Siqura MSD622 User manual

Siqura MSD622
Outdoor IP PTZ Dome with Day/Night and WDR
Installation Manual

Note: To ensure proper operation, please read this manual thoroughly before using the product and retain the
information for future reference.
Copyright © 2011 Siqura B.V.
All rights reserved.
MSD622 1.0.0
Installation Manual v1.0 (112502-1)
AIT5.4-MW07SP2
Nothing from this publication may be copied, translated, reproduced, and/or published by means of printing,
photocopying, or by any other means without the prior written permission of Siqura.
Siqura reserves the right to modify specifications stated in this manual.
Brand names
Any brand names mentioned in this manual are registered trademarks of their respective owners.
Liability
Siqura accepts no liability for claims from third parties arising from improper use other than that stated in this
manual.
Although considerable care has been taken to ensure a correct and suitably comprehensive description of all
relevant components, the manual may nonetheless contain errors and inaccuracies.
Should you detect any errors or inaccuracies in the manual, we would be grateful if you would inform us. This helps
us to further improve our documentation.
More information
If you have any comments or queries concerning any aspect related to the product, please do not hesitate to
contact:
The Netherlands
Corporate Headquarters
Siqura B.V.
Zuidelijk Halfrond 4
2801 DD Gouda, The Netherlands
General : [phone]
Fax : [phone]
E-mail : [email protected]
WWW : http://www.siqura.com/
USA
US Corporate Offices
TKH Security Solutions USA, Inc.
12920 Cloverleaf Center Drive
Germantown, Maryland 20874, USA
General : [phone]
Fax : [phone]
E-mail : [email protected]
WWW : http://www. tkhsecurity-usa.com/

Page i
Contents
1INTRODUCTION.....................................................................................................................................1
2SAFETY..................................................................................................................................................3
2.1 SAFETY INFORMATION ................................................................................................................................. 3
2.2 REGULATIONS ............................................................................................................................................ 5
2.3 CAUTIONS ................................................................................................................................................. 5
3PRODUCT DESCRIPTION ........................................................................................................................7
3.1 PRODUCT OVERVIEW .................................................................................................................................. 7
3.2 GENERAL OPERATION REQUIREMENTS ............................................................................................................ 7
3.3 PACKAGE CONTENTS ................................................................................................................................... 8
4DOME SETUP AND CABLE CONNECTION.................................................................................................9
4.1 PREPARING THE MSD622 FOR INSTALLATION.................................................................................................. 9
4.2 SWITCH DEFINITION .................................................................................................................................. 10
4.3 COMMUNICATION SWITCH CONFIGURATION.................................................................................................. 10
4.4 ESTABLISHING A NETWORK CONNECTION ...................................................................................................... 11
4.5 SYSTEM COMPATIBILITY ............................................................................................................................. 12
4.6 DOME CABLE DEFINITION AND REQUIREMENTS .............................................................................................. 12
4.6.1 Cable requirements ......................................................................................................................... 13
4.6.2 Verifying Ethernet connectivity ....................................................................................................... 13
4.6.3 22-pin cable harness........................................................................................................................ 13
4.6.4 22-pin connector definition ............................................................................................................. 14
5DOME INSTALLATION .......................................................................................................................... 15
5.1 DOME DIMENSIONS .................................................................................................................................. 15
5.2 INSTALLATION SCENARIOS .......................................................................................................................... 16
5.3 CEILING MOUNT ...................................................................................................................................... 17
5.3.1 Ceiling mounting with a straight tube............................................................................................. 17
5.4 WALL MOUNT ......................................................................................................................................... 18
5.4.1 Mini wall mount .............................................................................................................................. 18
5.4.2 Wall mounting with gooseneck tube............................................................................................... 19
5.4.3 Wall box mounting .......................................................................................................................... 20
5.5 CORNER MOUNT...................................................................................................................................... 21
5.6 POLE MOUNT .......................................................................................................................................... 22
5.6.1 Pole thin/wide direct mounting....................................................................................................... 22
5.6.2 Pole thin/wide box mounting .......................................................................................................... 23
6SYSTEM INTEGRATION ........................................................................................................................ 25
APPENDIX A: CAMERA ACCESSORIES ........................................................................................................... 27
MOUNTING ACCESSORIES........................................................................................................................................ 27
MSD622 ACCESSORIES .......................................................................................................................................... 31
APPENDIX B: TECHNICAL SPECIFICATIONS.................................................................................................... 33

