure...........................................................................................................................7
2.2 Operator Controls ..........................................................................................................................8
2.3 Connection components ................................................................................................................9
2.4 Status indicators ..........................................................................................................................11
3 Application Planning ................................................................................................................................ 13
3.1 Transport......................................................................................................................................13
3.2 Unpacking and checking the delivery unit ...................................................................................13
3.3 Ambient and environmental conditions........................................................................................15
3.4 Access protection.........................................................................................................................16
4 Installing .................................................................................................................................................. 17
4.1 Installing the device .....................................................................................................................17
4.2 Technical data of the telescopic rails...........................................................................................18
5 Connecting .............................................................................................................................................. 19
5.1 Connecting peripherals ................................................................................................................19
5.2 Connecting the device to power...................................................................................................20
6 Commissioning ........................................................................................................................................ 25
6.1 Requirements for commissioning.................................................................................................25
6.2 Initial Commissioning - Initial Startup...........................................................................................26
6.3 Reinstalling the software..............................................................................................................27
7 Dimension drawings ................................................................................................................................ 29
7.1 Dimensional drawing of the device ..............................................................................................29
7.2 Dimensional drawing for the use of telescopic rails.....................................................................30
A Appendix.................................................................................................................................................. 31
A.1 Guidelines and declarations.........................................................................................................31
A.2 Certificates and Approvals...........................................................................................................32
A.3 Service and support .....................................................................................................................34
Index........................................................................................................................................................ 35

Table of contents
SIMATIC IPC547C
4 Getting Started, 06/2009, A5E02411398-01

SIMATIC IPC547C
Getting Started, 06/2009, A5E02411398-01 5
Introduction 1
Purpose of the Getting Started
This Getting Started documentation contains all the information you need for commissioning
and using the SIMATIC IPC547C.
Validity of this Getting Started
This Getting Started is valid for all supplied variations of the SIMATIC IPC547C and
describes the delivery status as of May 2009.
Operating instructions SIMATIC IPC547C
The operating instructions are supplied with the device in electronic form as a PDF file on the
"IPC547C Documentation and Drivers" CD.
The operating instructions provide useful information on many topics, such as the hardware
expansion options, modification of the system configuration and technical data.
Conventions
The term "PC" or "device" is sometimes used to refer to the SIMATIC IPC547C product in
this documentation.
Note
Safety information
To avoid damage to assets and for the sake of your own personal safety, please take note of
the information on safety in this Getting Started and in the operating instructions. A warning
triangle references this safety information and is shown depending on the potential hazard.

Introduction
SIMATIC IPC547C
6 Getting Started, 06/2009, A5E02411398-01

SIMATIC IPC547C
Getting Started, 06/2009, A5E02411398-01 7
Description 2
2.1 External structure
Front view of the device Pos Description
① Front panel with aperture for ventilation of the
device (filter mat and fan are located behind this
front panel)
② Installation options for DVD ROM drives, DVD
burners and removable hard disk racks
③ Installation options for DVD ROM drives, DVD
burners
④ On/off button
⑤ Front door with lock,
provides protection against dirt and
unauthorized access. Keep the front door
closed during normal operation.
⑥ Diskette drive
⑦ USB ports
⑧ Rating plate
  
 
⑨ Status displays
Rear view of the device Pos Description
① Power unit fan
② Fan aperture
Installation option for 60 mm fan
③ Blanking panel
Option for installing a cover for external ports
④ Expansion slots
4 x PCI, 1x PCIe x16, 1x PCIe x8 (1 Lane),
1x PCIe x1
⑤ Connection elements
  

⑥ Power supply connection

Description
2.2 Operator Controls
SIMATIC IPC547C
8 Getting Started, 06/2009, A5E02411398-01
2.2 Operator Controls
Operator control on/off button Pos Description

① The on/off/reset buttons have three functions:
- Switch on the PC (press briefly 1x)
- Shut down the operating system and PC
(press briefly 1x)
- Switch off the PC without shutting down the operating system
(press and hold more than 4 seconds) = hardware reset.
CAUTION
Data may be lost when the PC performs a hardware reset.
WARNING
The on/off button signal does not cut off power to the PC!
Operator control elements of redundant power
supply
Pos Description
① Description: On / Off switch
(The on/off button signal does not cut off power to the PC!)


