Sinoboom TB18E Plus User manual

TB18E Plus/TB590E Plus
TB20EJ Plus/TB660EJ Plus
TB20E Plus/TB680E Plus
TB22EJ Plus/TB740EJ Plus
Operation
Manual
Part No.514002100002
Rev: A
Oct 2021
GTJZ
0608E (2132E)
GTJZ
0808E (2732E)
GTJZ
0808E (2732E)
GTJZ
0808E (2732E)
长沙市宁乡高新技术产业园区金洲大道东
128 号
0731-87116111 hr@sinoboom . c om . cn ww w .sinoboom . c om . cn
Al w ays F or B e t t er A cc ess Solution s
我们一直在追求新的高 度
尺寸 ：
210×285mm
20mm
20mm
产品说明书
PRODU C T MAN U AL

Operating, servicing and maintaining this vehicle or
equipment can expose you to chemicals including engine
exhaust, carbon monoxide, phthalates, and lead, which
are known to the State of California to cause cancer and
birth defects or other reproductive harm. To minimize
exposure, avoid breathing exhaust, do not idle the engine
except as necessary, service your vehicle or equipment in
a well-ventilated area and wear gloves or wash your
hands frequently when servicing. For more information
go to: www.P65warnings.ca.gov.

Please contact us:
Website : www.sinoboom.com
E-mail : [email protected]
Sales Tel : [phone]
Service Tel : [phone]
Address : No.128, East Jinzhou Avenue, Ningxiang High-tech Industrial Park, Changsha,
Hunan, China
Zip Code : 410600
Copyright © Hunan Sinoboom Intelligent Equipment Co., Ltd. All Rights Reserved
The final interpretation right of this manual belongs to Hunan Sinoboom Intelligent Equipment Co., Ltd.
Manual revision history：
REV DATE DESCRIPTION REMARK
AOct. 2021 Original issue

APPLICATION
Use the following table to identify the specific serial number for
models included in this manual. Check the model of your machine before
consulting the manual, and then use the correct manual according to the
serial number of the model. See the nameplate on your machine to
identify the model and serial number.(See Decals/Nameplate Inspection
of the Operation Manual for details.)
Model
Trade Identification
Serial No.
Metric Imperial
TB18E Plus TB18E Plus TB590E Plus From 1400100100 to present
TB20EJ Plus TB20EJ Plus TB660EJ Plus From 1400200100 to present
TB20E Plus TB20E Plus TB680E Plus From 1401000100 to present
TB22EJ Plus TB22EJ Plus TB740EJ Plus From 1400600100 to present
NOTE:
•Product model is applied in product nameplate for distinction of products of different main
parameters.
•Product trade identification is applied in marketing and machine decals for distinction of products of
different main parameters, and can be classified as metric type and imperial type: The metric type of
trade identification is applicable to machines for countries/regions using metric system or as
specially required by customers; The imperial type of trade identification is applicable to the
machines for countries/regions using imperial system or as specially required by customers.

This Page Intentionally Left Blank

STATEMENTS
Hunan Sinoboom Intelligent Equipment Co., Ltd. (Hereinafter referred to as Sinoboom) will upload the
latest product manual information to the website www. sinoboom. com as soon as possible. However,
due to continuous product improvement, the information in this manual is subject to change without prior
notice.
This manual covers the basic parts information of one or more products. Therefore, please use this
manual according to your needs. If you find problems in the manual or have suggestions for improve-
ment, feel free to share your feedback with Sinoboom, and we will address these issues as soon as
possible.
Feel free to consult and download the Operation Manual,Maintenance Manual and Parts Manual of the
products you need online at www.sinoboom.com.
Hunan Sinoboom Intelligent Equipment Co., Ltd. retains the right of final interpretation of the manual.

