SMART ATCA-7367 User manual

1 Box contents
Make sure you receive all items of your shipment:
• One ATCA-7367 blade
• Printed Quick Start Guide
• Printed Safety Notes Summary
• Any optional items ordered
When installing or servicing the system or accessories,
strictly observe the safety precautions in the Safety Notes
Summary. Ignoring these instructions can void the system
warranty and cause personal injury or property damage.
2 ESD
Electrostatic discharge and incorrect installation or
removal of the card can damage circuit or shorten its life.
Use a properly grounded ESD wrist strap or work in an
ESD-safe environment.
Connect to the ESD connector at the front or the rear of
the system.
3 Site preparation
1. Make sure that all environmental and power requirements
defined in the ATCA-7367 Installation and Use manual are
met.
2. For information on the environmental and power requirements,
see the ATCA-7367 Installation and Use manual.
3. Operating temperatures refer to the temperature of the air
circulating around the blade and not to the actual component
temperature.Install PCIE cards
For more information about PCIE card installation, refer to the
ATCA-7367 Installation and Use manual.
4 Install the DIMM
NOTES:
Some blade variants come with the DIMM already installed.
When installing DIMM memory modules, the DIMM sockets farthest
on each memory channel from the CPU device must be populated
first.
For thermal safety concerns, no 4-rank DIMMs and no dual-die
DIMMs are allowed.
1. If necessary, remove the blade from the system.
2. Open the locks of the memory module socket.
3. Press the memory module carefully into the socket. As soon as
the memory module is fully inserted, the locks automatically
close.
4. If necessary, repeat steps 2–3 to install additional memory
modules.
5 Install SATA storage
module
1. If necessary, remove the blade from the system.
2. Plug the storage module on the blade so that the module's
standoffs fit in the blade's mounting holes.
3. Fasten the memory module to the blade using the two screws
that previously had fixed the storage module to the blade.
4. Reinstall the blade in the system.The additional resource will be
detected automatically during the boot-up sequence.
6 Install USB 2.0 flash
module
NOTE:
Some blade variants come with the flash module already installed.
1. If necessary, remove the blade from the system.
2. Insert the new flash module in the socket.
3. Tighten the screw on the left side of the flash module.
7 Install the blade
The following procedure assumes that the system is powered. If it is
unpowered, you can disregard the blue LED and skip its respective
step.
1. Ensure that the top and bottom ejector handles are in the
outward position by squeezing the lever and the latch
together.
2. Insert the blade into the shelf by placing the top and bottom
edges of the blade in the card guides of the shelf. Ensure that the
guiding module of the shelf and blade are aligned properly.
3. Apply equal and steady pressure to the blade to carefully slide
the blade into the shelf until you feel resistance. Continue to
gently push the blade until the blade connectors engage.
4. Squeeze the lever and the latch together and hook the lower and
the upper handle into the shelf rail recesses.
5. Fully insert the blade and lock it to the shelf by squeezing the
lever and the latch together and turning the handles towards the
face plate.
If your shelf is powered, as soon as the blade is connected to the
backplane power pins, the blue LED is illuminated.
When the blade is completely installed, the blue LED starts to blink.
This indicates that the blade announces its presence to the shelf
management controller.
ATCA-7367
Quick Start Guide
P/N: 6806800K73E December 2019

ATCA-7367 Quick Start Guide
SMART Embedded Computing, 2900 S. Diablo Way, Suite 190, Tempe, Arizona 85282
Note: If an RTM is connected to the front blade, make sure that the
handles of both the RTM and the front blade are closed in order to
power up the blade’s payload.
6. Wait until the blue LED is switched off, then tighten the face plate
screws which secure the blade to the shelf.
The switched off blue LED indicates that the blade’s payload has
been powered up and that the blade is active.
7. 7. If necessary, connect cables to the face plate.
.
For technical assistance or to report product damage or shortages,
contact your local SMART Embedded Computing sales
representative or visit https://www.smartembedded.com/ec/support/
Technical Assistance
For more information on this product, see the ATCA-7367
Installation and Use manual and other related technical
documentation, which can be found by using the
Documentation Search at
https://www.smartembedded.com/ec/support/.
Get More Information
© 2019 SMART Embedded Computing™, Inc.All rights reserved. The stylized “S” and
“SMART” is a registered trademark of SMART Modular Technologies, Inc. and “SMART
Embedded Computing” and the SMART Embedded Computing logo are trademarks of
SMART Modular Technologies, Inc. All other names and logos referred to are trade names,
trademarks, or registered trademarks of their respective owners. These materials are
provided by SMART Embedded Computing as a service to its customers and may be used
for informational purposes only. For full legal terms and conditions, visit
www.smartembedded.com/ec/legal.