SIIG AV-GM07J3-S1 User manual

16x16 HDMI Deep Color & full 3D over single
Cat.X Matrix
To avoid EMI issue, complete STP Cat6 cable is strongly recommended!
P/N: AV-GM07J3-S1

Safety and Notice
The AV-GM07J3-S1 16x16 HDMI Deep Color & full 3D over single Cat.X matrix has been tested
for conformance to safety regulations and requirements, and has been certified for
international use. However, like all electronic equipments, the AV-GM07J3-S1 should be used
with care. Please read and follow the safety instructions to protect yourself from possible
injury and to minimize the risk of damage to the unit.
●Follow all instructions and warnings marked on this unit.
●Do not attempt to service this unit yourself, except where explained in this manual.
●Provide proper ventilation and air circulation and do not use near water.
●Keep objects that might damage the device and assure that the placement of this unit is on a
stable surface.
●Use only the power adapter and power cords and connection cables designed for this unit.
●Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the
device before cleaning.
TABLE OF CONTENTS
INTRODUCTION.................................................................................................................1
FEATURES.........................................................................................................................1
PACKAGE CONTENTS ......................................................................................................1
SPECIFICATIONS ..............................................................................................................2
PANEL DESCRIPTIONS.....................................................................................................4
Transmitting unit ► MA-5216C-TX..........................................................................4
Receiving unit ►MA-5288RX..................................................................................5
IR PASS-THROUGH...........................................................................................................6
HARDWARE INSTALLATION.............................................................................................7
CONNECTION DIAGRAM...................................................................................................8
OPERATION APPROACH..................................................................................................9
EDID LEARNING ..............................................................................................................23
FAQ...................................................................................................................................24
NOTICE ............................................................................................................................25
WARRANTY......................................................................................................................26

1
INTRODUCTION
The AV-GM07J3-S1 16x16 HDMI Deep Color & full 3D over single Cat.X matrix with bi-directional
IR provides the most flexible and cost effective solution in the market to route high definition video
sources plus multi-channel (up to 7.1-channel) digital audio from any of the four HDMI sources to
the remote displays at the same time. Through only one low cost Cat-5/5e/6 LAN cables, not only
high quality video and audio can be transmitted to the display sites, but also users can switch
among four HDMI sources using the push-in button or remote control. Furthermore, the built-in IR
extension function makes users at display site access the DVD player, PS3 or any HDMI supported
devices directly!
FEATURES
●Support HDMI Deep Color & full 3D
●HDCP compliant
●Allows any source to be displayed on multiple displays at the same time
●Allows any HDMI display to view any HDMI source at any time
●Supports 7.1 channel digital audio
●Supports default HDMI EDID and learns the EDID of displays
●Supports full frequency IR signal from 20KHz to 60KHz
●The matrix master can switch every output channels to any HDMI inputs by push-in button, IR
remote control, RS-232 control, and Ethernet control
●Allows controlling local HDMI sources such as DVD and TiVo by attached IR extender from
remote receiver to matrix master
●Extends video signal up to 35m (115 feet) over single CAT.X at 1080p and likely longer with better
HDMI source device (such as PS3), better grade HDMI display (such as Sony X-series HDTV), and
better quality solid CAT6 cable
●Easy installation with rack-mounting and wall-mounting designs for master and receiver
respectively
●Fast response time –2~5 seconds for channel switch
PACKAGE CONTENTS
●1x AV-GM07J3-S1 ●1x UC AC Power cord
●1x IR receiver ●1x IR blaster*
●1x Rack-mounting ear set ●1x IR Remote control*
●1x Installation software CD ●1x User Manual