② Power LED
•Status display for redundant power supply
LED lit green: Power supply in operation
If there is no redundancy, you will be hear an acoustic
signal permanently.

Description
2.3 Connection components
SIMATIC IPC547C
Getting Started, 06/2009, A5E02411398-01 9
2.3 Connection components
Ports
Port location at the rear of the device
  


     





Pos Description Description
① MOUSE Connection for a PS/2 mouse
② COM 1 Serial port 1 (V.24), 9-pin D-sub connector
③ LPT Parallel port, 25-pin
④ COM 2 Serial port 2 (V.24), 9-pin D-sub connector (optional)
⑤ Ethernet 1, 2 2 x RJ-45 Ethernet connectors for 10/100/1000 Mbps 1)
⑥ DVI or DMS59
connection
DVI-D connection of ADD2 card for digital monitors (optional) or
DMS59 connector of dual-head graphics card (optional)
⑦ Line in Connector for analog audio source, 3.5 mm phono jack
⑧ Line out Connector for active speakers or headset, 3.5 mm phono jack
⑨ Micro (input) Connection for microphone, 3.5 mm phono jack
⑩ USB 6 ports for USB devices
⑪ VGA Connection for VGA monitor
⑫ KEYBOARD Connection for a PS/2 keyboard
⑭ VGA 2) VGA connection (adapter plugged in)
⑮ DVI-I 2) DVI-I connection
⑯ Dual-head adapter 2) DMS59 connector on dual-head graphics card (optional)
1) For unique labeling, the LAN interfaces are numbered on the housing.
The numbering by the operating system may deviate from this.
2) Using the graphic card

Description
2.3 Connection components
SIMATIC IPC547C
10 Getting Started, 06/2009, A5E02411398-01
Power supply
Table 2- 1
Position of the IEC power connector Description
IEC connector for the AC power supply to the device. The permitted
power range is 100 VAC to 240 VAC.
Redundant power supply
Redundant power supply Pos Description
① IEC connector for the AC power supply to the device. The
permitted power range is 100 VAC to 240 VAC.
② On / Off switch
③ LED of power supply
④ Alarm reset





Description
2.4 Status indicators
SIMATIC IPC547C
Getting Started, 06/2009, A5E02411398-01 11
2.4 Status indicators
Status displays
 
Pos Display Meaning LEDs Description
① TEMP Temperature status OFF
RED
•No error
•Temperature critical (CPU, device
temperature).
② FAN Fan status •CPU heat sink fan fault
•Enclosure fan fault
•Power supply fan fault
③ HDD Display for hard disk
access
OFF
GREEN
•No access
•Access
④ POWER PC operating status
display
OFF
GREEN
flashing
GREEN
•Hibernate, switched off or unplugged
•Windows standby
•PC in operation

Description
2.4 Status indicators
SIMATIC IPC547C
12 Getting Started, 06/2009, A5E02411398-01
Rear status displays

/(' /('
Display Meaning LED Description
OFF •No cable connected
•Cable disabled
•Interface disabled
Green LED
Link status display
GREEN Active cable connected
OFF •No cable connected
•Cable disabled
•Interface disabled
•No activity
Ethernet LAN 1, 2 *
Yellow LED
Activity status display
YELLOW Data transfer active
* For unique labeling, the LAN interfaces are numbered on the housing. The numbering by the
operating system may deviate from this.

