Siemens REV23 User manual

Symbols Absence 24-hour mode 2 heating
periods
“Time” menu Heating active Comfort
setpoint
3 heating
periods
T“Temperature”
menu Cooling active Economy setpoint Current weekday
“Heating
periods” menu
Automatic
operation
Setpoint frost
protection Workingday group
“Absence”
menu
Continuously
comfort mode
Setpoint remote
operation Weekend group
Battery
change
Continuously
economy mode
Absence
setpoint Entire week
Commissioning and quick start Remote
operation
Frost
protection
1 heating
period Time schedule
Functions of the roller selector
CLICK
Press:
•You access the menu
level
•You activate the menu
•You save the inputs
•You switch to the next
menu item
•You accept the menu
item
+
Roll:
•You go from one menu to the
next
•You change the setting
variables (temperature in
increments of 0.2 °C, time in
increments of hours and
minutes)
•You select predefined functions
1. Remove controller from its base and open cover
of the battery compartment.
2. Remove the black battery transit tab. The
controller will switch itself on.
3. Close the battery compartment and replace
the controller.
Escape button
Selecting the operating mode Press the Esc button to return to the menu level previously activated or to leave
the menu level in a number of steps until you reach the initial display
(the settings currently displayed will be accepted).
The operating mode selector enables you
to select 5 different operating modes: Setting the time of day and the weekday
•Automatic operation with a maximum of 3
heating / cooling periods
•Continuously comfort mode
•Continuously economy mode
•Continuously frost protection mode
•24-hour mode with current comfort setpoint
Changing temporarily the current
setpoint temperature
CLICK ð
hðhð
ðð
If no button is pressed for 10 seconds, the setting
displayed will be accepted and the initial display will
appear again.
1. Press: You access the menu level;
the clock flashes.
2. Press: You accept the menu;
the hours flash.
3. Roll: Set the current hour.
4. Press: You save the input;
the minutes flash.
5. Roll: Set the current minute.
6. Press: You save the input;
the weekday flashes.
7. Roll: Select the current weekday.
8. Press the Esc button to return to the menu level:
the Tmenu flashes
(change not necessarily required; press
the Esc button again to return to the
initial display).
° C
The change is
maintained until
the next
switching point is
reached! Changing temperatures long-term
1. When pressing the or button for the
first time, the currently valid setpoint temperature
will be displayed. It can be readjusted in
increments of 0.2 °C (max. +/-4 °C).
2. After 3 seconds, the initial display will
automatically appear again.
Changing temporarily the
temperature setpoint (savings tip)
CLICK ðð
ð° C ð
ð° C ðð
° C ðð
° C
ðð
If no button is pressed for 10 seconds, the setting
displayed will be accepted and the initial display will
appear again.
1. Press: You access the menu level;
the clock flashes.
2. Roll: Toward the display to the T menu.
3. Press: You accept the menu;
symbol flashes.
4. Press: You accept ;
the setpoint flashes.
5. Roll: Set the comfort temperature
6. Press: You save the input;
symbol flashes.
7. Press: You accept ; the setpoint flashes.
8. Roll: Set the economy temperature.
9. Press: You save the input;
symbol flashes.
10. Press: You accept ; the setpoint flashes.
11. Roll: Set the frost protection temperature.
12. Press: You save the input; symbol
flashes.
13. Press: You accept ; the setpoint flashes.
14. Roll: Set the temperature setpoint
while remote operation is active.
15. Press the Esc button to return to the menu level:
The heating periods menu flashes
(Change not necessarily required; press
the Esc button again to return to the
initial display.)
In operating modes and , this
button can be pressed to make a manual
change from comfort to economy mode,
or vice versa. The change will
automatically be cancelled when
reaching the next switching point or
when selecting another operating mode.
Siemens SBT / HVAC Products CE1B2264en 12.03.2002
en
Operating Instructions
REV23
All manuals and user guides at all-guides.com
all-guides.com

Settings for automatic operation with 2 heating periods 24-hour operation
24-hour operation with only one heating period (the
heating period will automatically be generated from
the current 24-hour program).
Start of the first heating period, end of the second
heating period, plus the currently adjusted comfort
temperature setpoint.
