Siemens SENTRON PAC2200CLP User manual

PAC2200CLP
SENTRON
7KM power monitoring device
PAC2200CLP
Equipment Manual
06/2021
L1V30820585B
-02
Introduction
1
Description
2
Installation
3
Connection
4
Operation
5
Commissioning
6
Service and maintenance
7
Technical specifications
8
Dimension drawings
9
Appendix
A

Siemens AG
Digital Industries
Postfach 48 48
90026 NÜRNBERG
GERMAN
Y
Ⓟ
06/2021 Subject to change
Copyright © Siemens AG 2020.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

PAC2200CLP
Equipment Manual, 06/2021, L1V30820585B-02 3
Table of contents
1 Introduction........................................................................................................................................... 7
1.1 Components of the product ................................................................................................. 7
1.2 Latest information ............................................................................................................... 7
1.3 Security information ............................................................................................................ 9
1.4 Open Source Software ......................................................................................................... 9
1.5 Advanced training courses ................................................................................................. 10
1.6 Risk of manipulation .......................................................................................................... 11
2 Description........................................................................................................................................... 13
2.1 Performance features......................................................................................................... 13
2.2 Measuring inputs............................................................................................................... 17
2.3 Functions for delimiting third-party quantities according to §62b Par. 1 of the
Renewable Energy Act ....................................................................................................... 19
2.3.1 Configuring the device time............................................................................................... 19
2.3.1.1 Navigating to main menu, settings, date/time .................................................................... 20
2.3.1.2 Parameterization ............................................................................................................... 20
2.3.1.3 Synchronization errors....................................................................................................... 22
2.3.1.4 Possible time synchronization scenarios ............................................................................. 22
2.3.2 Logbook ............................................................................................................................ 24
2.3.2.1 Navigating to main menu, logbook .................................................................................... 24
2.3.2.2 Examples of logbook entries .............................................................................................. 25
2.3.3 Load profile ....................................................................................................................... 26
2.3.3.1 Navigating to main menu, load profile ............................................................................... 26
2.3.3.2 Load profile overview ........................................................................................................ 27
2.3.3.3 Detailed view of load profile............................................................................................... 27
2.3.3.4 Display with invalid values ................................................................................................. 29
2.4 Averaging measured values ............................................................................................... 30
2.4.1 Averaging measured values ............................................................................................... 30
2.4.2 Load profile – energy consumption profile ......................................................................... 30
2.4.3 Energy counters................................................................................................................. 31
2.5 Digital inputs and outputs.................................................................................................. 33
2.5.1 Digital inputs and outputs.................................................................................................. 33
2.5.2 Digital input....................................................................................................................... 33
2.5.3 Digital output .................................................................................................................... 34
2.6 Communication................................................................................................................. 36
2.6.1 Ethernet ............................................................................................................................ 36
3 Installation........................................................................................................................................... 37
3.1 Introduction ...................................................................................................................... 37
3.2 Installation steps................................................................................................................ 38

Table of contents
PAC2200CLP
4Equipment Manual, 06/2021, L1V30820585B-02
3.3 Removal ............................................................................................................................ 38
4 Connection .......................................................................................................................................... 39
4.1 Safety notes ...................................................................................................................... 39
4.2 Connections ...................................................................................................................... 41
4.3 Connection examples ........................................................................................................ 43
4.4 Connecting the communication cable ................................................................................ 46
4.4.1 Ethernet communication cable .......................................................................................... 46
4.4.2 Grounding of the Ethernet cable ........................................................................................ 46
5 Operation............................................................................................................................................. 49
5.1 Device interface................................................................................................................. 49
5.1.1 Displays and operator controls ........................................................................................... 49
5.1.2 SW button ......................................................................................................................... 50
5.1.3 Control keys ...................................................................................................................... 50
5.2 Menu navigation ............................................................................................................... 51
5.2.1 Measured value level ......................................................................................................... 51
5.2.2 Main menu level................................................................................................................ 51
5.2.3 Setting level ...................................................................................................................... 52
5.2.4 Editing level....................................................................................................................... 52
5.3 Supporting software .......................................................................................................... 53
5.3.1 powermanager.................................................................................................................. 53
5.3.2 powerconfig ...................................................................................................................... 53
5.3.3 Web server ........................................................................................................................ 54
5.3.4 Advanced training courses ................................................................................................. 55
5.4 Protection against manipulation......................................................................................... 55
5.4.1 Introduction ...................................................................................................................... 55
5.4.2 Password protection .......................................................................................................... 56
5.4.3 Hardware write protection................................................................................................. 57
5.4.4 IP filter (subnet firewall protection).................................................................................... 57
5.4.5 Modbus TCP port, configurable .......................................................................................... 57
6 Commissioning .................................................................................................................................... 59
6.1 Overview........................................................................................................................... 59
6.2 Applying the measuring voltage......................................................................................... 59
6.3 Parameterizing the device.................................................................................................. 60
6.3.1 Parameterizing with powerconfig....................................................................................... 60
6.3.2 Parameterization via the device menu................................................................................ 63
7 Service and maintenance .................................................................................................................... 73
7.1 Cleaning............................................................................................................................ 73
7.2 Calibration......................................................................................................................... 73
7.3 Troubleshooting guide....................................................................................................... 73
7.4 Warranty ........................................................................................................................... 75
8 Technical specifications....................................................................................................................... 77
8.1 Technical specifications ..................................................................................................... 77