This Page Intentionally Left Blank

TB18E Plus&20EJ Plus&20E Plus&22EJ Plus Operation Manual i© Oct 2021
TABLE OF CONTENTS
Introduction ............................. iii
1 Machine Specifications ........ 1-1
2 Machine Components .......... 2-1
3 Safety............................... 3-1
Safety Definitions . . . . . . . . .. . . . . . . . . . . . 3-1
Reporting Accidents. . . . . . . . . . . . . . . . . . . 3-1
Electrocution Hazards. . . . . . . . . . . . . . . . . 3-2
Tipping Hazards and Rated Load . . . . . 3-2
Jobsite Hazards . . . . . . . . . . . . . . . . . .. . . . . 3-4
Unsafe Operation Hazards. . . . . . . . . . . . 3-6
FallHazards...........................3-7
Collision Hazards . . . . . . . . . . . . . . . . . . . . . 3-7
Crush Hazards . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Explosion and Fire Hazards. . . . . . . . . . . 3-9
Damaged Machine Hazards . . . . . . . . . . 3-9
Bodily Injury Hazards . . . . . . . . . . . . . . . . . 3-9
Battery Hazards . . . . . . . . . . . . . . . . . .. . . .3-10
Welding and Polishing Requirements 3-11
After Using the Machine. . . . . . . . . . . . . .3-12
4 Jobsite Inspection............... 4-1
5 Pre-operation Inspection ...... 5-1
Tips for Conducting a Pre-operation
Inspection.............................5-1
Conducting a Pre-operation
Inspection.............................5-2
Inspecting Parts . . . . . . . . . . . . . . . . . .. . . . . 5-2
Inspecting Entire Machine . . . . . . . . . . . . 5-2
Inspect Hydraulic Oil Level. . . . . . . . . . . . 5-2
Inspecting the Battery . . . . . . . . . . . . . . . . . 5-3
6 Pre-operation Function Test .. 6-1
Preparing for a Pre-operation
Function Test. . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Testing the Ground Controller . . . . . . . . . 6-1
Testing the Platform Controller . . . . . . . . 6-6
Testing the Drive Speed. . . . . . . . . . . . . .6-12
Testing the Emergency Lowering
Function..............................6-12
Testing the Tilt Protection System. . . .6-13
Testing the Envelope Restriction . . . . .6-13
Testing the Weighing System . . . .. . . .6-14
7 Operating the Machine ......... 7-1
Stability................................7-1
Emergency Stop . . . . . . . . . . . . . . . . . . . . . . 7-3
Emergency Lowering . . . . . . . . . . . . . . . . . 7-4
Emergency Operating. . . . . . . . . . . . . . . . . 7-4
Emergency Towing/Dragging . . . . . . . . . 7-4
Operation from Ground . . . . . . . . . . . . . . . 7-5
Operation from Platform . . . . . . . . . . . . . . 7-6
Driving on a Slope. . . . . . . . . . . . . . . . . . . . . 7-7
Charging the Battery . . . . . . . . . . . . . . . . . . 7-8
8 Transporting and Lifting the
Machine........................... 8-1
Lifting the Machine with a Crane . . . . . . 8-2
Transporting the Machine . . . . . . . . . . . . . 8-3
9 Maintenance ...................... 9-1
Conducting a Pre-delivery Inspection . 9-1
Following a Maintenance Schedule . . . 9-2
Completing a Repair & Inspection
Report.................................9-2
10 Decals/Nameplates
Inspection ....................... 10-1
Decals/Nameplates(GB). . . . . . . . . . .10-2
Decals/Nameplates(CE-Metric) . . .10-5
Decals/Nameplates(CE-Imperial) .10-8
Decals/Nameplates(CSA) . . . . .. . .10-11
Decals/Nameplates(ANSI). . . . . . . 10-14

© Oct 2021 ii TB18E Plus&20EJ Plus&20E Plus&22EJ Plus Operation Manual
Appendix 1: Symbols and
Description.......................A-1
Appendix 2: Prepare the Work
Record Before Delivery ....... A-3
Appendix 3: Repair & Inspection
Report .............................A-5