Retrieving the default values
Press the button behind the small opening for at
least one second, thus resetting the user-specific
settings to their default values (the heating engineer
settings will remain unchanged).
The clock starts at 12:00.
When making a reset, all display fields will light up.
Default values
Factory settings for heating
Operating mode
Start of continuous operation 00:00 00:00 00:00
End of continuous operations 24:00 24:00 24:00
Setpoint of comfort mode 19 °C
Setpoint of economy mode 16 °C
Setpoint frost protection 5 °C
Setpoint
remote operation 10 °C
Setpoint
absence 12 °C
Operating mode
Selected periods
Start of period 1 07:00 06:00 06:00
End of period 1 23:00 08:00 08:00
Start of period 2 17:00 11:00
End of period 2 22:00 13:00
Start of period 3 17:00
CLICK ð
ðð
ðð
hð
hð
° C
ð
ð
hð
hð
° C ð
ðð
/ð
If no button is pressed for 10 seconds, the setting
displayed will be accepted and the initial display
restored.
1. Press: You access the menu level;
the clock flashes.
2. Roll: Twice toward the display;
menu flashes.
3. Press: You accept the menu;
the day selection symbol
flashes.
4. Roll: Select the days, the working days, the
weekend or the week.
5. Press: You save the selection made;
heating period flashes.
6. Press: Accept ; heating period 1 flashes.
7. Press: You accept heating period 1;
start time of heating period 1 flashes.
8. Roll: Set the start time of heating period 1.
9. Press: You save the input;
end time of heating period 1 flashes.
10. Roll: Set the end time of heating period 1.
11. Press: You save the input;
setpoint of heating period 1 flashes.
12. Roll: Set the setpoint of heating period 1.
13. Press: You save the input;
heating period 2 flashes.
14. Press: You accept heating period 2;
start time of heating period 2 flashes.
15. Roll: Set the start time of heating period 2.
16. Press: You save the input;
end time of heating period 2 flashes.
17. Roll: Set the end time of heating period 2.
18. Press: You save the input;
setpoint of heating period 2 flashes.
19. Roll: Set the setpoint of heating period 2.
20. Press the Esc button to return to the heating
periods menu:
Menu item heating periods
flashes.
21. Roll: Toward the display or away from it to
menu item or heating periods
(Change not necessarily required; press
the Esc button several times to leave
the menu level in several steps, thus
returning to the initial display.)
End of period 3 22:00
Setpoint of period 1 19 °C 19 °C 19 °C
Settings for automatic operation with 1 or 3 heating periods Setpoint of period 2 20 °C 20 °C
Setpoint of period 3 21 °C
The procedure to be followed is the same as that for automatic operation with 2 heating periods the only
difference being that, in addition, a setpoint for heating period 3 can be entered (standard setting 21 °C). Setpoints and See above
Absence / holidays Default values
Factory settings for cooling
Operating mode
Setpoint 23 °C 23 °C 29 °C 35 °C
Setpoint
remote operation 30 °C
Setpoint
absence 30 °C
Changing the batteries
2 Alkaline batteries type AA 1.5 V
1. Press: You access the menu level;
the clock flashes.
2. Roll: Away from the display,
menu flashes.
3. Press: Accept ;
symbol flashes.
4. Roll: Set the start (weekday) of your
absence.
5. Press: You save the input;
the number of days flash.
6. Roll: Set the duration of your absence;
number of days (max. 99)
7. Press: You save the input;
setpoint flashes.
8. Roll: Set the temperature.
9. Press the Esc button to return to the menu level;
the clock flashes.
(Change not necessarily required; press
the Esc button again to return to the
initial display.)
When this symbol appears, the batteries must be
replaced within 3 months.
1. Remove controller from its base.
2. Open battery compartment at the rear and
replace the batteries.
3. Close battery compartment and replace the
controller.
Note:
When changing the batteries, the current data are
maintained for a maximum of one minute.
CLICK ð
ðð
ð° C
ðð
If no button is pressed for 10 seconds, the setting
displayed will be accepted and the initial display will
appear again.
Siemens SBT / HVAC Products CE1B2264en 12.03.2002
All manuals and user guides at all-guides.com