Siemens XJ-L Busway System Instruction Manual

XJ-L Busway Systems
Storage, Installation and
Maintenance Instructions for...
Piece No. 32-J-1010-01 Rev 5
SIEMENS
XJ-L Busway System

1.0 Definitions
1.1 QUALIFIED PERSONNEL
FOR THE PURPOSE OF THIS MANUAL AND
PRODUCT LABELS, QUALIFIED PERSONNEL
IS ONE WHO IS FAMILIAR WITH THE
INSTALLATION, CONSTRUCTION AND
OPERATION OF THE EQUIPMENT AND THE
HAZARDS INVOLVED. IN ADDITION, HE OR
SHE HAS THE FOLLOWING QUALIFICA-
TIONS:
(a) Is trained and authorized to energize, de-energize,
clear, ground and tag circuits and equipment in
accordance with established safety practices.
(b) Is trained in the proper care and use of protective
equipment such as rubber gloves, hard hat, safety
glasses or face shields, flash clothing, etc., in
accordance with established safety practices.
(c) Is trained in rendering first aid.
1.2 DANGER
FOR THE PURPOSE OF THIS MANUAL AND PRODUCT
LABELS, DANGER INDICATES AN IMMINENTLY HAZ-
ARDOUS SITUATION WHICH, IF NOT AVOIDED, WILL
RESULT IN DEATH OR SERIOUS INJURY.
1.3 WARNING
FOR THE PURPOSE OF THIS MANUAL AND PRODUCT
LABELS, WARNING INDICATES A POTENTIALLY
HAZARDOUS SITUATION WHICH, IF NOT AVOIDED,
COULD RESULT IN DEATH OR SERIOUS INJURY.
1.4 CAUTION
FOR THE PURPOSE OF THIS MANUAL AND PRODUCT
LABELS, CAUTION INDICATES A POTENTIALLY
HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, MAY
RESULT IN MINOR OR MODERATE INJURY.
2.0 Storage Instructions
Upon receipt, immediately inspect busway components
for possible concealed damage from shipping and/or
handling. If damage has occurred, file a claim with the
carrier. If there is no damage, restore the packing to its
original condition to prepare for job site storage.
Store busway indoors in a clean and dry area. Protect
against mechanical damage and exposure to lime dust
(concrete), water, corrosive fumes or liquids and salts.
Failure to properly store and protect the busway can
cause damage and will void the warranty.
3.0 Preparing for Installation
Deliver busway to installation location before unpacking.
Shipping crates/cartons contain exterior identification of
the packaged busway components. Each busway com-
ponent is further identified by an item number located
on the nameplate, which corresponds to that same item
number on the busway installation drawing(s).
Inspect each busway component for possible damage.
Consult the factory. Confirm that contact surfaces are
not damaged and are clean and dry. Abrasives should
not be used on these surfaces because contact surfaces
are electroplated. Inspect joint insulators for cracking or
any sign of damage.
Megger each busway component at 1000 volts, phase
to phase and phase to ground, to verify insulation
integrity. Minimum readings should be no less than:
Megohms = 200 / length of run in feet
Or
= 66 / length of run in meters
If readings are below this minimum, do not apply power
to the installed busway and contact Siemens.
2