Page 1
Chapter 1
1Introduction
Document scope
This manual applies to Siqura's indoor and outdoor IP PTZ dome cameras, the MSD622 series. It
describes how to install and connect the MSD622 camera. Operation and configuration of the
MSD622 camera is covered in the user manual.
Intended audience
This manual is aimed at installers and technicians involved in the installation of network devices,
such as the MSD622.
Assumed skills and know-how
To work with the MSD622 camera, an installer or technician must have adequate knowledge and
skills in the fields of:
CCTV systems and components
Electrical wiring and low-voltage electrical connections
Ethernet network technologies and Internet Protocol (IP)
Windows environments
Web browsers
Video, audio, data, and contact closure transmissions
Video compression methods
Specifications
The information given in this manual was current when published. Siqura reserves the right to
revise and improve its products. All specifications are subject to change without notice.
Important information
Before proceeding, please read and observe all instructions and warnings in this manual. Retain
this manual with the original bill of sale for future reference and, if necessary, warranty service.
When unpacking your product, check for missing or damaged items. If any item is missing, or if
damage is evident, do not install or operate this product. Contact your supplier for assistance.

Siqura MSD622
Page 2
Typographical Conventions
Before you start using this guide, it is important to understand the typographical conventions
used in the documentation. The following kinds of formatting in the text identify special
information.
Formatting convention Type of Information
Numbered list Step-by-step procedures. You can follow these instructions to
complete a specific task.
Special Bold Items you must select, such as menu options, command buttons, or
items in a list.
Emphasis Used to emphasize the importance of a point or for variable
expressions such as parameters.
CAPITALS Names of keys on the keyboard. for example, SHIFT, CTRL, or
ALT.
KEY+KEY Key combinations for which the user must press and hold down one
key and then press another, for example, CTRL+P, or ALT+F4.

Page 3
Chapter 2
2Safety
In This Chapter
Safety Information............................................................. 3
Regulations....................................................................... 5
Cautions ........................................................................... 5
2.1 Safety Information
Introduction
The safety information contained in this section, and on other pages of this manual, must be
observed whenever this unit is operated, serviced, or repaired. Failure to comply with any
precaution, warning, or instruction noted in the manual is in violation of the standards of design,
manufacture, and intended use of the module. Siqura assumes no liability for the customer's
failure to comply with any of these safety requirements.
Trained Personnel
Installation, adjustment, maintenance, and repair of this equipment are to be performed by
trained personnel aware of the hazards involved. For correct and safe use of the equipment and
in order to keep the equipment in a safe condition, it is essential that both operating and
servicing personnel follow standard safety procedures in addition to the safety precautions and
warnings specified in this manual, and that this unit be installed in locations accessible to trained
service personnel only.
Safety Requirements
The equipment described in this manual has been designed and tested according to the
UL/IEC/EN 60950-1 safety requirements.
Warning: If there is any doubt regarding the safety of the equipment, do not put it into
operation.
This might be the case when the equipment shows physical damage or is stressed beyond
tolerable limits (for example, during storage and transportation).
Important: Before opening the equipment, disconnect it from all power sources.
The equipment must be powered by a SELV*power supply. This is equivalent to a Limited Power
source (LPS, see UL/IEC/EN 60950-1 clause 2.5) or a "NEC Class 2" power supply. When this
module is operated in extremely elevated temperature conditions, it is possible for internal and
external metal surfaces to become extremely hot.
*SELV: conforming to IEC 60950-1, <60VDC output, output voltage galvanically isolated from mains. All
power supplies or power supply cabinets available from Siqura comply with these SELV requirements.

Siqura MSD622
Page 4
EMC
The equipment has been tested and found to meet the CE-regulations relating to EMC, and
complies with the limits for a Class B device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against interference to radio communications in
any installation. The equipment generates, uses, and can radiate radio frequency energy;
improper use or special circumstances may cause interference to other equipment or a
performance decrease due to interference radiated by other equipment. In such cases, the user
will have to take appropriate measures to reduce such interactions between this and other
equipment.
Any interruption of the shielding inside or outside the equipment could make the equipment
more prone to fail EMC requirements.
Non-video signal lines must use appropriate shielded Cat 5 cabling (S-FTP), or at least an
equivalent. Ensure that all electrically connected components are carefully earthed and
protected against surges (high voltage transients caused by switching or lightning).
ESD
Electrostatic discharge (ESD) can damage or destroy electronic components. Proper precautions
should be taken against ESD when opening the equipment.