Table of contents
PAC2200CLP
Equipment Manual, 06/2021, L1V30820585B-02 5
8.2 Labeling ............................................................................................................................ 89
9 Dimension drawings............................................................................................................................ 91
9.1 Dimensional drawings ....................................................................................................... 91
A Appendix ............................................................................................................................................. 93
A.1 Modbus TCP....................................................................................................................... 93
A.1.1 Function codes .................................................................................................................. 93
A.1.2 Modbus exception codes.................................................................................................... 94
A.1.3 Modbus measured variables with the function codes 0x03 and 0x04.................................. 95
A.1.4 Modbus measured variables with function codes 0x14, 0x03 and 0x04 .............................. 99
A.1.5 Structure - Digital input status and digital output status with the function codes 0x03
and 0x04......................................................................................................................... 105
A.1.6 Structure - Device diagnostics and device status with the function codes 0x03 and
0x04................................................................................................................................ 105
A.1.7 Modbus status parameters with the function code 0x02................................................... 106
A.1.8 Modbus settings with the function codes 0x03, 0x04 and 0x10........................................ 107
A.1.9 Modbus communication parameters with the function codes 0x03, 0x04 and 0x10.......... 108
A.1.10 Modbus device information with the function codes 0x03, 0x04 and 0x10 ....................... 110
A.1.11 Modbus command parameters......................................................................................... 111
A.1.12 Modbus standard device identification with the function code 0x2B ................................. 112
A.1.13 Active energy history with the Modbus function codes 0x14, 0x03 and 0x04.................... 112
A.1.14 User-defined Modbus function code 0x64 ........................................................................ 119
Index.................................................................................................................................................. 125

Table of contents
PAC2200CLP
6Equipment Manual, 06/2021, L1V30820585B-02

PAC2200CLP
Equipment Manual, 06/2021, L1V30820585B-02 7
Introduction
1
1.1 Components of the product
The package includes:
•PAC2200CLP power monitoring device
•PAC2200CLP operating instructions
Available accessories
•powerconfig software (https://support.industry.siemens.com/cs/ww/en/view/63452759)
•powermanager software
(https://support.industry.siemens.com/cs/ww/en/view/109771760)
1.2 Latest information
Up-to-the-minute information
You can find further assistance:
on the Internet:
Website (https://support.industry.siemens.com/my/ww/en/requests)

Introduction
1.2 Latest information
PAC2200CLP
8Equipment Manual, 06/2021, L1V30820585B-02
General safety notes
DANGER
Hazardous voltage.
Will cause death, serious personal injury, or equipment damage.
Turn off and lock out all power supplying this equipment before working on this device.
WARNING
Impairment of protection will result from improper use.
Can cause death, serious personal injury, or equipment damage.
The device may be used only for the applications described in the catalog and the associated
technical documentation.
Note
These operating instructions do not purport to cover all details or variations in equipment, or
to provide for every
possible contingency in connection with installation, operation, or
maintenance. Should additional information be desired, or should particular problems arise
that are not discussed in enough detail in the operating instructions, please contact Technical
S
upport (https://www.siemens.com/lowvoltage/technical-support) for the information you
require.
Safety-related symbols on the device
Symbol
Meaning
(1)
Danger of electric shock
(2)
General Warning Symbol
(3)
Electrical installation and maintenance by qualified personnel only