TB18E Plus&20EJ Plus&20E Plus&22EJ Plus Operation Manual iii © Oct 2021
INTRODUCTION
Thank you for choosing and using the machinery of
Hunan Sinoboom Intelligent Equipment Co., Ltd. Al-
ways read, understand and become familiar with the
operation requirements of the machine and its associ-
ated safety procedures before operating, maintaining
and repairing the machine. Operating the machine with-
out becoming familiar with its specific operation require-
ments and safety procedures poses serious risks.
Operators who follow safety rules and operate the ma-
chine carefully and effectively will prevent personal in-
jury, property loss and accidents.
Use this machine only to transport tools to work loca-
tions and for performing tasks on the work platform. Op-
erators must be competent and must obtain training to
carefully use the machine and follow safety procedures.
Only trained and authorized personnel may operate the
machine.
This manual guides the operator in operating and using
the machine. The operator is responsible for reading,
understanding and implementing the operation and
safety procedures in this manual and for following the
manufacturer’s instructions before beginning any work.
Read, understand and follow all safety rules and oper-
ating instructions. The operator must also consider the
machine’s uses and limitations and the conditions at
the jobsite before using this machine. Strictly following
all safety requirements in this manual is critical.
Consider this manual a part of the machine, along with
Maintenance Manual and Parts Manual, and always
keep the manuals with the machine. The owner or ad-
ministrator of the machine shall offer all manuals and
other necessary information provided by the machine
manufacturer regarding the daily inspection and main-
tenance to each of the renters. If the machine is sold,
the owner or administrator must pass along the man-
uals and other necessary information to the purchaser.
The owner or administrator of the machine shall also
provide the manufacturer’s maintenance information to
the person responsible for maintaining the machine.
If you have any questions, contact Hunan Sinoboom In-
telligent Equipment Co., Ltd..

© Oct 2021 iv TB18E Plus&20EJ Plus&20E Plus&22EJ Plus Operation Manual
This Page Intentionally Left Blank

TB18E Plus&20EJ Plus&20E Plus&22EJ Plus Operation Manual 1-1 © Oct 2021
1MACHINE SPECIFICATIONS
Table 1-1 TB18E Plus specifications
MEASURE TB18E Plus (METRIC) TB600E Plus (IMPERIAL)
DIMENSION
Max platform height 18.1 m 59ft 5in
Max working height 20.1 m 65ft 11in
Max horizontal reach (restricted/
unrestricted)
14.1 m/15.45 m 46 ft 3 in / 50 ft 8 in
Overall length(stowed) 8.93 m 29ft 4in
Overall width(stowed) 2.49 m 8ft 2in
Overall height (stowed) 2.77 m 9ft 1in
Wheelbase 2.49 m 8ft 2in
Ground clearance 0.39 m 1ft 3in
Tire size (spec / type)
Options
36×14-20（non-marking）
36×14-20（solid）
355/65D625（foam-filled）
Platform dimension (L×W×H)
Options
1.45×0.85×1.1 m
1.83×0.85×1.1 m
2.44×0.91×1.1 m
Options
4ft 9in×2ft 9in×3ft 7in
6ft×2ft 9in×3ft 7in
8ft×2ft 11in×3ft 7in
PERFORMANCE
Rated platform capacity (restricted/
unrestricted) 454 kg/300 kg 1000 lb / 661 lb
Max number of occupants
(restricted/unrestricted) 3/2
Turntable rotation/continuous 360 °/continuous
Platform rotation 160°
Max drive speed (stowed) 4.8km/h 3 mph
Max drive speed (raised) 1.1 km/h 0.68 mph
Drive mode (drive×steer) 4WD×2WS
Gradeability 35%/19°
Turntable tailswing 1.45 m 4ft 9in
Max allowable inclination 5°
Turning radius (inside) 2.4 m 7ft 10.5in
Turning radius (outside) 5.55 m 18ft 2.5in

© Oct 2021 1-2 TB18E Plus&20EJ Plus&20E Plus&22EJ Plus Operation Manual
MACHINE SPECIFICATIONS
Table 1-1 TB18E Plus specifications (continued)
MEASURE TB18E Plus (METRIC) TB600E Plus (IMPERIAL)
Max allowable side force(restricted/
unrestricted) 600 N/400 N 134 lbf/90 lbf
Max operating noise level 80 dB
IP grade IP65
POWER
Motor（Volts/kW）29 V DC,15 kW
Duplex gear pump displacement 16 ml/r + 4 ml/r
Hydraulic tank capacity 170 L 37.4gal（UK）/44.9gal（US）
Hydraulic system pressure 28MPa 4061 Psi
Battery (number×voltage, capacity) 2×24V, 480Ah（lead-acid battery）
2×24V, 528Ah（lithium battery）
Power system voltage 48 VDC
Control system voltage 12 VDC
Charger（input voltage/output
current）100～240 V AC,60 A
GROUND BEARING DATA
Max tire load 6740 kg 14859 lb
Pressure against ground 675 KPa 97.9 Psi
ENVIRONMENT
Max allowable wind speed 12.5 m/s 28 mph
Max allowable altitude 1000 m 3280 ft
Allowable ambient temperature
(lead-acid battery)
-10℃～40℃14℉～104℉
Allowable ambient temperature (-
lithium battery)
-20℃～40℃-4℉～104℉
Max allowable RH 90%
Storage environment
Stored at -20℃to 50℃(-4℉to 122℉) in a well-ventilated environment with
90% relative humidity (20℃[68℉]), and away from rain, sun, corrosive
gas,inflammables and explosives.。
WEIGHT
Gross weight (unladen) 11328 kg 24974 lb
Table 1-2 TB20EJ Plus specifications
MEASURE TB20EJ Plus (METRIC) TB660EJ Plus (IMPERIAL)
DIMENSION
Max platform height 20 m 65ft 7in