Safety
Page 5
2.2 Regulations
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions.
This device may not cause harmful interference.
This device must accept any interference received, including interference
that may cause undesired operation.
This symbol on the product or on its packaging indicates that this product shall not
be treated as household waste in accordance with Directive 2002/96/EC. Instead
it shall be handed over to the applicable collection point for the recycling of
electrical and electronic equipment. By proper waste handling of this product you
ensure that it has no negative consequences for the environment and human
health, which could otherwise be caused if this product is thrown into the garbage
bin. The recycling of materials will help to conserve natural resources.
For more information on how to recycle this product, please contact your local city
office, your household waste disposal service or the seller of the product.
Compliance is evidenced by written declaration from our suppliers, assuring that
any potential trace contamination levels of restricted substances are below the
maximum level set by EU Directive 2002/95/EC, or are exempted due to their
application.
2.3 Cautions
Handle the camera carefully.
Do not abuse the camera. Avoid striking, shaking, etc. as the camera can be damaged by
improper handling or storage.
Install electrical wiring carefully.
Ask a qualified electrician to perform the wiring for the installation. Please note that input
electricity to the unit is at a tolerance of 24VAC 50/60 Hz ± 10%. Ground the camera
appropriately to prevent electric shock or damage.
Cable harness Power input: 3-pin terminal block
Do not disassemble the camera.
To prevent electric shock, do not remove screws or covers. There are no user serviceable parts
inside. Please consult technical support if a camera is suspected of malfunctioning.
Do not operate the camera beyond the specified temperature,
humidity, and power source ratings
Use the indoor camera under conditions where the temperature is between 0°C~40°C
(32°F~104°F).

Siqura MSD622
Page 6
Do not block the cooling vent on indoor cameras.
This camera has a cooling fan inside. Blocking the cooling holes may lead to overheating and
cause malfunction. Overheating is not covered by warranty.
Do not expose the indoor dome camera to moisture or operate it
in wet areas.
The indoor dome camera is designed for indoor use or use in locations where it is protected from
rain and moisture. If the indoor camera gets wet, turn the power off immediately and ask a
qualified technician for servicing. Moisture can damage the indoor camera and also create the
danger of electric shock.
Do not use strong or abrasive detergents when cleaning the
camera.
Use a dry cloth to clean the camera when it is dirty. If the dirt is hard to remove, use a mild
detergent and wipe gently. To clean the lens, use lens tissue or a cotton tipped applicator and
ethanol. DO NOT clean the lens with strong detergents.
Never face the camera towards the sun.
Do not aim the camera at bright objects. Whether the camera is in use or not, never aim it at the
sun or other extremely bright objects, as this can damage the camera.

Page 7
Chapter 3
3Product Description
The MSD622 PTZ dome camera is designed to deliver superb performance and durability with an
intelligent and stylish housing suitable in any security and surveillance installation. With weather
resistant housing (IP66 and sunshield), the outdoor dome camera (Siqura MSD622) can face
harsh circumstances.
In This Chapter
Product Overview............................................................... 7
General Operation Requirements ......................................... 7
Package Contents .............................................................. 8
3.1 Product Overview
Siqura MSD 622 Features
Vandal-resistant outdoor mini network PTZ dome camera
Quad stream support Dual H.264, MPEG-4 and MJPEG
Open Streaming Architecture (OSA)
Up to 144x zoom (12x optical zoom/12x digital zoom)
Auto day/night
Back Light Compensation
300° / second Preset targeting
360° endless panning
256 presets/1 programmable cruise
8 alarm in/1 output
Two-way audio
16 Privacy Masks
Analog Output
IP66 ingress protection
Polycarbonate bubble
24 VAC
3.2 General Operation Requirements
A minimum of one control device is required for operation, such as a control keyboard, a DVR, or
a PC. The MSD622 contains a built-in receiver that decodes commands originating from a control
device.
The built-in Pelco D protocol provides connectivity to other surveillance systems and allows the
MSD622 to be integrated with other suppliers' surveillance systems.
For more detailed information, see Appendix B: Technical Specifications.