2
SPECIFICATIONS
Model Name
AV-GM07J3-S1
Technical
AV-GM07J3-S1
MA-5288RX
Role of usage
True 16x16 matrix switcher
Transmitter [TX]
Receiver [RX]
HDMI compliance
HDMI Deep Color & full 3D
HDCP compliance
Yes
Video bandwidth
Single-link 225MHz [6.75Gbps]
Video support
480i / 480p / 720p / 1080i / 1080p60 36-bit color
Audio support
Surround sound (up to 7.1ch) or stereo digital audio
HDMI over CAT5
transmission range
Full HD (1080p): 35m (115ft) [CAT.X]
HD (720p/1080i): 50m (165ft) [CAT.X]
HDMI equalization
N/A
8-level digital rotary control
Input TMDS signal
1.2 Volts [peak-to-peak]
Input DDC signal
5 Volts [peak-to-peak, TTL]
ESD protection
[1] Human body model —±19kV [air-gap discharge] & ±12kV [contact
discharge]
[2] Core chipset —±8kV
PCB stack-up
4-layer board [impedance control —differential 100Ω; single 50Ω]
Input
16x HDMI / 1x RS-232 / 1x Ethernet
1x IR socket for IR receiver
1x RJ-45 /
1x IR socket for IR receiver
Output
16x RJ-45 /
17x IR socket for IR blaster
1x HDMI /
1x IR socket for IR blaster
HDMI Input selection
Push-in button / IR remote control /
RS-232 control / Ethernet control
IR remote control
HDMI source control
Controllable via IR pass-through from IR receiver at RX to IR blaster at TX
IR remote control
Electro-optical characteristics: = 25° / Carrier frequency: 20-60kHz
HDMI connector
Type A [19-pin female]
RJ-45 connector
WE/SS 8P8C
RS-232 connector
DE-9 [9-pin D-sub female]
3.5mm connector
Earphone jack for IR blaster
[All IR Out] IR control on all source
devices
[IR1~IR16]IR control on individual
source device
Earphone jack for IR blaster
[IR] IR control on individual display
device
Earphone jack for IR receiver
* Additional IR remote controllers and IR blasters can be purchased as optional accessories to
control the HDMI sources located separately.

3
Earphone jack for IR receiver
[System IR] Receives IR commands
from remote control
[IR] Receives IR commands from
remote control
Mechanical
AV-GM07J3-S1
MA-5288RX
Enclosure
Metal case
Dimensions
(L x W x H)
Model
TBA
TBA
Package
TBA
Carton
TBA
Weight
Model
TBA
TBA
Package
TBA
Fixedness
3RU rack-mount with ears
Wall hanging holes
Wall-mount with screws
Power supply
AC Power 100-240V
5V 2A DC
Power consumption
1.5 Watt [max]
Operation
temperature
0~40°C [32~104°F]
Storage temperature
-20~60°C [-4~140°F]
Relative humidity
20~90% RH [no condensation]

4
PANEL DESCRIPTIONS
Transmitting unit ►AV-GM07J3-S1-TX
Front Panel
1. Power Switch: Power ON/OFF switch
2. Source Status: Input source indicator LED
3. Output 7-segment LED: LED display for output ports
4. IR SENSOR: IR sensor for receiving the IR commands from IR remote
5. Input 7-segment LED: LED display for input channels
6. Output Push Button: Front panel push buttons used to select the number of display
channel
7. Enter Button: Trigger the IN/OUT mapping setting
8. Input Push Button: Front panel push buttons used to select the number of input source
Rear Panel
9. INPUT 1-16: HDMI inputs
10.IR Blaster 1-16: Infrared 3.5mm socket for plugging in the extension cable of IR blaster
11.Output Port 1-16: RJ-45 outputs for each output channel
12.RS-232: RS-232 control port

5
13.Ethernet: Ethernet control port
14.All IR Output: 3.5mm IR blaster socket for HDMI source control on all 16 inputs
15.System IR Receiver: Ext. IR receiver
16.AC Power: 100-240V
Receiving unit ►MA-5288RX
Front Panel
Rear Panel
1. Signal Level: Adjust the 8-level equalization control to the received HDMI signals. The HDMI
signal level varies from strongest (0) to weakest (7) for respective transmission length from
longest possible range to short distance. Please adjust the signal level from strongest to weakest
and stop turning the rotary switch whenever the audio/video is playing normally. Inappropriate
signal level setting may cause overpowering issue that would shorten the product life
significantly!
2. HDMI Output: Connect to HDTV with a HDMI cable
3. IR RECEIVER: Plug in IR receiver
4. IR Blaster: Plug in IR blaster
5. +5V DC: 5V DC power jack
6. HDMI Signal IN: Plug in a Cat.X cable

6
IR PASS-THROUGH
IR Extenders
IR Blaster
IR Receiver
IR Sockets
AV-GM07J3-S1
All IR Out: The default location for IR blaster to transmit all IR command signals received from any
of the four remote receivers to all of the HDMI sources.
IR BLASTER 1-16: IR blaster connected here can only transmit IR command signals from the remote
receivers that are setting at respective input channel from 1 to 16.
System IR: Receives IR commands from remote control
MA-5288RX
IR BLASTER: IR control on individual display device
IR RECEIVER: IR receiver connected here can receive all IR command signals from the IR remote
controls of AV-GM07J3-S1 and all other HDMI source devices.
Definition of IR Earphone Jack
IR Blaster
IR Receiver
Incorrect placement of IR Blaster and Receiver may result in the failure of the IR
extenders. Please check carefully before plugging in the IR extender to the
respective IR sockets. Warranty will not cover the damage.
CAUTION!