4.0 XJ-L Busway Plug-In-Duct (X100, X200, X400)
INSTALLATION INSTRUCTIONS
4.0.1 TO JOIN 2 SECTIONS OF XJ-L BUSWAY:
4.0.1.1 For normal edgewise mounting, the word "TOP" (A) is up.
(See Fig.1)
4.0.1.2 Loosen screws "B" and remove the external housing
connectors. (See Fig. 1)
4.0.1.3 Assemble the plain end to the insulator end by aligning the
holes in the housing ends. Slide the two sections together
until the housing holes are in line. (See Fig. 2) The joint
inspection cover must be rotated open. Press the bus bars
completely into the spring clips.
4.0.1.4 Re-install the external housing connectors so that the guide
pins engage the holes in the housings and tighten screws "B"
to 20 IN-LBS.
4.0.1.5 Verify that the bus bars are fully seated in the spring clips.
4.0.1.6 For X400 busway, install the removable joint clip assembly
by aligning the assembly over the joint inspection opening
and pushing it on to the bus bars until it is just below the
surface of the housing. TIP: Apply pressure to either side
of the assembly, left hand and then right hand until fully
seated.
4.0.1.7 Close joint inspection cover and secure it with provided
hardware. The joint is now complete.
4.1 Hanger Instructions (XH2, XH3)
4.1.1 TO HANG XJ-L BUSWAY FROM DROP RODS:
4.1.1.1 Position drop rods as required. (Max 10' Spacing).
4.1.1.2 Using a double nut configuration, assemble the hanger
halves to each drop rod as shown. (See Fig. 3)
4.1.1.3 Spread the hanger open at the bottom and slip the duct up
into the hanger. For normal edgewise mounting, the word
"TOP" is up. Secure the hanger with the 1/4-20 hardware.
4.1.2 TO WALL-MOUNT XJ-L BUSWAY:
4.1.2.1 Attach one hanger half to wall as shown. (See Fig. 4)
4.1.2.2 Insert duct into hanger. For normal edgewise mounting, the
word "TOP" is up.
4.1.2.3 Assemble the hanger complete as shown using the 5/16-18
hardware on top and the 1/4-20 hardware on the bottom.
4.2 Wall Flange Instructions (WF1, WF2, WF3)
4.2.1 Place the flange halves around the duct where it passes
through the wall, floor, or ceiling. Using appropriate
hardware, attach flanges to wall, floor, or ceiling.
(See Fig. 6)
3
Figure 1
Figure 6
Figure 4
Figure 3
XH2 XH3
Figure 2

4
4.3 End Closer Instructions (XE100, XE200, XE400)
4.3.1 Remove external housing connectors if present. Loosen last
housing screws on top and bottom of duct. Slip end closer over
duct, engaging loosened screws. Tighten screws to retain end
closer. (See Figure 5)
Figure 5
X100, X200 X400
5.0 XJ-L Bus Plug Installation and Removal Instructions
5.1 General Information
5.1.1 XJ-L Bus plugs are available with molded case circuit breakers or Vacu-Break® fusible switches. Bus plugs may be
operated with a pull-chain or hookstick from the floor. Lightweight and portable, plugs are easily moved from one
location to another. Captive hardware allows for easy removal and re-installation.
5.1.2 The bus plug contact fingers are lubricated with an oxide inhibiting grease at the factory. This grease should not be
removed.
5.1.3 Types of XJ-L Bus Plugs:
XQ Series XQ-R Series XEC Series
3 Cir. XPM Series 6 Cir. XPM Series
XLEC Series XLVB Series

5
5.2 Bus Plug Installation Procedures
Note: The following are general procedures for installing all XJ-L Series bus plugs.
5.2.1 Ensure that the bus plug handle or breaker (if so equipped) is in the OFF position.
5.2.2 Back out all mounting screws. Screws should not be removed from the bus plug. Each plug has 1 or 2 mounting
screws on the left endwall that thread into the busway sidechannel. There are additional mounting/retaining
screws threaded into the top and/or bottom sides of the plug enclosure. These screw, when tightened, will lock the
bus plug enclosure onto the busway sidechannel.
5.2.3 Remove the XOC outlet cover (if so equipped). Locate the bus plug alignment finger slot in the lower left hand
corner of the busway outlet opening.
5.2.4 Locate the bus plug housing alignment tabs on the top of the bus plug. Position the bus plug over the
outlet opening with the bus plug housing alignment tabs resting on the top of the busway.
5.2.5 Guide the bus plug into the outlet opening, ensuring that the bus plug alignment finger and bus plug conductor
fingers enter their corresponding openings in the outlet.
5.2.6 Push the bus plug firmly into the busway plug-in outlet.
5.2.7 Make sure the bus plug is fully seated on the busway housing, and then tighten all mounting screws.
5.2.8 6 and 12 circuit XPMs are provided with drop rod brackets and require auxiliary support. Drop rod brackets can be
used with Siemens UJ100 Universal Hanger J-Hooks.
5.3 Bus Plug Removal Procedures
Note: The following are general procedures for removing all XJ-L Series bus plugs.
5.3.1 Ensure that the bus plug handle or breaker (if so equipped) is in the OFF position.
5.3.2 Unplug all power cables from receptacles (if so equipped).
5.3.3 Loosen all mounting/retaining screws and visually verify there is clearance between the retaining screws and the
busway sidechannel. Do not remove screws from bus plug.
5.3.4 Grasp both sides of the bus plug along the bottom edge, pull out, and then lift off of the busway.
5.3.5 Re-install the XOC outlet cover (if so equipped).
Typical XJ-L Bus Plug