Siqura MSD622
Page 8
3.3 Package Contents
Before proceeding, please verify that the box contains the items listed here. If any item is
missing or has defects, do not install or operate the product. Contact your supplier for
assistance.
Siqura MSD622 package contents
Dome body M3 standard screw (x1)
M3 security screw (x1)
M5 standard screw (x1)
M5 security screw (x1)
30 cm cable harness
Optical cover Waterproof Boot Security TORX
Lubricant Quick start guide CD; manuals and software utilities

Page 9
Chapter 4
4Dome Setup and Cable Connection
Before installing or connecting the MSD622, please refer to this section and complete the
preliminary preparations for setting up the dome camera and establishing switch settings.
In This Chapter
Preparing the MSD622 for Installation .................................. 9
Switch Definition................................................................ 10
Communication Switch Configuration.................................... 10
Establishing a Network Connection....................................... 11
System Compatibility.......................................................... 12
Dome Cable Definition and Requirements.............................. 12
4.1 Preparing the MSD622 for Installation
This preliminary installation procedure is for the MSD622 dome cameras.
Perform the following steps to prepare the dome camera for installation
1. Unpack the dome package and take out the dome body.
2. Remove the tube adaptor by rotating counter clockwise.
3. Rotate to remove the protective cover.
4. Make a note of the IP address on the label attached to the cylindrical heat sink.
5. Remove the PE cloth and take off the lens cap.
6. Generously apply the supplied lubricant to the optical cover’s waterproof boot to ensure an
IP66 quality installation.
7. Loosen the screw head alignment pins on the dome cover by turning clockwise and line up
the alignment pin and screws on the optical cover with the holes in the dome body.
8. Attach the optical cover to the dome body by pressing gently down on the sides of the dome
cover.
9. Turn the screw head alignment pins counter-clockwise with a suitable screwdriver to lock
the dome into place and secure the dome with the included Phillips-head or TORX screw.

Siqura MSD622
Page 10
4.2 Switch Definition
It is necessary that the dome ID and communication protocol remain in the default modes when
connecting the MSD622 cameras to other devices. The switches used for configuring these
settings are located on the bottom of the dome camera. These settings are preset to operate the
camera with the IP hardware. Changing the settings may make the camera inoperative using the
IP connection.
Refer to the figure and table below for switch location and definitions.
MSD622 switches
Switch Definition
A Communication switch
B ISP connector (for firmware upgrades)
C RJ-45/SFP connector
D SD card slot
E Reset buttons
F 22-pin connector
Note: Switch E has two buttons. Only the button closest to the 22-pin connector is used to
restore factory server defaults. The other button is reserved.
To restore factory server defaults
Power up the camera while holding button E. Continue to hold the button for 30 seconds
after powering the camera.
4.3 Communication Switch Configuration
The MSD622's communication switch is specified in the table below. The default settings are
depicted in the figure. You are advised to verify the accuracy of the communication switch
configuration but do not change the default settings, or some functions may not work properly.

Dome Setup and Cable Connection
Page 11
Communication Switch Switch Description
1
RS-485
2
3 Termination
4 Line lock
5 System initialization. Switch 5 is mainly used to restore the
camera's factory defaults.
6 Camera upgrade. Users must reset switch 6 after firmware
upgrades are carried out.
RS-485 is the interface that enables communication between the MSD622 and its control device.
This means that the camera's RS-485 setup and that of the control device must be the same. The
RS-485 default setting is half-duplex, as shown in the figure below. Please do not change the
default setting without consulting a qualified specialist or supplier.
Half duplex Full duplex
RJ-485 settings
4.4 Establishing a Network Connection
To open communication with the MSD622 from a host PC and change the unit's network settings,
perform the following steps.
Step 1: Set the PC's network adapter to the unit's factory default subnet and connect
the two devices.
Step 2: Access the unit from a web browser or other tool installed on the PC.
Step 3: Set the unit's IP address and subnet mask to the subnet it will be used in and
reboot the unit.
To address the unit from the same PC again, configure the PC's network adapter once more to
assign the PC to the same subnet as the unit.
Step 1: Setting the host PC to the factory default subnet of the unit
To configure the network adapter on the host PC
1. In the Control Panel, open Network Connections.
2. Right-click the connection to be configured, and select Properties.
3. In the items list, select Internet Protocol (TCP/IP).
4. Click
Properties.
5. In the Internet Protocol (TCP/IP) Properties dialog, click Use the following IP address.
6. Enter an IP address that will assign your PC to the same subnet as the unit (i.e., within the
10.x.x.x range). Use 255.0.0.0 as a subnet mask.

Siqura MSD622
Page 12
Important: To prevent conflicts, be sure to choose a unique IP address. No two devices on a
network can have the same IP address.
7. To apply the new settings, click OK, and then click Close.
Opening IP settings on the host PC Changing host PC IP settings to the factory-default
settings of the unit
At this point, connect your PC to the MSD622. You can connect them directly using a crossover
cable, or connect both to a switch.
Step 2: Accessing the unit
Using a standard web browser you can now log on to the MSD622's internal web server.
Step 3: Changing the unit's network settings
The Network web page enables you to make the unit's network addressing compatible with the
network it will be hooked into. You can set a fixed IP address or have the IP address assigned by
a DHCP server. In the latter case, open the Advanced Settings and enable DHCP. Do not forget
to save and reboot the unit after changing the settings.
4.5 System Compatibility
To ensure system compatibility, download the latest firmware from Support > Software on the
Optelecom-NKF web site at http://www.siqura.com/. Registration is required.
4.6 Dome Cable Definition and Requirements
For operation, the MSD622 cameras require either an Ethernet cable or an appropriate fiber optic
cable to carry the signals to a remote viewing site and a cable to power the dome.