7
HARDWARE INSTALLATION
AV-GM07J3-S1 as master
1. Connect all sources to HDMI Inputs on the 16x16 HDMI over CAT.X matrix master AV-GM07J3-S1.
2. Connect each CAT.X output port on the AV-GM07J3-S1 to respective CAT.X input on the remote
receiver MA-5288RX.
3. Connect IR blaster to the AV-GM07J3-S1 and direct the IR blaster to point towards the built-in IR
receiver of the HDMI source devices.
4. Connect the +12V 5A DC power supply to the AV-GM07J3-S1.
5. Power on all HDMI sources.
MA-5288RX as receiver
1. Connect each HDMI output to HDMI displays.
2. Connect the CAT.X input on the MA-5288RX to the CAT.X output port on the AV-GM07J3-S1.
3. Connect IR receiver and place the IR receiver at the appropriate position that can receive the IR
signals sent from the users.
4. Dial the 8-level rotary control switch to adjust the HDMI signal level until the picture and sound
are clear. It is recommended to dial from weakest to strongest to find the optimal visual
experience
You can buy any IR extension cables in the market that are compatible to the definition of
the IR sockets for the matrix if necessary for replacement use. However, IR cables longer
than 2m (6-ft) may not work.

8
CONNECTION DIAGRAM

9
OPERATION APPROACH
Method A: Push-in Button
1. IN/OUT MAP
1) Use the “ ”or “ “ output push button to select the number of display
2) Use the “ ”or “ “ input push button to select the number of input source
“”: change selected input/output port in ascending order
“” : change selected input/output port in descending order
3) After selecting the desired input/output port, please push the enter button to let the setting be
effective
Method B: IR Remote Control
Button
Function
ON
Power on the matrix switcher
OFF
Standby mode
PRESET
Preset mapping mode
SAVE
Save current mapping mode
Number buttons 1-9
Select a number
+10
Plus 10 for number key
To
Transfer key
TAKE
Trigger the previous setting
SWITCH
Begin input and output
selection
DEFAULT EDID
Begin default EDID selection
LEARN
Reserved
ALL
Select all inputs or outputs
CLEAR
Clear the previous IR operation
procedure
MUTE
Turn off output’s video and

10
audio
STATUS
Preset output status
F1
Reserved
F2
Reserved
F3
Reserved
F4
Reserved
Operation
Procedure
7-Segment
LED
IN/OUT Switch
Switch + number(output) + To + number(input) +
Take
Ex1: Input 3
To Output 4
1.Press “SWITCH” button
--;--
2.Press number key “4” to select Output
04;--
3.Press “To” button
04;
4.Press number key “3” to select Input
04;03
5.Press “TAKE” button
04;03
Ex2: Input 13
To Output 14
1.Press “SWITCH” button
--;--
2.Press number key “+10” and then “4” to select
Output
14;--
3.Press “To” button
14;
4.Press number key “+10” and then “3” to select
Input
14;13
5.Press “TAKE” button
14;13
Switch + All(output) + To + number(input) + Take
Ex: Input 3
To Output All
1.Press “SWITCH” button
--;--
2.Press “ALL” to select All Output
All;--
3.Press “To” button
All;
4.Press number key “3” to select Input
All;03
5.Press “TAKE” button
Output Status
Switch + number(output) + To + Status + Take
Ex: Output 4
(Input 2)
1.Press “STATUS” button
--;--
2.Press “SWITCH” button
--;--
3.Press number key “4” to select Output
04;--
5.Press “TAKE” button
04;02
Learn Default EDID
Default EDID + number(1-8 default EDID) + To +
number(input) + Take
Ex: Default EDID 2
Input 3
1.Press “DEFAULT EDID” button
Ed;--
2.Press number key “2” to select default EDID
02;All
3.Press “To” button
02;--
4. Press number key “3” to select Input
02;03
5.Press “TAKE” button
Default EDID + number(1-8 default EDID) + Take
Ex: Default EDID 2
1.Press “DEFAULT EDID” button
Ed;--