Introduction
1.3 Security information
PAC2200CLP
Equipment Manual, 06/2021, L1V30820585B-02 9
1.3 Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be connected
to an enterprise network or the Internet if and to the extent such a connection is necessary
and only when appropriate security measures (e.g. firewalls and/or network segmentation)
are in place.
For additional information on industrial security measures that may be implemented, please
visit (https://www.siemens.com/industrialsecurity).
Siemens’ products and solutions undergo continuous development to make them more
secure. Siemens strongly recommends that product updates are applied as soon as they are
available and that the latest product versions are used. Use of product versions that are no
longer supported, and failure to apply the latest updates may increase customer's exposure to
cyber threats.
To keep up to date with all the latest product updates, subscribe to the Siemens Industrial
Security RSS Feed at (https://www.siemens.com/industrialsecurity).
1.4 Open Source Software
This product, solution or service ("Product") contains third-party software components. These
components are Open Source Software licensed under a license approved by the Open
Source Initiative or similar licenses as determined by SIEMENS ("OSS") and/or commercial or
freeware software components. With respect to the OSS components, the applicable OSS
license conditions prevail over any other terms and conditions covering the Product. The OSS
portions of this Product are provided royalty-free and can be used at no charge.
If SIEMENS has combined or linked certain components of the Product with/to OSS
components licensed under the GNU LGPL version 2 or later as per the definition of the
applicable license, and if use of the corresponding object file is not unrestricted ("LGPL
Licensed Module", whereas the LGPL Licensed Module and the components that the LGPL
Licensed Module is combined with or linked to is the "Combined Product"), the following
additional rights apply, if the relevant LGPL license criteria are met: (i) you are entitled to
modify the Combined Product for your own use, including but not limited to the right to
modify the Combined Product to relink modified versions of the LGPL Licensed Module, and
(ii) you may reverse-engineer the Combined Product, but only to debug your modifications.
The modification right does not include the right to distribute such modifications and you
shall maintain in confidence any information resulting from such reverse-engineering of a
Combined Product.
Certain OSS licenses require SIEMENS to make source code available, for example, the GNU
General Public License, the GNU Lesser General Public License and the Mozilla Public License.
If such licenses are applicable and this Product is not shipped with the required source code, a
copy of this source code can be obtained by anyone in receipt of this information during the
period required by the applicable OSS licenses by contacting the following address:

Introduction
1.5 Advanced training courses
PAC2200CLP
10 Equipment Manual, 06/2021, L1V30820585B-02
Siemens AG
Smart Infrastructure
Electrical Products
Technical Support
Postfach 10 09 53
93009 Regensburg
Germany
You will find Technical Support under.
Keyword: Open Source Request (please specify Product name and version, if applicable)
SIEMENS may charge a handling fee of up to 5 EUR to fulfil the request.
Warranty regarding further use of the Open Source Software
SIEMENS' warranty obligations are set forth in your agreement with SIEMENS. SIEMENS does
not provide any warranty or technical support for this Product or any OSS components
contained in it if they are modified or used in any manner not specified by SIEMENS. The
license conditions may contain disclaimers that apply between you and the respective
licensor. For the avoidance of doubt, SIEMENS does not make any warranty commitment on
behalf of or binding upon any third-party licensor. The Open Source Software used in the
product and the license agreements concerning this software can be found in the
Readme_OSS.
See also
Industry Online Support (https://support.industry.siemens.com/cs/us/en/ps)
www.opensource.org (http://www.opensource.org)
1.5 Advanced training courses
Find out about training courses on offer on the following link.
Training for Industry (https://www.siemens.com/sitrain-lowvoltage)
Here you can choose from:
•Web-based training courses (online, informative, free)
•Classroom training courses (course attendance, comprehensive, subject to fee)
You also have the possibility of compiling your own training portfolio via Learning paths.

Introduction
1.6 Risk of manipulation
PAC2200CLP
Equipment Manual, 06/2021, L1V30820585B-02 11
1.6 Risk of manipulation
Note
Risk of manipulation
Several protective mechanisms can be activated in the device.
In order to reduce the risk of manipulation occurring on the device, it is
recommended that
the protective mechanisms available in the device are activated:
•
Password protection to protect the device against unintentional adjustment of
parameters.
•
Hardware write protection, to effectively prevent changes to the device parameters
without physical access to the device.
If you want to use the device for billing purposes, please refer to the notes at the end of
the chapter Parameterizing via the device menu (Page 63).

