Sinoboom TB800 Plus User manual

TB24 Plus/TB800 Plus
TB26J Plus/TB870J Plus
Operation
Manual
Part No.505064100002
Rev: A
Apr 2021
GTJZ
0608E (2132E)
GTJZ
0808E (2732E)
GTJZ
0808E (2732E)
GTJZ
0808E (2732E)
长沙市宁乡高新技术产业园区金洲大道东
128 号
0731-87116111 hr@sinoboom . c om . cn ww w .sinoboom . c om . cn
Al w ays F or B e t t er A cc ess Solution s
我们一直在追求新的高 度
尺寸 ：
210×285mm
20mm
20mm
产品说明书
PRODU C T MAN U AL

Operating, servicing and maintaining this vehicle or
equipment can expose you to chemicals including engine
exhaust, carbon monoxide, phthalates, and lead, which
are known to the State of California to cause cancer and
birth defects or other reproductive harm. To minimize
exposure, avoid breathing exhaust, do not idle the engine
except as necessary, service your vehicle or equipment in
a well-ventilated area and wear gloves or wash your
hands frequently when servicing. For more information
go to: www.P65warnings.ca.gov.

Please contact us:
Website : www.sinoboom.com
E-mail : [email protected]
Sales Tel : [phone]
Service Tel : [phone]
Address : No.128, East Jinzhou Avenue, Ningxiang High-tech Industrial Park, Changsha,
Hunan, China
Zip Code : 410600
Copyright © Hunan Sinoboom Intelligent Equipment Co., Ltd. All Rights Reserved
The final interpretation right of this manual belongs to Hunan Sinoboom Intelligent Equipment Co., Ltd.
Manual revision history：
REV DATE DESCRIPTION REMARK
AApr. 2021 Original issue

APPLICATION
Use the following table to identify the specific serial number for
models included in this manual. Check the model of your machine before
consulting the manual, and then use the correct manual according to the
serial number of the model. See the nameplate on your machine to
identify the model and serial number.(See Decals/Nameplate Inspection
of the Operation Manual for details.)
Model
Trade Identification
Serial No.
Metric Imperial
TB24 Plus TB24 Plus TB800 Plus From 0505100100 to present
TB26J Plus TB26J Plus TB870J Plus From 0506400100 to present
NOTE:
•Product model is applied in product nameplate for distinction of products of different main
parameters.
•Product trade identification is applied in marketing and machine decals for distinction of products of
different main parameters, and can be classified as metric type and imperial type: The metric type of
trade identification is applicable to machines for countries/regions using metric system or as
specially required by customers; The imperial type of trade identification is applicable to the
machines for countries/regions using imperial system or as specially required by customers.

This Page Intentionally Left Blank

STATEMENTS
Hunan Sinoboom Intelligent Equipment Co., Ltd. (Hereinafter referred to as Sinoboom) will upload the
latest product manual information to the website www. sinoboom. com as soon as possible. However,
due to continuous product improvement, the information in this manual is subject to change without prior
notice.
This manual covers the basic parts information of one or more products. Therefore, please use this
manual according to your needs. If you find problems in the manual or have suggestions for improve-
ment, feel free to share your feedback with Sinoboom, and we will address these issues as soon as
possible.
Feel free to consult and download the Operation Manual,Maintenance Manual and Parts Manual of the
products you need online at www.sinoboom.com.
Hunan Sinoboom Intelligent Equipment Co., Ltd. retains the right of final interpretation of the manual.