Dome Setup and Cable Connection
Page 13
4.6.1 Cable requirements
For operation, the camera requires a video and cable harness, as described below.
A cable to provide a 24 VAC power supply to the dome.
A Cat-5 Ethernet cable.
Optional audio cables.
Optional coaxial cable to monitor analog video.
Important: Ensure the power supply corresponds with the dome's power requirement, or damage
will occur. If any mistake happens, contact a qualified technician.
4.6.2 Verifying Ethernet connectivity
Refer to the following figure to determine whether you have established an Ethernet connection.
Ethernet socket LEDs green/yellow
Green on/off : 100/10 Mbit
Yellow on/blink
Yellow off/flash
4.6.3 22-pin cable harness
The MSD622's 22-pin cable harness

Siqura MSD622
Page 14
4.6.4 22-pin connector definition
With the 22-pin connector, installers can simply connect the power and video cables to the dome
at the same time. The alarm pins are serviceable for connecting alarm input and output devices,
such as alarm sensors, sirens, or flashing lights with the surveillance system. For the definition
of each pin, please refer to the table below.
22-pin connector
The definitions of each pin are listed in the following table.
Pin Definition Cable Color Rating
1 AC 24-1/DC (+) 20/18 AWG Red
2 Alarm, normally closed
White Photo Relay output 300V
3 AC 24-2/DC (-) 20/18 AWG Black
4 Alarm, normally open White/black Photo Relay output 300V
5 FG 20/18 AWG Yellow
6 Alarm COM
24 AWG
Green/black Photo Relay output 300V
7 Audio in Yellow/black
8 Audio out Orange/black
9 Audio GND Green/black
10 Audio GND Brown/black
11 ISOG Blue/white
12 Alarm 1 Red/white
Input 5V 10KO pull up
Photo Relay output 300V
13 Alarm 3 Purple
14 Alarm 2 Gray
15 Alarm 4 Blue
16 Alarm 5 White/black
17 Alarm 6 Orange/black
18 Alarm 7 Purple/white
19 Alarm 8 Gray/black
20 Alarm GND Brown/white Input 5V 10KO pull up
21 Video GND
20 AWG
Black/gray
22 Video Red/gray

Page 15
Chapter 5
5Dome Installation
Based on the installation environment, the MSD622 camera can be installed using a ceiling, wall,
corner, or pole mount. In the following sections, various installation methods and installation
procedures are described in detail.
In This Chapter
Dome Dimensions.............................................................. 15
Installation Scenarios ......................................................... 16
Ceiling Mount .................................................................... 17
Wall Mount........................................................................ 18
Corner Mount .................................................................... 21
Pole Mount........................................................................ 22
5.1 Dome Dimensions
The MSD622 dome dimensions are 133 x 173 mm (5.2 x 6.8 in.). The diagrams below show
detailed dimensions for dome’s different parts.
The Siqura MSD 622 dome dimensions are Ø190 x 260 mm (7.5 x 10.2 in.). The diagrams below
show detailed dimensions of the dome’s different parts.
MSD622 dimensions

Siqura MSD622
Page 16
5.2 Installation Scenarios
Choose your installation scenario from the list below for complete instructions for performing
that installation.
Important: Whatever your scenario, always use the safety line when attaching the dome.
Ceiling mounts
Ceiling mounting with a straight tube
Wall mounts
Mini wall mount
Wall mounting with gooseneck tube
Wall box mounting
Corner mounts
Corner Mount
Pole mounts
Pole thin/wide direct mounting
Pole thin/wide box mounting
For descriptions of the various accessories required for each installation, see Appendix A:
Camera Accessories.
Note: Some illustrations in this section use the term "plane washer". This is also known as a flat
washer.
Warning: Fully torque down the mounting bolt that attaches the
WM02 tube adapter to the mounting bracket to prevent any
movement of the camera due to wind, vibration, etc.
Make sure the camera cannot move at all in its bracket after
installation. Any movement of the camera in its bracket can
compromise positional accuracy.