6
6.0 Maintenance Procedures
6.0.1 Keep busway free of dust, dirt and/or foreign matter. Moisture from roof leaks or dripping pipes should be
eliminated. Should the busway become contaminated with water contact the local Siemens sales office.
6.0.2 Inspect the busway system periodically. An infrared thermometer may be used to thermally scan the run to identify
potential hot spots.
6.0.3 For general information regarding handling, installation, operating and maintenance of busway systems, refer to
NEMA Publication No. BU1.1.
6.1 De-energize the busway before performing any of the following
operations:
6.1.1 If there are signs of overheating, visually check for deterioration or contamination of insulation and contact
surfaces. Check tightness of nuts, bolts, etc.
6.1.2 Check for missing or broken parts, corrosion, wear, dirt or signs of arcing. Clean or replace parts as required. After
any repair or rework, isolate the busway and megger the busway system. Minimum readings should be no less
than:
Megohms = 200 / length of run in feet
or
= 66 / length of run in meters
Contact Siemens if readings are below this minimum.
THESE PROCEDURES DO NOT REPRESENT AN EXHAUSTIVE SURVEY OF MAINTENANCE STEPS NECESSARY TO ENSURE SAFE
OPERATION OF THE EQUIPMENT. PARTICULAR APPLICATIONS MAY REQUIRE ADDITIONAL PROCEDURES. SHOULD ADDI-
TIONAL INFORMATION BE DESIRED OR SHOULD PARTICULAR PROBLEMS ARISE WHICH ARE NOT COVERED SUFFICIENTLY
FOR THE PURCHASER'S PURPOSES, THE MATTER SHOULD BE REFERRED TO THE LOCAL SIEMENS SALES OFFICE, OR CALL 1-
800-241-4453 FOR EMERGENCY CUSTOMER SERVICE.
NOTE: THESE INSTRUCTIONS DO NOT PURPORT TO COVER ALL DETAILS OR VARIATIONS IN EQUIPMENT, NOR TO PROVIDE
FOR EVERY POSSIBLE CONTINGENCY TO BE MET IN CONNECTION WITH THE INSTALLATION, OPERATION OR MAINTENANCE
OF A SIEMENS BUSWAY SYSTEM. SHOULD ADDITIONAL INFORMATION BE DESIRED OR SHOULD PARTICULAR PROBLEMS
ARISE WHICH ARE NOT COVERED SUFFICIENTLY FOR THE PURCHASER'S PURPOSES, THE MATTER SHOULD BE REFERRED TO
THE LOCAL SIEMENS SALES OFFICE. THE CONTENTS OF THIS INSTRUCTION MANUAL SHALL NOT BECOME PART OF OR
MODIFY ANY PRIOR OR EXISTING AGREEMENT, COMMITMENT OR RELATIONSHIP. THE SALES CONTRACT CONTAINS THE
ENTIRE OBLIGATION OF SIEMENS. THE WARRANTY CONTAINED IN THE CONTRACT BETWEEN THE PARTIES IS THE SOLE
WARRANTY OF SIEMENS. ANY STATEMENTS CONTAINED HEREIN DO NOT CREATE NEW WARRANTIES OR MODIFY THE
EXISTING WARRANTY.
Siemens Industry Inc.
Spartanburg, S.C. 29304 USA