11
Input All
2.Press number key “2” to select default EDID
02;All
3.Press “TAKE” button
Save Current Mapping
Save + number(1-8 storage site) + Take
Ex: Save current
mapping to 5
1.Press “SAVE” button
SA;VE
2.Press number key “5” to select the storage site
00;05
3.Press “TAKE” button
Preset Mapping
Preset + number(1-8 storage site) + Take
Ex: Preset saved
mapping from 5
1.Press “PRESET” button
Lo;Ad
2.Press number key “5” to select the storage
site
00;05
3.Press “TAKE” button
Mute Output
Switch + number(output) + To + Mute + Take
Ex: Mute Output 3
1.Press “SWITCH” button
--;--
2.Press number key “3” to select Output
03;--
3.Press “To” button
03;
4.Press “MUTE” button
03;00
5.Press “TAKE” button
03;00
Switch + All(output) + To + Mute + Take
Ex: Mute All Output
1.Press “SWITCH” button
--;--
2.Press “ALL” to select all output
All;--
3.Press “To” button
All;
4.Press “MUTE” button
All;00
5.Press “TAKE” button

12
Method C: Software Control through RS-232 port / Ethernet port
1. System Requirement
1) OS Information: MS WinXP/7
2) Baud rates: 9600
3) Software size: 3 MB
4) Minimum RAM requirement: 256 MB
1
Version Button for FW/ SW
8
EDID Button
2
RS-232 Button
9
Firmware Update Button
3
Ethernet Button
10
Network Button
4
COM Port Selection
11
Mapping Button
5
Connect/Disconnect Status
12
Default Reset Button
6
Connect Button
13
In/Out Switch Button
7
Power On/Off Button
14
Mute Output Button
2. Step by step for connecting matrix and controller
Step1: Use RS-232 cable to connect the RS-232 port on matrix and PC
Step2: Open the software and then choose the correct com port
Step3: Click connection button “ ”

13
Step4: Make sure the connection status is on connected status “ ”
3. FW/SW Version Button
Click “ ” button to show version information
4. RS-232 Button
1) Click “”button to switch to RS-232 function.
2) If RS-232 is connected, the button will show the sign image to let you know.
5. Ethernet Button
1) Click “ ” button to switch to Ethernet function
2) If Ethernet is connected, the button will show the sign image to let you know.
6. COM Port Selection
Click “ ” button to select COM Port
7. Connection Status
1) Connected Status:
2) Connecting Status:
3) Disconnected Status:
8. Connect/Disconnect Button
Click this button “ ” to change connection status

14
9. Power On/Off Button
Click this button to power on/off
“ ” Power on status(Blue): Click this button to power off device(Standby Mode)
“ ” Power off status(Red): Click this button to power on device
10. EDID Button
1) Learn EDID from Default
a) Select Default EDID(1-8 Default EDID)
b) Select Input
c) Click “Learn” button to learn default EDID
2) Load EDID File to Input

15
a) Select Input
b) Click “Load” button to select the EDID file
3) Create EDID File
a) Click “Create”button to create EDID file
b) Select the EDID content
c) Click “Save EDID on Computer” to save the generated EDID as a file
4) View EDID content
a) Select Input, HDMI output, or From File
b) Click “View” button to read the EDID and analysis

16
c) Click “Save As”to save the read EDID as a file on computer
11.Firmware Update Button
1) Make sure RS-232 is connecting and the connecting status is “ ”
2) Click ”FIRMWARE UPDATE” Button and then will be a pop-up windows
3) F/W Update for Control Board
Step1: Click “Load File” to select the firmware file which you want to update

17
Step2: Power OFF the AV-GM07J3-S1
Step3: Power ON the AV-GM07J3-S1
Step4: Click “Start” button and the firmware will start writing
4) F/W Update for Input and Output Card
Step1: Click “Load File” to select the firmware file which you want to update
Step2: Click “Start” button and the firmware will start writing

18
12.Network Button
Step1: Make sure the connection status is on connected status “ ”
Step2: Connect matrix to network through IP control port
Step3: Click “NETWORK” Button and then will be a pop-up windows
Step4: Click “Read From Device” to read the device IP address
Step5: Select “Ethernet” button and then will be a pop-up windows
Step6: Key in the device IP address to the pop-up windows and click OK
Step7: Click the Connect Button “ ”to connect then you start control by Ethernet
*Remark: Switch controlling by clicking the shortcut button
RS-232 Button:
Click the button and then click “Connect Button” to start
Ethernet Button:
Click the button and then click “Connect Button” to start