Siemens DESIGIO 30 User manual

Siemens Building Technologies CA2N3295E / 03.1999
Landis & Staefa Division 1/4
3295
DESIGO 30
Service terminal BCS
Hand-held terminal with three operating levels, easy-to-read display panel and
user-friendly key pad, for commissioning, tuning and servicing of HVAC systems
incorporating controllers in the DESIGO 30 range.
The service terminal is connected to the LON bus, so allowing the user access
(depending on operating level) to the data from the connected DESIGO 30 devices.
The basic procedure for operation is as follows:
Menu and data points are selected using the four navigation keys. Selected points are
displayed in inverse video, and adjustable values can be modified with the +and –
keys. Modified values are accepted with enter , and functions are terminated with the
esc key.
50169A
?
esc
+
–
1
2
3
4
Key
1 Display
2 Info key
3 Edit keys
4 Navigation keys
Operating level 1: (level on start-up): For access to all the controller values needed
for normal operation (plant status, all inputs and outputs, set-
points and time programmes). Simple commissioning using the
check lists.
Operating level 2: Controller tuning based on the check list.
Operating level 3: Access to all controller data (for specially trained service
engineers and system contractors).
Factory settings:
– Operating level 1 = A
– Operating level 2 = B
– Operating level 3 = C
Use / Functions
Operating levels
Password

CA2N3295E / 03.1999 Siemens Building Technologies
2/4 Landis & Staefa Division
The BCS is designed primarily as a hand-held operator terminal. As an alternative, a
bracket is available, which can be screwed onto any surface. The service terminal can
be clipped onto this bracket when not in use. The BCS may, however, also be mounted
in a control panel front, if required. The service cable, which incorporates the LON bus
and power supply, can be plugged into the service socket of a controller.
– Case for protection of service terminal (e.g. in tool boxes) and User Manual, R23
– Service cable, 3 m long
– Wall bracket. See Manual R21 section 04.20 for detailed installation instructions.
Overview
Overview
Device list
Overview
Device 1 (RC.., BCE, BCS, APED30)
60269EN
Device n
BCS settings
Operating level
Subnet selection
Comms. protocol
Data representation
Language information
Definition devices
Device registration
Remove device
Alarms / Network time
Last 32 alarms
Set bus time / date
Overview
(e.g. RCK-WU)
Important datapoints
Week program
Date program
Proportional seq. Y1
Proportional seq. Y3
Proportional seq. Y5
Value of cascade
Setpoint reset
Regulation sensor X1
Shift sensor X2
Setpoint External
Output Heating Y1
Output Cooling Y3
Output heat Y5
Output Digital Y2
Alarm
Output Clock
Frost sensor X4
Output Frost
Control relay Step 1
Control relay Step 2
Structure data
Alarm summaries
Device data
Internal setting
Overview
OverviewOverview
Check network
Operating level 1
Operating level 2
Operating level 3
2)
3)
2)
2)
2)
2)
3)
3)
3)
2)
2) 2)
2)
2)
2)
2)
2)
2)
2)
2)
2)
3)
3)
3)
3)
3)
3)
3)
3)
3)
3)
3)
3)
3)
Display
The display window accommodates 10 lines of
26 characters each. The first two lines display the
controller and the menu option. The remaining
eight lines are used to display the data
associated with the selected menu.
Fields and symbols
5051 1
defca
ggbb
Field Symbol Description
a Path (two lines)
b Data field (eight lines)
a / b Forced value
Alarm
Unstructured controller
Undefined device
Battery discharged
cMore data to the left
d More data to the right
eBCS busy
Activity on bus
Bus error
fAlarm received
gPosition indicators, more data in direction of arrow
Mounting
Accessories
Operating notes
Menu tree
Display and indication

