Siemens SIMATIC NET SFP Series User manual

Transceiver SFP/SFP+/SCP/STP
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
SIMATIC NET
Network components
Transceiver SFP/SFP+/SCP/STP
Operating Instructions
11/2015
A5E02630804
-08
Introduction
1
Safety notes
2
Description
3
Assembling
4
Uninstalling
5
Connecting up
6
Technical data
7
Dimension drawings
8
Approvals
9

Siemens AG
Division Process Industries and Drives
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E02630804-08
Ⓟ
11/2015 Subject to change
Copyright © Siemens AG 2011 - 2015.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance a
re required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

Transceiver SFP/SFP+/SCP/STP
Operating Instructions, 11/2015, A5E02630804-08 3
Table of contents
1 Introduction............................................................................................................................................. 5
2 Safety notes............................................................................................................................................ 7
3 Description.............................................................................................................................................. 9
3.1 Type designation.......................................................................................................................9
3.2 Product overview ....................................................................................................................10
3.3 Components of the product ....................................................................................................12
4 Assembling ........................................................................................................................................... 13
4.1 Notes on installation of SFP / SFP+ transceivers...................................................................13
4.2 Inserting an SFP / SFP+ transceiver ......................................................................................17
4.3 Notes on installation of SCP / STP transceivers ....................................................................18
4.4 Inserting an SCP / STP transceiver ........................................................................................19
5 Uninstalling ........................................................................................................................................... 21
5.1 Removing an SFP / SFP+ transceiver....................................................................................21
5.2 Removing an SCP / STP transceiver......................................................................................21
6 Connecting up....................................................................................................................................... 23
6.1 Notes on commissioning.........................................................................................................23
6.2 Power supply ..........................................................................................................................23
7 Technical data ...................................................................................................................................... 25
7.1 Mechanical and electrical data ...............................................................................................25
7.2 Cable lengths ..........................................................................................................................28
7.3 Other properties ......................................................................................................................30
8 Dimension drawings.............................................................................................................................. 31
8.1 SFP dimension drawing ..........................................................................................................31
8.2 SFP+ dimension drawing........................................................................................................32
8.3 SCP dimension drawing..........................................................................................................33
8.4 STP dimension drawing ..........................................................................................................34
9 Approvals.............................................................................................................................................. 35
Index..................................................................................................................................................... 41

Table of contents
Transceiver SFP/SFP+/SCP/STP
4Operating Instructions, 11/2015, A5E02630804-08

Transceiver SFP/SFP+/SCP/STP
Operating Instructions, 11/2015, A5E02630804-08 5
Introduction
1
Purpose of the compact operating instructions
Based on the compact operating instructions, you will be able to install the SFP, SFP+, SCP
and STP transceivers. The configuration and the integration of the devices in a network are
not described in these instructions.
Validity of these compact operating instructions
These compact operating instructions apply to the SFP, SFP+, SCP and STP product group.
Further documentation
In the system manuals "Industrial Ethernet / PROFINET Industrial Ethernet" and "Industrial
Ethernet / PROFINET passive network components", you will find information on other
SIMATIC NET products that you can operate along with the devices of this product line in an
Industrial Ethernet network.
There, you will find among other things optical performance data of the communications
partner that you require for the installation.
You will find the system manuals here:
●On the data medium that ships with some products:
–Product CD / product DVD
–SIMATIC NET Manual Collection
●On the Internet pages of Siemens Industry Online Support under the following entry IDs:
–27069465 (http://support.automation.siemens.com/WW/view/en/27069465)
Industrial Ethernet / PROFINET Industrial Ethernet System Manual
–84922825 (http://support.automation.siemens.com/WW/view/en/84922825)
Industrial Ethernet / PROFINET - Passive network components System Manual
SIMATIC NET manuals
You will find the SIMATIC NET manuals here:
●On the data medium that ships with some products:
–Product CD / product DVD
–SIMATIC NET Manual Collection
●On the Internet pages of Siemens Industry Online Support
(http://support.automation.siemens.com/WW/view/en/10805878/130000).