MACHINE SPECIFICATIONS
TB18E Plus&20EJ Plus&20E Plus&22EJ Plus Operation Manual 1-3 © Oct 2021
Table 1-2 TB20EJ Plus specifications (continued)
MEASURE TB20EJ Plus (METRIC) TB660EJ Plus (IMPERIAL)
Max working height 22 m 72ft 2in
Max horizontal reach (restricted/
unrestricted) 13.85 m / 15.4 m 45 ft 5 in/50 ft 6 in
Overall length(stowed) 9.99 m 32ft 9in
Overall width(stowed) 2.49 m 8ft 2in
Overall height (stowed) 2.79 m 9ft 2in
Wheelbase 2.49 m 8ft 2in
Ground clearance 0.39 m 1ft 3in
Tire size (spec / type)
Options
36×14-20（non-marking）
36×14-20（solid）
355/65D625（foam-filled）
Platform dimension (L×W×H)
Options
1.45×0.85×1.1 m
1.83×0.85×1.1 m
2.44×0.91×1.1 m
Options
4ft 9in×2ft 9in×3ft 7in
6ft×2ft 9in×3ft 7in
8ft×2ft 11in×3ft 7in
PERFORMANCE
Rated platform capacity (restricted/
unrestricted) 454 kg/300 kg 1000 lb / 661 lb
Max number of occupants
(restricted/unrestricted) 3/2
Turntable rotation/continuous 360 °/continuous
Platform rotation 160°
Max drive speed (stowed) 4.8km/h 3 mph
Max drive speed (raised) 1.1 km/h 0.68 mph
Drive mode (drive×steer) 4WD×2WS
Gradeability 35%/19°
Turntable tailswing 1.45 m 4ft 9in
Max allowable inclination 5°
Turning radius (inside) 2.4 m 7ft 10.5in
Turning radius (outside) 5.55 m 18ft 2.5in
Max allowable side force(restricted/
unrestricted) 600 N/400 N 134 lbf/90 lbf
Max operating noise level 80 dB
IP grade IP65
POWER
Motor（Volts/kW）29 V DC,15 kW

© Oct 2021 1-4 TB18E Plus&20EJ Plus&20E Plus&22EJ Plus Operation Manual
MACHINE SPECIFICATIONS
Table 1-2 TB20EJ Plus specifications (continued)
MEASURE TB20EJ Plus (METRIC) TB660EJ Plus (IMPERIAL)
Duplex gear pump displacement 16 ml/r + 4 ml/r
Hydraulic tank capacity 170 L 37.4gal（UK）/44.9gal（US）
Hydraulic system pressure 28MPa 4061 Psi
Battery (number×voltage, capacity) 2×24V, 480Ah（lead-acid battery）
2×24V, 528Ah（lithium battery）
Power system voltage 48 VDC
Control system voltage 12 VDC
Charger（input voltage/output
current）100～240 V AC,60 A
GROUND BEARING DATA
Max tire load 6740 kg 14859 lb
Pressure against ground 675 KPa 97.9 Psi
ENVIRONMENT
Max allowable wind speed 12.5 m/s 28 mph
Max allowable altitude 1000 m 3280 ft
Allowable ambient temperature
(lead-acid battery)
-10℃～40℃14℉～104℉
Allowable ambient temperature (-
lithium battery)
-20℃～40℃-4℉～104℉
Max allowable RH 90%
Storage environment
Stored at -20℃to 50℃(-4℉to 122℉) in a well-ventilated environment with
90% relative humidity (20℃[68℉]), and away from rain, sun, corrosive
gas,inflammables and explosives.
WEIGHT
Gross weight (unladen) 11502 kg 25358 lb
Table 1-3 TB20E Plus specifications
MEASURE TB20E Plus (METRIC) TB680E Plus (IMPERIAL)
DIMENSION
Max platform height 20.6 m 67ft 7in
Max working height 22.6 m 74ft 2in
Max horizontal reach (restricted/
unrestricted) 13.0 m/14.7 m 42ft 8in / 48ft 2in
Overall length(stowed) 9.63 m 31ft 7in
Overall width(stowed) 2.49 m 8ft 2in
Overall height (stowed) 2.81 m 9ft 3in