Siemens Building Technologies CA2N3295E / 03.1999
Landis & Staefa Division 3/4
Key Description
Navigation
keys Select menu item
Edit keys Modify data in selected menu (modifiable data is shown in
inverse video):
+ – Increase / decrease value or On / Off
↵enter: Transmit the data entered
esc Terminate function (without transmitting any data entered)
Info key ?Display codes or abbreviations in full (Hold key down; the
information remains in the display window until the Info key is
released)
Fast keys
The navigation keys and the + and – keys have a double action: light pressure for
slow, and heavy pressure for fast operation. This allows you to jump quickly from a
menu option or data point to the next, or to the bottom of the display.
50503EN
Device list
Overview
001:Ventilation East
001:Ventilation West
001:Heating system A
002:Heating system B
003:Heating,basement
On start-up, the BCS display provides an overview of
the devices connected to the bus. Use the navigation
keys to select a device. The selected device will be
shown in inverse video. Use enter to jump to the
relevant menu. Press ?to display detailed
information about the selected item.
50504EN
BCS Settings
Operating level
Password ?
> <
ABCDEFGHIJKLMNOPQRSTUVWXYZ
abcdefghijklmnopqrstuvwxyz
0123456789+–_/!•?$äöü
Use the navigation keys to select the letters or
numbers required, and press +to write them in the
data entry field or –to delete them. When you leave
the data field after making changes to the name, you
will be asked to confirm the data entered. Press
enter to complete the input process. The same dis-
play is used to enter a unique name when registering
a device on the bus, and for password entry.
50505Aen
X1 =21.0°C
X2 =14.0°C
X3 =23.0°C
X4 =10.0°C
Y1 =5.3V
Y3 =0.0V
FRIND =On
Y2 =0.0V
Ventilation East
Important datapoints
YD1 =On
YD2 =Off
CLCK =Auto I
W =20.0°C
MODE =Auto
XB =5.0°C
XON =5.0°C
FCOF =1.0K
Modifying a value:
Use the navigation keys to select the value. If modi-
fiable, the value will be displayed in inverse video.
Prepare to modify value by pressing +/ –. The value
will flash. Modify the value with +/ –keys. Accept
the new value with enter or press esc to abandon
the new value (the original value will be retained).
Ventilation East
Week programme
Mo Tu We Th Fr Sa Su
06:00 On
21:30 Off
--:-- ----
Copy to : ...
50506Aen
0 2 4 6 8 10 12 14 16 18 20 22 24
When a day is selected with the navigation keys, the
associated switch programme will be displayed
automatically. The days are also marked (with thick
or thin bars) to display the switch-on and switch-off
times graphically. To define a time programme, enter
the switch-on and switch-off times with the +/ –
keys and confirm with enter. To copy a complete
switch programme, move to the "Copy to ..." option
and use the +/ –keys to select the day. Press
enter to accept. To delete switch times, use the –
key to set switch states to – – – and press enter.
Ventilation East
Date programme
JUNE
1995 56 7 8 9 10 11
12 14 15 16 17 18
19
26
50502EN
27 28 29 30
13
20 21 22 23 25 24
Mo Tu We Th Fr Sa Su
1 2 3 4
To define a date programme, select the required
date with the navigation keys and set with +or delete
with the –key. When you leave this option you will
be asked to confirm the data entered. Acknowledge
with enter. Use the navigation keys (left, right, down)
to move to the previous or next month. Use esc or
the up-navigation key to exit to the path area.
Keypad
Examples of display
and operation
Start-up
Changing the
operating level
Two-column table
Week (7-day)
programme
Date programme

CA2N3295E / 03.1999 Siemens Building Technologies
4/4 Landis & Staefa Division
V
50507EN
8
-30
4
0K
30
Ventilation East
Proportional sequence Y1
K
22
50508EN
-10 32 °C
252
Ventilation East
Setpoint reset
Changing a value on the graph:
Select the value with the navigation keys. If it is
modifiable, the value will be shown in inverse video.
Prepare the modification with +/ –. The value will
flash. Modify the value with the +/ – keys.
Press enter to adopt the new value, or press esc to
abandon it (the original value will be retained).
Supply voltage Low voltage (SELV)
Nominal voltage AC 24 V, 50/60 Hz
– Admissible tolerance +15 / –10 %
Power consumption Max. 200 mA
Connection RJ45 socket
Service cable 3 m, RJ45 connector at each end (comms and power)
LON with BACnet protocol
– Connection 2-wire (comms only, without AC 24 V)
– Max. cable length 1100 m (unscreened)
– Bus termination On rear, set by switch
Weight (excluding packaging) 0.38 kg
Dimensions (W x H x D) 110 x 210 x 45 mm
Cleaning Use a damp cloth only. Use soap or solvent only.
Do not allow moisture to enter the housing.
Conditions of use For indoor use
Temperature range
– Operation 5 ... 45 °C
– Storage –25 ... 70 °C
Ambient humidity 10 ... 90 %rh, non-condensing
Product safety EN 61010-1
– Overvoltage category II
– Contamination level 2
Electrical safety SELV-E (PELV to IEC 364-4-41)
Conformity This product meets the requirements for CE marking
VED
All dimensions in mm
5061 1
110
210
45
50612
85
130
47
Graphics
Technical data
Power supply
Connection
Communication
Weight / Dimensions
Cleaning
General ambient conditions
Safety
Dimensions
1999 Siemens Building Technologies Ltd. Replaces R21-07.50
Wall bracket