Introduction
1.6 Risk of manipulation
PAC2200CLP
12 Equipment Manual, 06/2021, L1V30820585B-02

PAC2200CLP
Equipment Manual, 06/2021, L1V30820585B-02 13
Description
2
2.1 Performance features
The PAC2200CLP is a power monitoring device for measuring the basic electrical variables in
low-voltage power distribution. All the measured variables are shown on the PAC2200CLP
display. The device is capable of single-phase, two-phase or three-phase measurement and
can be used in TN, TT and IT systems.
Please note that the MID approval and the national approval according to PTB A50.7 are valid
for use in single-phase and three-phase systems. Single-phase operation is only permitted on
L1.
The PAC2200CLP is installed on a standard mounting rail.
Several versions of the PAC2200CLP power monitoring device are available:
•5 A device:
X / 1 A and x / 5 A current transformers can be used for current measuring.
•65 A device:
No current transformers are required for current measuring. The device is connected
directly to the low-voltage network. Current of up to 65 A can be measured directly.
The PAC2200CLP power monitoring device features an integrated Ethernet interface.
Thanks to the wide measuring voltage range of the PAC2200CLP, it can be connected directly
in the low-voltage network up to a nominal line voltage UL-L of 400 V.
Measurement
•Measurement of all relevant electrical variables in an AC system
•Averaging of all measured values directly on the device in two stages, which are
independent of each other and freely configurable (aggregation)
•4-quadrant measurement for import and export
Counters and average power demand values
•Recording of active, reactive and apparent energy by means of several energy counters
•Calculation and storage of the last demand period average value for active and reactive
power for simple software-driven generation of load profiles
•Calculation of average values for active and reactive power of the last completed demand
period for import and export
•Time stamp of the current demand period acc. to ISO8601 (local and UTC time)
•MID-certified active energy counter for import and export (Measuring Instruments
Directive 2014/32/EU)

Description
2.1 Performance features
PAC2200CLP
14 Equipment Manual, 06/2021, L1V30820585B-02
•With load profile measurement conforming to statutory calibration regulations and
national approval according to PTB-A 50.7
•Integrated 15-minute load profile memory with a storage depth for all billing-relevant data
over 2 years
•Daily, monthly and annual consumption of active energy for import and export over 10
years
•Logbook for storing up to 8000 events relevant to statutory calibration regulations
according to PTB-A50.7
•Convenient display of load profile and logbook data on the device or via web server in the
form of a bar chart
•Download of load profile and logbook data via Modbus TCP or in the form of a csv file via
the integrated web server
•Internal device clock with high accuracy and time synchronization function via time server
Display and operator control
•LC display
•Four control keys with variable function assignment
•LEDs for Ethernet communication, active energy pulse indicator
•powerconfig
•powermanager
•Web server (HTTP)
Interfaces
•Ethernet
•Digital input
•Digital output
Memory
•Adjusted device parameters are permanently stored in the device memory.
•2-year storage period for all billing-relevant load profile data
•Logbook for 8000 events relevant to statutory calibration regulations
Time synchronization
When the SNTP server is set and activated, time synchronization takes place automatically
immediately after a device reboot.

Description
2.1 Performance features
PAC2200CLP
Equipment Manual, 06/2021, L1V30820585B-02 15
Security
•Hardware write protection
If you want to use the device for billing purposes, please refer to the notes at the end of
this chapter.
•Password protection
•Access protection IP filter
•Modbus TCP port, configurable
•HTTP port, configurable
•Dynamic host configuration protocol (DHCP) included
•Simple Network Time protocol (SNTP) included
•Possible to attach lead seals
Using "Password protection" and "Hardware write protection", you can protect against write
access to the device settings of the PAC2200CLP.
The protection intervenes in case of the following actions:
•Modify parameters in device
•Reset device to factory settings
•Reset password
The data can be read without any restrictions.
Note
Activate hardware write protection
When connecting the power monitoring device to a network, it is recommended that the
hardware write protection is activated.
Tariffs
PAC2200CLP supports 2 tariffs for the integrated energy counters (on-peak and off-peak).
These tariffs are for information only and are not intended for billing purposes.
Control of tariff switching
Tariff switching can be controlled via the digital input or the
communications interfaces.
Time-related switching is only possible using a higher-level system.
The tariff change becomes effective after expiry of the period.