Introduction
Transceiver SFP/SFP+/SCP/STP
6Operating Instructions, 11/2015, A5E02630804-08
SIMATIC NET glossary
Explanations of many of the specialist terms used in this documentation can be found in the
SIMATIC NET glossary.
You will find the SIMATIC NET glossary here:
●SIMATIC NET Manual Collection or product DVD
The DVD ships with certain SIMATIC NET products.
●On the Internet under the following entry ID:
50305045 (http://support.automation.siemens.com/WW/view/en/50305045)
Unpacking and checking
WARNING
Do not use any parts that show evidence of damage
If you use damaged parts, there is no guarantee that the device will function according to
the specification.
If you use damaged parts, this can lead to the following problems:
•Injury to persons
•Loss of the approvals
•Violation of the EMC regulations
•Damage to the device and other components
Use only undamaged parts.
1. Make sure that the package is complete.
2. Check all the parts for transport damage.
Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, solutions, machines, equipment and/or networks. They are
important components in a holistic industrial security concept. With this in mind, Siemens’
products and solutions undergo continuous development. Siemens recommends strongly
that you regularly check for product updates.
For the secure operation of Siemens products and solutions, it is necessary to take suitable
preventive action (e.g. cell protection concept) and integrate each component into a holistic,
state-of-the-art industrial security concept. Third-party products that may be in use should
also be considered. For more information about industrial security, visit
http://www.siemens.com/industrialsecurity.
To stay informed about product updates as they occur, sign up for a product-specific
newsletter. For more information, visit http://support.automation.siemens.com.

Transceiver SFP/SFP+/SCP/STP
Operating Instructions, 11/2015, A5E02630804-08 7
Safety notes
2
Safety notices on the use of the devices
The following safety notices must be adhered to when setting up and operating the device
and during all associated work such as installation, connecting up, replacing devices or
opening the device.
General notices regarding use in hazardous areas
WARNING
Risk of explosion when connecting or disconnecting the device
EXPLOSION HAZARD
DO NOT CONNECT OR DISCONNECT EQUIPMENT WHEN A FLAMMABLE OR
COMBUSTIBLE ATMOSPHERE IS PRESENT.
WARNING
Replacing components
EXPLOSION HAZARD
SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I, DIVISION
2 OR ZONE 2.
WARNING
Requirements for the cabinet/enclosure
When used in hazardous environments corresponding to Class I, Division 2 or Class I,
Zone 2, the device must be installed in a cabinet or a suitable enclosure.
Notices for use in hazardous areas according to ATEX
WARNING
Requirements for the cabinet/enclosure
To comply with EU Directive 94/9 (ATEX95), this enclosure must meet the requirements of
at least IP54 in compliance with EN 60529.

Safety notes
Transceiver SFP/SFP+/SCP/STP
8Operating Instructions, 11/2015, A5E02630804-08
WARNING
Suitable cables for temperatures in excess of 70 °C
If the cable or conduit entry point exceeds 70 °C or the branching point of conductors
exceeds 80 °C, special precautions must be taken. If the equipment is operated in an air
ambient in excess of 50 °C, only use cables with admitted maximum operating temperature
of at least 80 °C.
WARNING
Protection against transient voltage surges
Provisions shall be made to prevent the rated voltage from being exceeded by transient
voltage surges of more than 40%. This criterion is fulfilled, if supplies are derived from
SELV (Safety Extra-Low Voltage) only.

Transceiver SFP/SFP+/SCP/STP
Operating Instructions, 11/2015, A5E02630804-08 9
Description
3
3.1
Type designation
Structure of the type designation
The type designation of an pluggable transceiver is made up of several parts that have the
following meaning:
Interface *)
Property
[-]
100 Mbps LC port optical, multimode, up to max. 5 km.
1000 Mbps LC port optical, multimode, up to max. 750 m.
LD
100 Mbps LC port optical, single mode fiber-optic cables, up to max. 26 km.
1000 Mbps LC port optical, single mode fiber-optic cables, up to max. 10 km.
LH
1000 Mbps LC port optical, single mode, up to max. 40 km.
LH+
100 Mbps LC port optical, single mode, up to max. 70 km.
1000 Mbps LC port optical, single mode, up to max. 70 km.
ELH200
100 Mbps LC port optical, single mode, up to max. 200 km.
ELH 1000 Mbps LC port optical, single mode, up to max. 120 km.
*
)
LD (Long Distance ), LH (Long Haul), LH+ (Long Haul +), ELH (Extreme Long Haul)