MACHINE SPECIFICATIONS
TB18E Plus&20EJ Plus&20E Plus&22EJ Plus Operation Manual 1-5 © Oct 2021
Table 1-3 TB20E Plus specifications (continued)
MEASURE TB20E Plus (METRIC) TB680E Plus (IMPERIAL)
Wheelbase 2.49 m 8ft 2in
Ground clearance 0.39 m 1ft 3in
Tire size (spec / type)
Options
36×14-20（non-marking）
36×14-20（solid）
355/65D625（foam-filled）
Platform dimension (L×W×H)
Options
1.45×0.85×1.1 m
1.83×0.85×1.1 m
2.44×0.91×1.1 m
Options
4ft 9in×2ft 9in×3ft 7in
6ft×2ft 9in×3ft 7in
8ft×2ft 11in×3ft 7in
PERFORMANCE
Rated platform capacity (restricted/
unrestricted) 454 kg/300 kg 1000 lb / 661 lb
Max number of occupants
(restricted/unrestricted) 3/2
Turntable rotation/continuous 360 °/continuous
Platform rotation 160°
Max drive speed (stowed) 4.8km/h 3 mph
Max drive speed (raised) 1.1 km/h 0.68 mph
Drive mode (drive×steer) 4WD×2WS
Gradeability 35%/19°
Turntable tailswing 1.45 m 4ft 9in
Max allowable inclination 5°
Turning radius (inside) 2.4 m 7ft 10.5in
Turning radius (outside) 5.55 m 18ft 2.5in
Max allowable side force(restricted/
unrestricted) 600 N/400 N 134 lbf/90 lbf
Max operating noise level 80 dB
IP grade IP65
POWER
Motor（Volts/kW）29 V DC,15 kW
Duplex gear pump displacement 16 ml/r + 4 ml/r
Hydraulic tank capacity 170 L 37.4gal（UK）/44.9gal（US）
Hydraulic system pressure 28MPa 4061 Psi
Battery (number×voltage, capacity) 2×24V, 480Ah（lead-acid battery）
2×24V, 528Ah（lithium battery）
Power system voltage 48 VDC

© Oct 2021 1-6 TB18E Plus&20EJ Plus&20E Plus&22EJ Plus Operation Manual
MACHINE SPECIFICATIONS
Table 1-3 TB20E Plus specifications (continued)
MEASURE TB20E Plus (METRIC) TB680E Plus (IMPERIAL)
Control system voltage 12 VDC
Charger（input voltage/output
current）100～240 V AC,60 A
GROUND BEARING DATA
Max tire load 6820 kg 15036 lb
Pressure against ground 700 KPa 102 Psi
ENVIRONMENT
Max allowable wind speed 12.5 m/s 28 mph
Max allowable altitude 1000 m 3280 ft
Allowable ambient temperature
(lead-acid battery)
-10℃～40℃14℉～104℉
Allowable ambient temperature (-
lithium battery)
-20℃～40℃-4℉～104℉
Max allowable RH 90%
Storage environment
Stored at -20℃to 50℃(-4℉to 122℉) in a well-ventilated environment with
90% relative humidity (20℃[68℉]), and away from rain, sun, corrosive
gas,inflammables and explosives.
WEIGHT
Gross weight (unladen) 12025 kg 26510 lb
Table 1-4 TB22EJ Plus specifications
MEASURE TB22EJ Plus (METRIC) TB740EJ Plus (IMPERIAL)
DIMENSION
Max platform height 22.5 m 74ft
Max working height 24.5 m 80ft 5in
Max horizontal reach (restricted/
unrestricted) 12.7 m/14.3 m 41ft 8in/46ft 11in
Overall length(stowed) 10.68 m 35 ft
Overall width(stowed) 2.49 m 8ft 2in
Overall height (stowed) 2.81 m 9ft 3in
Wheelbase 2.49 m 8ft 2in
Ground clearance 0.39 m 1ft 3in
Tire size (spec / type)
Options
36×14-20（non-marking）
36×14-20（solid）
355/65D625（foam-filled）
Platform dimension (L×W×H) Options
1.45×0.85×1.1 m
Options
4ft 9in×2ft 9in×3ft 7in