This Page Intentionally Left Blank

TB24 Plus&26J Plus Operation Manual i© Apr 2021
TABLE OF CONTENTS
Introduction ............................. iii
1 Machine Specifications ........ 1-1
2 Machine Components .......... 2-1
3 Safety............................... 3-1
Safety Definitions . . . . . . . . .. . . . . . . . . . . . 3-1
Reporting Accidents. . . . . . . . . . . . . . . . . . . 3-1
Electrocution Hazards. . . . . . . . . . . . . . . . . 3-1
Tipping Hazards and Rated Load . . . . . 3-2
Jobsite Hazards . . . . . . . . . . . . . . . . . .. . . . . 3-4
Unsafe Operation Hazards. . . . . . . . . . . . 3-6
FallHazards...........................3-7
Collision Hazards . . . . . . . . . . . . . . . . . . . . . 3-7
Crush Hazards . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Explosion and Fire Hazards. . . . . . . . . . . 3-9
Damaged Machine Hazards . . . . . . . . . . 3-9
Bodily Injury Hazards . . . . . . . . . . . . . . . . . 3-9
Battery Hazards . . . . . . . . . . . . . . . . . .. . . . . 3-9
Hydraulic Hazards . . . . . . . . . . . . . . . . . . . 3-11
Welding and Polishing Requirements 3-11
After Using the Machine. . . . . . . . . . . . . . 3-11
4 Jobsite Inspection............... 4-1
5 Pre-operation Inspection ...... 5-1
Tips for Conducting a Pre-operation
Inspection.............................5-1
Conducting a Pre-operation
Inspection.............................5-2
Inspecting Parts . . . . . . . . . . . . . . . . . .. . . . . 5-2
Inspecting Entire Machine . . . . . . . . . . . . 5-2
Inspect Hydraulic Oil Level. . . . . . . . . . . . 5-2
Inpsecting Fuel Level . . . . . . . . . . . . . . . . . 5-3
Inspecting Engine Oil Level . . . . . . . . . . . 5-4
Inspecting Coolant Level （water-
cooled engine）.......................5-5
Inspecting the Battery . . . . . . . . . . . . . . . . . 5-6
6 Pre-operation Function Test .. 6-1
Preparing for a Pre-operation
Function Test. . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Testing the Ground Controller . . . . . . . . . 6-1
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Testing the horn. . . . . . . . . . . . . . . .. . . . . 6-4
Testing the engine start switch. . . . . . 6-4
Testing the emergency stop button . 6-4
Testing the Ground/Platform select
switch...............................6-5
Testing the enable switch . . . . . . . . . . . 6-5
Testing the main boom up/down
switch...............................6-5
Testing the main boom telescope
switch...............................6-5
Testing the turntable rotate switch . . 6-5
Testing the platform level switch . . . . 6-5
Testing the platform rotate switch. . . 6-6
Testing the jib up/down switch-
TB26J Plus only . . . . . . . . . . . . . . . . . . . . 6-6
Testing the jib rotate switch-TB26J
Plus (if equipped) . . . . . . . . . . . . . . . . . . . 6-6
Testing the emergency power
switch...............................6-6
Testing the engine high/low speed
select switch . . . . . . . . . . . . . . . . . . . . . . . . 6-6
Testing the buzzer . . . . . . . . . . . . . . . . . . 6-7
Testing the engine glow plug
switch(if equipped). . . . . . . . . . . . . . . . . . 6-7
Testing the Platform Controller . . . . . . . . 6-7
Testing the Drive Speed. . . . . . . . . . . . . .6-13
Testing the Emergency Lowering
Function..............................6-14
Testing the Tilt Protection System. . . .6-14
Testing the Envelope Restriction . . . . .6-15

© Apr 2021 ii TB24 Plus&26J Plus Operation Manual
Testing the Weighing System . . . .. . . .6-15
7 Operating the Machine ......... 7-1
Stability................................7-1
Emergency Stop . . . . . . . . . . . . . . . . . . . . . . 7-3
Emergency Lowering . . . . . . . . . . . . . . . . . 7-4
Emergency Operating. . . . . . . . . . . . . . . . . 7-4
Emergency Towing/Dragging . . . . . . . . . 7-4
Operation from Ground . . . . . . . . . . . . . . . 7-5
Operation from Platform . . . . . . . . . . . . . . 7-6
Driving on a Slope. . . . . . . . . . . . . . . . . . . . . 7-7
8 Transporting and Lifting the
Machine........................... 8-1
Lifting the Machine with a Crane . . . . . . 8-2
Transporting the Machine . . . . . . . . . . . . . 8-3
9 Maintenance ...................... 9-1
Conducting a Pre-delivery Inspection . 9-1
Following a Maintenance Schedule . . . 9-2
Completing a Repair & Inspection
Report.................................9-2
10 Decals/Nameplates
Inspection ....................... 10-1
Decals/Nameplates-GB . . . . . . . . . . .10-2
Decals/Nameplates (CE-Metric) . . .10-5
Decals/Nameplates (CE-Imperial) .10-8
Decals/Nameplates (ANSI) . . . . . . .10-11
Decals/Nameplates (CSA)-TB24
Plus.............................. 10-14
Appendix 1: Symbols and
Description.......................A-1
Appendix 2: Prepare the Work
Record Before Delivery ....... A-3
Appendix 3: Repair & Inspection
Report .............................A-5