Description
3.2 Product overview
Transceiver SFP/SFP+/SCP/STP
10 Operating Instructions, 11/2015, A5E02630804-08
3.2
Product overview
Note
Fiber monitoring
All pluggable transceivers are capable of diagnostics and support fiber monitoring.
SFP transceiver
Type
Properties
Article number
SFP991-1 *
1 x 100 Mbps, LC port optical for glass FO cable
(multimode), up to max. 5 km
6GK5 991-1AD00-8AA0
SFP991-1LD * 1 x 100 Mbps LC port optical for glass FO cable
(single mode) up to max. 26 km
6GK5 991-1AF00-8AA0
SFP991-1LH+ * 1 x 100 Mbps LC port optical for glass FO cable
(single mode) up to max. 70 km
6GK5 991-1AE00-8AA0
SFP991-1ELH200 * 1 x 100 Mbps LC port optical for glass FO cable
(single mode) up to max. 200 km
6GK5 991-1AE30-8AA0
SFP992-1 1 x 1000 Mbps, LC port optical for glass FO
cable (multimode), up to max. 750 m
6GK5 992-1AL00-8AA0
SFP992-1LD 1 x 1000 Mbps LC port optical for glass FO
cable (single mode) up to max. 10 km
6GK5 992-1AM00-8AA0
SFP992-1LH 1 x 1000 Mbps LC port optical for glass FO
cable (single mode) up to max. 40 km
6GK5 992-1AN00-8AA0
SFP992-1LH+ 1 x 1000 Mbps LC port optical for glass FO
cable (single mode) up to max. 70 km
6GK5 992-1AP00-8AA0
SFP992-1ELH 1 x 1000 Mbps LC port optical for glass FO
cable (single mode) up to max. 120 km
6GK5 992-1AQ00-8AA0
* Cannot be operated in SFP+ slots.
Note
Only the following transceivers are permitted for the SCALANCE W786
-2 SFP:
•
SFP992-1
•
SFP992-1LD
•
SFP992-1LH
•
SFP992-1LH+
•
SFP992-1ELH

Description
3.2 Product overview
Transceiver SFP/SFP+/SCP/STP
Operating Instructions, 11/2015, A5E02630804-08 11
SFP+ transceiver
Type
Properties
Article number
SFP993-1 1 x 10 Gbps, LC port optical for glass FO
cable (multimode), up to max. 300 m
6GK5 993-1AT00-8AA0 1)
1 x 10 Gbps, LC port optical for glass FO
cable (multimode), up to max. 300 m
6GK5 993-1AT10-8AA0 2)
SFP993-1LD 1 x 10 Gbps, LC port optical for glass FO
cable (single mode), up to max. 10 km
6GK5 993-1AU00-8AA0 1)
1 x 10 Gbps, LC port optical for glass FO
cable (single mode), up to max. 10 km
6GK5 993-1AU10-8AA0 2)
SFP993-1LH 1 x 10 Gbps, LC port optical for glass FO
cable (single mode), up to max. 40 km
6GK5 993-1AV00-8AA0 1)
Can only be operated in SFP+ slots.
Note
1)Restriction with SFP+ transceivers for SCALANCE XR526-8C
If you use SFP+ transceivers identified with
1) with the SCALANCE XR526-
8C, the maximum
ambient temperature is reduced to 50
℃.
Note
2)Restriction for DFP+ transceivers for SCALANCE XR526-8C (2 x 24 VDC)
If you use SFP+ transceivers identified with
2) with the SCALANCE XR526-8C (2 x 24 VDC),
the maximum ambient temperature is reduced to 60
℃.
SCP / STP transceiver
Type
Properties
Article number
SCP992-1 1 x 1000 Mbps SC port optical for glass FO cable
(multimode) up to max. 750 m
6GK5 992-1AJ00-8AA0
SCP992-1LD 1 x 1000 Mbps SC port optical for glass FO cable
(single mode) up to max. 10 km
6GK5 992-1AK00-8AA0
STP991-1 1 x 100 Mbps ST port optical for glass FO cable
(multimode) up to max. 5 km
6GK5 991-1AB00-8AA0
STP991-1LD 1 x 100 Mbps ST port optical for glass FO cable
(single mode) up to max. 26 km
6GK5 991-1AC00-8AA0
Can only be operated in SCP and STP slots.