Description
2.1 Performance features
PAC2200CLP
16 Equipment Manual, 06/2021, L1V30820585B-02
MID-approved
The devices have MID approval and national approval according to PTB-A50.7 for Germany.
They are therefore suitable for the measurement and delimitation of power consumption
quantities in conformance with statutory metering and calibration regulations according to
Renewable Energy Act §62b.
The following actions cannot be performed on the PAC2200CLP:
•Deletion of the energy counter
•Deletion or reset of load profile data
•Deletion of existing logbook entries
See also
Commissioning (Page 59)

Description
2.2 Measuring inputs
PAC2200CLP
Equipment Manual, 06/2021, L1V30820585B-02 17
2.2 Measuring inputs
Current measurement
NOTICE
AC current measurement only
The device is not suitable for measuring DC current.
The 5 A device is designed for:
•Measuring current of 5 A for connecting standard current transformers.
Each current measuring input can take a continuous load of 10 A. A short-time
overcurrent up to 100 A with a duration of 1 s is possible.
The 65 A device is designed for:
•Direct connection to the low-voltage network.
Voltage measurement
NOTICE
AC voltage measurement only
The device is not suitable for measuring DC voltage.
PAC2200CLP is designed for:
•Direct measurement on the network.
•Networks with line voltages up to 230 V / 400 V. The device is designed for connection
to low-voltage networks with nominal line voltages of 400 V / 230 V (UL-L/UL-N). In other
words, it can be used for measuring voltages up to 277 V line conductor to neutral
conductor and 480 V line conductor to line conductor.
Connection types
The device can be used in 2-wire and 4-wire systems (TN, TT and IT systems).
The device does not offer any setting option in the menu. The following connection types are
supported by the PAC2200CLP power monitoring device:
Table 2- 1 Connection types provided (connection to L1)
Short code
Connection type
1P2W
1 phase, 2 conductors
3P4W
3 phases, 4 conductors

Description
2.2 Measuring inputs
PAC2200CLP
18 Equipment Manual, 06/2021, L1V30820585B-02
Note
Use of connection type 1P2W
In
order to obtain accurate measured values, phase L1 must be used for single-phase
operation (1P2W).
NOTICE
Connection to the wrong supply voltage can cause irreparable damage to the device.
Before connecting PAC2200CLP, it must be ensured that the local power supply conditions
match the specifications on the nameplate.
Display of measured variables on the device display and via the web server
The table below shows which measured variables are displayed on the device and via the web
server.
A list of the measured values and other parameters which can be read out via the Modbus
TCP interface can be found in the appendix in chapter Modbus TCP (Page 93).
Table 2- 2 Display of measured variables on the device display and via the web server
Measured variable
Display
Web
Voltage L1-N,L2-N,L3-N
✓
✓
Voltage L12,L23,L31
✓
✓
Current L1,L2,L3
✓
✓
Neutral current (calculated)
✓
✓
Apparent power L1,L2,L3, ∑
✓
✓
Active power L1,L2,L3, ∑
✓
✓
Reactive power L1,L2,L3, ∑
✓
✓
Power factor L1,L2,L3, ∑
✓
✓
Line frequency
✓
✓
Active energy tariff T1 import, L1,L2,L3, ∑
✓
✓
Active energy tariff T2 import, L1,L2,L3, ∑
✓
✓
Active energy tariff T1 export, L1,L2,L3, ∑
✓
✓
Active energy tariff T2 export, L1,L2,L3, ∑
✓
✓
Active energy import (MID register) ∑
✓
✓
Active energy export (MID register) ∑
✓
✓
Secondary active energy import (MID register) ∑
✓
✓
Secondary active energy export (MID register) ∑
✓
✓
Reactive energy tariff T1 import, L1,L2,L3, ∑
✓
✓
Reactive energy tariff T2 import, L1,L2,L3, ∑
✓
✓
Reactive energy tariff T1 export, L1,L2,L3, ∑
✓
✓
Reactive energy tariff T2 export, L1,L2,L3, ∑
✓
✓
Apparent energy tariff T1 L1,L2,L3, ∑
✓
✓