SIMATIC Industrial PC SIMATIC IPC547C
Getting Started, 06/2009, A5E02411398-01 13
Application Planning 3
3.1 Transport
Despite the device's rugged design, its internal components are sensitive to severe
vibrations or shock. You must therefore protect the PC from severe mechanical stress when
transporting it.
You should always use the original packaging for shipping and transporting the device.
CAUTION
Risk of damage to the device!
When transporting the PC in cold weather, it may be submitted to extreme variations in
temperature. In this situation, ensure that no moisture (condensation) develops on or inside
the device.
If condensation develops, wait at least 12 hours before switching on the device.
3.2 Unpacking and checking the delivery unit
Unpacking the device
Note the following points when you unpack the unit
● It is advisable not to dispose of the original packing material. Keep it in case you have to
transport the unit again.
● Please keep the documentation in a safe place. It is required for initial commissioning and
is part of the device.
● Check the delivery unit for any signs of visible transport damage.
● Verify that the shipment contains the complete unit and your separately ordered
accessories.
● Please inform your local dealer of any disagreements or transport damages.
● Please inform Siemens AG by means of the enclosed SIMATIC IPC/PG quality control
report form.

Application Planning
3.2 Unpacking and checking the delivery unit
SIMATIC IPC547C
14 Getting Started, 06/2009, A5E02411398-01
Noting the device identification data
The device can be identified uniquely with the help of these numbers in case of repairs or
theft.
Enter the following data in the table below:
● Serial number: The serial number (S VP) is located on the rating plate inside the front
door.
Figure 3-1 Rating plate
● Order number of the device
● Ethernet address: The Ethernet address of the device is available in BIOS Setup (F2
function key) , at Info > (F1 function key) > LAN Address.
● Microsoft Windows "Product Key" on the "Certificate of Authenticity" (COA). The COA
label is attached to the inside of the front door.
You may need the Product Key in case you reinstall the operating system.
Figure 3-2 COA label
Serial number S VP ...
Order no. 6AG4104-1 ...
Microsoft Windows Product Key
Ethernet address 1
Ethernet address 2
Device equipment
You will find a list of device equipment on a label behind the front door.

Application Planning
3.3 Ambient and environmental conditions
SIMATIC IPC547C
Getting Started, 06/2009, A5E02411398-01 15
3.3 Ambient and environmental conditions
When you plan your project, you should make allowances for:
● The climatic and mechanical environmental conditions specified in the specifications
provided by your operating instructions.
● Avoid extreme ambient conditions as far as possible. Protect your PC from dust,
moisture, and heat.
● The device has been designed for usage in a normal industrial environment according to
IEC 60721-3-3 (pollutant class 3C2 for chemical influence, 3S2 for sand and dust). PC
may not be used in severe operating environments, for example locations with acidic
vapors or gasses, without additional protective measures (such as the provision of clean
air).
● Keep the PC out of direct sunlight.
● Mount the PC as safely as possible to prevent danger (for example, of falling over).
● The device conforms to protection class IP 30 at the front panel.
● The clearance in the area of the ventilation slots must be at least 50 mm, so that the PC
is sufficiently ventilated.
● Do not cover the vent slots of the device.
● The device fulfills the requirements for a fire enclosure according to EN 60950-1. It can
be installed without additional fire protection.
● The connected or added peripherals must not introduce a counter emf greater than 0.5 V
into the device.
WARNING
Failure to comply with these requirements for system installation shall render approvals
to UL 60950-1, EN 60950-1 void and leads to the risk of overheating and injury!

Application Planning
3.4 Access protection
SIMATIC IPC547C
16 Getting Started, 06/2009, A5E02411398-01
3.4 Access protection
The access protection of the device exists only when the front panel is closed and no
keyboards with an On/Off button (power button) are being used.
Note
In Windows, you have the option of setting the function of the On/Off button to meet your
requirements. You can make these setting in the "Power Options" menu.