TB24 Plus&26J Plus Operation Manual iii © Apr 2021
INTRODUCTION
Thank you for choosing and using the machinery of
Hunan Sinoboom Intelligent Equipment Co., Ltd. Al-
ways read, understand and become familiar with the
operation requirements of the machine and its associ-
ated safety procedures before operating, maintaining
and repairing the machine. Operating the machine with-
out becoming familiar with its specific operation require-
ments and safety procedures poses serious risks.
Operators who follow safety rules and operate the ma-
chine carefully and effectively will prevent personal in-
jury, property loss and accidents.
Use this machine only to transport tools to work loca-
tions and for performing tasks on the work platform. Op-
erators must be competent and must obtain training to
carefully use the machine and follow safety procedures.
Only trained and authorized personnel may operate the
machine.
This manual guides the operator in operating and using
the machine. The operator is responsible for reading,
understanding and implementing the operation and
safety procedures in this manual and for following the
manufacturer’s instructions before beginning any work.
Read, understand and follow all safety rules and oper-
ating instructions. The operator must also consider the
machine’s uses and limitations and the conditions at
the jobsite before using this machine. Strictly following
all safety requirements in this manual is critical.
Consider this manual a part of the machine, along with
Maintenance Manual and Parts Manual, and always
keep the manuals with the machine. The owner or ad-
ministrator of the machine shall offer all manuals and
other necessary information provided by the machine
manufacturer regarding the daily inspection and main-
tenance to each of the renters. If the machine is sold,
the owner or administrator must pass along the man-
uals and other necessary information to the purchaser.
The owner or administrator of the machine shall also
provide the manufacturer’s maintenance information to
the person responsible for maintaining the machine.
If you have any questions, contact Hunan Sinoboom In-
telligent Equipment Co., Ltd..

© Apr 2021 iv TB24 Plus&26J Plus Operation Manual
This Page Intentionally Left Blank

TB24 Plus&26J Plus Operation Manual 1-1 © Apr 2021
1MACHINE SPECIFICATIONS
Table 1-1 TB24 Plus specifications
MEASURE TB24 Plus (METRIC) TB800 Plus (IMPERIAL)
DIMENSION
Max platform height 24.4m 80ft 0.6in
Max working height 26.4m 86ft 7in
Max horizontal reach (restricted/
unrestricted) 18.43 m/20.74 m 60ft 5.6in / 68ft 0.5in
Overall length(stowed) 11.55m 37ft 11in
Overall width(stowed) 2.49m 8ft 2in
Overall height (stowed) 2.88m 9ft 5in
Wheelbase 3m 9ft 10in
Ground clearance 0.46m 1ft 6in
Tire size (spec / type)
Options
385/65-22.5 (foam-filled)
385/65-24/10.00 (solid)
Platform dimension (L×W×H)
Options
1.45×0.85×1.1 m
1.83×0.85×1.1 m
2.44×0.91×1.1 m
Options
4ft 9in×2ft 9in×3ft 7in
6ft×2ft 9in×3ft 7in
8ft×3ft×3ft 7in
PERFORMANCE
Rated platform capacity (restricted/
unrestricted) 454kg/300kg 1000 lb/661 lb
Max number of occupants
(restricted/unrestricted) 3P/2P
Turntable rotation / continuous 360°/continuous
Platform rotation 160°
Max drive speed (stowed) 4.8km/h 3mph
Max drive speed (raised) 1.1km/h 0.68mph
Drive mode (drive×steer) 4WD×2WS
Gradeability 45%/24°
Turntable tailswing 0.32m 1ft
Max allowable inclination 5°
Turning radius (inside) 4.62m 15ft 2in
Turning radius (outside) 6.91m 22ft 8in
Max allowable side force 600N/400N 135 lbf/90 lbf