Description
3.3 Components of the product
Transceiver SFP/SFP+/SCP/STP
12 Operating Instructions, 11/2015, A5E02630804-08
Media modules
Note
The SFP media modules MM992
-2SFP may only be fitted with approved transceivers. The
media module can be fitted with up to two pluggable transceivers.
The SFP media modules MM99
2-4SFP may only be fitted with approved transceivers. The
media module can be fitted with up to four pluggable transceivers.
Type
Properties
Article number
Labeling on the
device
MM992-2SFP 2 x 100 / 1000 Mbps, SFP media module 6GK5 992-2AS00-
8AA0
9922AS
MM992-4SFP 4 x 100 / 1000 Mbps, SFP media module 6GK5 992-4AS00-
8AA0
9924AS
3.3
Components of the product
●Transceiver
●Information sheet

Transceiver SFP/SFP+/SCP/STP
Operating Instructions, 11/2015, A5E02630804-08 13
Assembling
4
4.1
Notes on installation of SFP / SFP+ transceivers
General notes on media modules and pluggable transceivers
WARNING
Install and remove media modules only when the power is off
Media modules may only be inserted in or removed from a SCALANCE device when the
power supply to the device has been turned off.
Use only approved media modules
Use only "MM900" media modules in the module slots of SCALANCE devices.

Assembling
4.1 Notes on installation of SFP / SFP+ transceivers
Transceiver SFP/SFP+/SCP/STP
14 Operating Instructions, 11/2015, A5E02630804-08
CAUTION
Remember the orientation of media modules.
On modular devices, there are always two module slots arranged opposite each other.
Remember the correct orientation when installing MM900 media modules.
Example:
•The first MM900 media module is installed in slot 1.
•The second MM900 media module installed in slot 2 must be turned through 180
degrees.
On modular devices for rack mounting, pairs of module slots are located one above the
other in which modules can be inserted in a specific order:
Example of a rack device:
•The first MM900 media module is installed in slot 1.
•The second MM900 media module installed in slot 7 must be turned through 180
degrees.
Other modules are then inserted in slots 2 and 8 or 3 and 9 etc.
The permitted operating temperature is decided by the fully equipped device (switch +
media module + pluggable transceiver).
With modular devices, it is not only the switch that decides the permitted operating
temperature of the overall device but also the temperature ranges of the MM900 media
modules and the SFP transceivers. You will find details in the technical specifications of the
relevant components.
The following aspects can restrict the maximum permitted operating temperature:
•The orientation of the carrier device.
•The use of SFP transceivers.
•The use of transceivers of the types LH, LH+ or ELH.
NOTICE
Use only approved pluggable transceivers
If you use components not approved by Siemens AG, in particular SFP / SFP+
transceivers, Siemens cannot accept any responsibility for the correct functioning of the
"Ethernet switch system" according to the specification.
If components are used that have not been Siemens approved, Siemens cannot vouch for
their compatibility or for risk-free use of these components.

Assembling
4.1 Notes on installation of SFP / SFP+ transceivers
Transceiver SFP/SFP+/SCP/STP
Operating Instructions, 11/2015, A5E02630804-08 15
Note
Use media modules only in an approved modular device
Use an MM900 media module only for a device equipped with suitable slots for such
modules. Example: X308
-2M.
The names and labeling of the media modules differ
•
Example: The device is called, for example, "MM992-2SFP" [6GK5 992-2AS00-8AA0],
the labeling on the device is "9922AS". You will find detailed information on the labeling
of the media modules in the "MM900 media modules" compact operating instructions.
Note
Shipbuilding approval
The shipbuilding approval applies to all SFP pluggable transceivers.
Note
Slot number
With modular devices, the MM900 media modules must be given a slot number.
The slot number labels are supplied with the modular devices.
Note
Different colors of the clip
An SFP with multimode has a black clip and an SFP with single mode has a blue clip. To
protect the pins, these are fitted with a dummy plug.
Note
Plugging and pulling during operation
With SCALANCE X, the pluggable transceivers can be plugged and pulle
d during operation.
If you have questions on the use of SIMATIC NET products, please contact your Siemens
sales partner.