MACHINE SPECIFICATIONS
TB18E Plus&20EJ Plus&20E Plus&22EJ Plus Operation Manual 1-7 © Oct 2021
Table 1-4 TB22EJ Plus specifications (continued)
MEASURE TB22EJ Plus (METRIC) TB740EJ Plus (IMPERIAL)
1.83×0.85×1.1 m
2.44×0.91×1.1 m
6ft×2ft 9in×3ft 7in
8ft×2ft 11in×3ft 7in
PERFORMANCE
Rated platform capacity (restricted/
unrestricted) 454 kg/300 kg 1000 lb / 661 lb
Max number of occupants
(restricted/unrestricted) 3/2
Turntable rotation/continuous 360 °/continuous
Platform rotation 160°
Max drive speed (stowed) 4.8km/h 3 mph
Max drive speed (raised) 1.1 km/h 0.68 mph
Drive mode (drive×steer) 4WD×2WS
Gradeability 35%/19°
Turntable tailswing 1.45 m 4ft 9in
Max allowable inclination 5°
Turning radius (inside) 2.4 m 7ft 10.5in
Turning radius (outside) 5.55 m 18ft 2.5in
Max allowable side force(restricted/
unrestricted) 600 N/400 N 134 lbf/90 lbf
Max operating noise level 80 dB
IP grade IP65
POWER
Motor（Volts/kW）29 V DC,15 kW
Duplex gear pump displacement 16 ml/r + 4 ml/r
Hydraulic tank capacity 170 L 37.4gal（UK）/44.9gal（US）
Hydraulic system pressure 28MPa 4061 Psi
Battery (number×voltage, capacity) 2×24V, 480Ah（lead-acid battery）
2×24V, 528Ah（lithium battery）
Power system voltage 48 VDC
Control system voltage 12 VDC
Charger（input voltage/output
current）100～240 V AC,60 A
GROUND BEARING DATA
Max tire load 6820 kg 15036 lb
Pressure against ground 700 KPa 102 Psi

© Oct 2021 1-8 TB18E Plus&20EJ Plus&20E Plus&22EJ Plus Operation Manual
MACHINE SPECIFICATIONS
Table 1-4 TB22EJ Plus specifications (continued)
MEASURE TB22EJ Plus (METRIC) TB740EJ Plus (IMPERIAL)
ENVIRONMENT
Max allowable wind speed 12.5 m/s 28 mph
Max allowable altitude 1000 m 3280 ft
Allowable ambient temperature
(lead-acid battery)
-10℃～40℃14℉～104℉
Allowable ambient temperature (-
lithium battery)
-20℃～40℃-4℉～104℉
Max allowable RH 90%
Storage environment
Stored at -20℃to 50℃(-4℉to 122℉) in a well-ventilated environment with
90% relative humidity (20℃[68℉]), and away from rain, sun, corrosive
gas,inflammables and explosives.
WEIGHT
Gross weight (unladen) 12260 kg 27029 lb
Note：
a) The working height adds 2m(6ft7in) of human height to platform height。
b) The ground bearing data is approximate value, not factoring the different options,thus it serves only in adequately safe
conditions
c) In different areas, hydraulic oil, engine oil, coolant, fuel and lubrication should be added in accordance with the
environmental temperature.
d) In cold weather, auxiliary devices are needed to start the machines.
e) Rated platform capcity represents the rated load of the platform, including the loads of persons, materials, tools, platform
accessories and other objects borne by the platform.