© Apr 2021 1-2 TB24 Plus&26J Plus Operation Manual
MACHINE SPECIFICATIONS
Table 1-1 TB24 Plus specifications (continued)
MEASURE TB24 Plus (METRIC) TB800 Plus (IMPERIAL)
Max operating noise level 79dB
IP grade IP65
POWER
Engine (rated power, rated rpm)
54kw/2400rpm/QSF2.8t3TC72/Cummins/China 3
55.4kw/2600rpm/TD2.9 L4/Deutz/Euro 5
55.4KW/2600rpm/TD2.9 L4/Deutz/US Stage 4
55.4kw/2400rpm/TD2011 L04i/Deutz/tier 3
Hydraulic tank capacity 190 L 41.8gal (UK)/50.2gal (US)
Fuel tank capacity 160L 35.2gal (UK)/42.3gal (US)
Hydraulic system pressure 28MPa 4061Psi
Battery (number×voltage, capacity) 2×12V, 110Ah
System voltage 12 VDC
Control voltage 12 VDC
GROUND BEARING DATA
Max tire load 9620kg 21208 lb
Pressure against ground 730kpa 105.9Psi
ENVIRONMENT
Max allowable wind speed 12.5 m/s 28 mph
Max allowable altitude 1000 m 3280ft
Allowable ambient temperature
(lead-acid battery)
-10℃～40℃14℉～104℉
Allowable ambient temperature (-
lithium battery)
-20℃～40℃-4℉～104℉
Max allowable RH 90%
Storage environment
Stored at -20℃to 50℃(-4℉to 122℉) in a well-ventilated environment with
90% relative humidity (20℃[68℉]), and away from rain, sun, corrosive
gas,inflammables and explosives.
WEIGHT
Gross weight (unladen) 16530kg 36442 lb
Note：
a) The working height adds 2m(6ft7in) of human height to platform height。
b) The ground bearing data is approximate value, not factoring the different options,thus it serves only in adequately safe
conditions
c) In different areas, hydraulic oil, engine oil, coolant, fuel and lubrication should be added in accordance with the
environmental temperature.
d) In cold weather, auxiliary devices are needed to start the machines.
e) Rated platform capcity represents the rated load of the platform, including the loads of persons, materials, tools, platform
accessories and other objects borne by the platform.

MACHINE SPECIFICATIONS
TB24 Plus&26J Plus Operation Manual 1-3 © Apr 2021
Table 1-2 TB26J Plus specifications
MEASURE TB26J Plus (METRIC) TB870J Plus (IMPERIAL)
DIMENSION
Max platform height 26.3 m 86ft 3in
Max working height 28.3 m 92ft 10in
Max horizontal reach (restricted/
unrestricted) 17.91 m/20 m 58ft 9in/65ft 7in
Overall length(stowed) 12.5 m 41ft
Overall width(stowed) 2.49 m 8ft 2in
Overall height (stowed) 2.88 m 9ft 5in
Wheelbase 3 m 9ft 10in
Ground clearance 0.46m 1ft 6in
Tire size (spec / type)
Options
385/65-22.5 (foam-filled)
385/65-24/10.00 (solid)
Platform dimension (L×W×H)
Options
1.45×0.85×1.1 m
1.83×0.85×1.1 m
2.44×0.91×1.1 m
Options
4ft 9in×2ft 9in×3ft 7in
6ft×2ft 9in×3ft 7in
8ft×3ft×3ft 7in
PERFORMANCE
Rated platform capacity (restricted/
unrestricted) 454kg/300kg 1000 lb/661 lb
Max number of occupants
(restricted/unrestricted) 3P/2P
Turntable rotation / continuous 360°/continuous
Platform rotation 160°
Max drive speed (stowed) 4.8km/h 3 mph
Max drive speed (raised) 1.1 km/h 0.68 mph
Drive mode (drive×steer) 4WD×2WS
Gradeability 45%/24°
Turntable tailswing 0.32 m 1ft
Max allowable inclination 5°
Turning radius (inside) 4.62 m 15ft 2in
Turning radius (outside) 6.91 m 22ft 8in
Max allowable side force 600N/400N 135 lbf/90 lbf
Max operating noise level 79dB
IP grade IP65
POWER