SIMATIC IPC547C
Getting Started, 06/2009, A5E02411398-01 17
Installing 4
4.1 Installing the device
Optional mounting locations
The device can be mounted in control desks, switching cabinets and 19" rack systems, both
horizontally and vertically.
Optional mounting methods
The device can be mounted with the following methods
● Mounting with cabinet brackets
● Mounting on device bases
● Tower installation: a separate tower kit can be ordered for tower installation (not available
in some countries).
● Mounting on telescopic rails
These telescopic rails allow you to fully extract the device out of the cabinet or rack.
Refer to the sections Technical data of the telescopic rails (Page 18) and Dimensional
drawing for the use of telescopic rails (Page 30) for more detailed information.

Position of the mounting holes ① for angle brackets or telescopic rails

Installing
4.2 Technical data of the telescopic rails
SIMATIC IPC547C
18 Getting Started, 06/2009, A5E02411398-01
CAUTION
The mounting screws of the telescopic rails may not protrude more than 5 mm into the
enclosure.
Note
For vertical operation, mount the device on a horizontal metal base and secure it against
tipping. The following decide bases are available from Rittal for this purpose:
Rittal Type TE 7000.620, Rittal Type VR 3861.580, Rittal Type DK 7063.710.
Please refer to the case manufacturer's instructions regarding device bases.
CAUTION
Risk of injury!
It is not permitted to mount the device only on the 19" brackets of the front panel.
4.2 Technical data of the telescopic rails
Ultimate load per pair At least 30 kg
Full extraction length At least 470 mm
Rail thickness Maximum 9.7 mm
Mounting screws M5 x 6 mm
The mounting screws of the telescopic rails may not protrude by more than 5 mm into the
enclosure.

SIMATIC IPC547C
Getting Started, 06/2009, A5E02411398-01 19
Connecting 5
5.1 Connecting peripherals
Note before connecting
NOTICE
Connect only peripherals approved for industrial applications according to EN / IEC 61000-
6-2.
Note
Hot-plug peripherals (USB) may be connected while the PC is in operation.
CAUTION
Peripherals that are incapable of hot-plugging may only be connected after the device has
been disconnected from the power supply.
CAUTION
Strictly adhere to the specifications for peripheral equipment.
NOTICE
The connected or added peripherals must not introduce any counter emf into the device.
A counter e.m.f. greater than 0.5 V to ground on the + 3.3 V DC / + 5 V DC / + 12 V DC
voltage due to a connected or integrated component can prevent normal operation or even
destroy the computer.
When measuring the counter emf, remember the following:
•The computer in question must be turned off and the power supply connector should be
plugged in.
•During the measurement, all cables from the plant to the computer should be
connected.
•All other components in the plant must be active.

Connecting
5.2 Connecting the device to power
SIMATIC IPC547C
20 Getting Started, 06/2009, A5E02411398-01
5.2 Connecting the device to power
Note before you connect the device
Note
The long-range power supply module is designed for operation on 100-240 AC networks. It
is not necessary to adjust the voltage range.
WARNING
Do not connect or disconnect power and data cables during thunderstorms.
WARNING
The device may only be operated on grounded power supply networks (TN systems to VDE
0100, part 300, or IEC 60364-3).
Operation on ungrounded or impedance-grounded power networks (IT networks) is
prohibited.
WARNING
The permitted nominal voltage of the device must conform with local mains voltage.
CAUTION
The mains connector must be disconnected to fully isolate the device from mains. Ensure
easy access to this area.
A master mains disconnect switch must be installed if the device is mounted in a switch
cabinet. Always ensure free and easy access to the power inlet on the device or that the
safety power outlet of the building installation is freely accessible and located close to the
device.
Note
The power supply contains a PFC (Power Factor Correction) circuit to conform to the EMC
directive.
Uninterruptible AC power systems (UPS) must supply a sinusoidal output voltage in the
normal and buffered mode when used with SIMATIC PCs with a PFC.
UPS characteristics are described and classified in the standards EN 50091-3 or
IEC 62040-3. Devices with sinusoidal output voltage in the normal and buffered mode are
identified with the classification "VFI-SS-...." or "VI-SS-....".