Assembling
4.1 Notes on installation of SFP / SFP+ transceivers
Transceiver SFP/SFP+/SCP/STP
16 Operating Instructions, 11/2015, A5E02630804-08
Notes on SCALANCE X-300
Note
Pluggable transceivers with the SCALANCE XR324-4M EEC
In contrast to the information in the product documentation for the SCALANCE MM900,
MM992
-2SFP media modules can be operated in the SCALANCE XR324-4M EEC at
ambient temperatures up to a maximum of 70
°C if the following requirements are met:
•
MM992-2SFP media modules as of hardware product version 02 are suitable. The
hardware product version can be found on the device. You can also read out this
information with the WBM or the CLI.
•
Only the following pluggable transceivers may be used:
–SFP991-1
–SFP991-1LD
–SFP992-1
–
SFP992-1LD
Notes on SCALANCE XR-500
Note
Fixed slots of the SCALANCE XR-500
The SFP+ transceivers are not suitable for media modules. The SCALANCE
- XR500 has
four fixed slots for SFP+.
It is, however, possible to operate SFP transceivers in the fixed SFP+ slots of the device.
Note that the SFP+ slots only support SFP transceivers with a transmission rate of 1000
Mbps.
Notes on SCALANCE W:
Note
With a SCALANCE W786-2, do not plug or pull an SFP transceiver during operation!
If you have questions on the use of SIMATIC NET products, please contact your Siemens
sales partner.

Assembling
4.2 Inserting an SFP / SFP+ transceiver
Transceiver SFP/SFP+/SCP/STP
Operating Instructions, 11/2015, A5E02630804-08 17
4.2
Inserting an SFP / SFP+ transceiver
Figure 4-1 Inserting an SFP / SFP+ transceiver
Follow the steps below to insert an SFP / SFP+ transceiver:
1. Remove the sealing plug of the SFP / SFP+ transceiver.
2. Close the clip of the SFP / SFP+ transceiver.
3. Insert the SFP / SFP+ transceiver in the SFP / SFP+ slot until you hear it engage, see
figure.
The SFP / SFP+ transceiver is then firmly secured.
4. Insert the connecting cable into the SFP / SFP+ transceiver until you hear it engage.
The connecting cable is then firmly secured.

Assembling
4.3 Notes on installation of SCP / STP transceivers
Transceiver SFP/SFP+/SCP/STP
18 Operating Instructions, 11/2015, A5E02630804-08
4.3
Notes on installation of SCP / STP transceivers
General notes on pluggable transceivers
NOTICE
Use only approved pluggable transceivers
If you use components not approved by Siemens AG, in particular SCP / STP transceivers,
Siemens cannot accept any responsibility for the correct functioning of the "Ethernet switch
system" according to the specification.
If components are used that have not been Siemens approved, Siemens cannot vouch for
their compatibility or for risk-free use of these components.
Note
Shipbuilding approval
The shipbuilding approval applies to all SCP / STP transceivers.
Note
Plugging and pulling during operation
The pluggable transceivers can be plugged and pulled during operation. If you have
questions on the use of SIMATIC NET products, please contact your Siemens sales partner.
Notes on SCALANCE XM-400
Note
SCP / STP transceivers can only be used in the S
CP / STP slots of the SCALANCE XM408-
4C.
Notes on SCALANCE W:
Note
With a SCALANCE W786-2, do not plug or pull an SFP transceiver during operation!
If you have questions on the use of SIMATIC NET products, please contact your Siemens
sales partner.

Assembling
4.4 Inserting an SCP / STP transceiver
Transceiver SFP/SFP+/SCP/STP
Operating Instructions, 11/2015, A5E02630804-08 19
4.4
Inserting an SCP / STP transceiver
Figure 4-2 Inserting an SCP / STP transceiver
Follow the steps below to insert an SCP / STP transceiver:
1. Remove the sealing plug of the SCP / STP transceiver.
2. Hold the SCP / STP transceiver so that the slight protrusion is on the right, see figure.
3. Insert the SCP / STP transceiver in the SCP / STP slot in this position until you hear it
engage, see figure.
The SCP / STP transceiver is then firmly secured.
4. Insert the connecting cable into the SCP / STP transceiver until you hear it engage.
The connecting cable is then firmly secured.

Assembling
4.4 Inserting an SCP / STP transceiver
Transceiver SFP/SFP+/SCP/STP
20 Operating Instructions, 11/2015, A5E02630804-08