© Apr 2021 1-4 TB24 Plus&26J Plus Operation Manual
MACHINE SPECIFICATIONS
Table 1-2 TB26J Plus specifications (continued)
MEASURE TB26J Plus (METRIC) TB870J Plus (IMPERIAL)
Engine (rated power, rated rpm)
54kw/2400rpm/QSF2.8t3TC72/Cummins/China 3
55.4kw/2600rpm/TD2.9 L4/Deutz/Euro 5
55.4KW/2600rpm/TD2.9 L4/Deutz/US Stage 4
55.4kw/2400rpm/TD2011 L04i/Deutz/tier 3
Hydraulic tank capacity 190 L 41.8gal (UK)/50.2gal (US)
Fuel tank capacity 160 L 35.2 gal(UK)/42.3 gal(US)
Hydraulic system pressure 28 MPa 4061 Psi
Battery (number×voltage, capacity) 2×12V, 110Ah
System voltage 12 VDC
Control voltage 12 VDC
GROUND BEARING DATA
Max tire load 9620kg 21208 lb
Pressure against ground 730kpa 105.9 Psi
ENVIRONMENT
Max allowable wind speed 12.5 m/s 28 mph
Max allowable altitude 1000 m 3280ft
Allowable ambient temperature
(lead-acid battery)
-10℃～40℃14℉～104℉
Allowable ambient temperature (-
lithium battery)
-20℃～40℃-4℉～104℉
Max allowable RH 90%
Storage environment
Stored at -20℃to 50℃(-4℉to 122℉) in a well-ventilated environment with
90% relative humidity (20℃[68℉]), and away from rain, sun, corrosive
gas,inflammables and explosives.
WEIGHT
Gross weight (unladen) 17000kg 37479lb
Note：
a) The working height adds 2m(6ft7in) of human height to platform height。
b) The ground bearing data is approximate value, not factoring the different options,thus it serves only in adequately safe
conditions
c) In different areas, hydraulic oil, engine oil, coolant, fuel and lubrication should be added in accordance with the
environmental temperature.
d) In cold weather, auxiliary devices are needed to start the machines.
e) Rated platform capcity represents the rated load of the platform, including the loads of persons, materials, tools, platform
accessories and other objects borne by the platform.

MACHINE SPECIFICATIONS
TB24 Plus&26J Plus Operation Manual 1-5 © Apr 2021
TB24 Plus range of motion
Restricted Unrestricted

© Apr 2021 1-6 TB24 Plus&26J Plus Operation Manual
MACHINE SPECIFICATIONS
TB26J Plus range of motion
Restricted Unrestricted

TB24 Plus&26J Plus Operation Manual 2-1 © Apr 2021
2MACHINE COMPONENTS
Figure 2-1
32
31
30
2827
29
1
2
3
4567
8
9
10
1112
13
14
17
15
24
21 22 23
16
1918
26
25
20
33
35
36
34
37

© Apr 2021 2-2 TB24 Plus&26J Plus Operation Manual
MACHINE COMPONENTS
Table 2-1
1. Platform 14. Hydraulic tank 27. AC power receptacle (option)
2. Jib lift cylinder 15. Ground controller 28. Manual storage container (option)
3. Jib boom 16. Oscillate cylinder 29. Footswitch
4. Slave cylinder 17. Front wheel 30. Plataform controller
5. 2nd telescopic boom 18. Steer linkage 31. Work light (option)
6. 1st telestcopic boom 19. Steer cylinder 32. Limit device (option)
7. Base boom 20. Power plug 33. Turntable cover, LH
8. Cable track 21. Rear wheel 34. Battery
9. Main lift cylinder 22. Drive reducer 35. Slewing bearing
10. Master cylinder 23. Drive motor 36. Engine
11. Flash beacon 24. Chassis 37. Power disconnect switch
12. Counterweight 25. Turntable
13. Fuel tank 26. Turntable cover, RH
Machine positions
Stowed position：
Boom lowers and retracts in place.
Non-operating position：
Boom rises at an angle not exceeding 15°, and extends
not exceeding 1.2m.
Operating/raised position：
Boom rises at an angle exceeding 15°, or extends
beyond 1.2m.